LEHX 16Pin Wire Harness with Canbus Box

Contents

LEHX Car Android Radio Player 16Pin Wire Harness with Canbus Box User Manual

Model: 16Pin Wire Harness with Canbus Box

Brand: LEHX

Introduction

This manual provides comprehensive instructions for the installation, operation, and troubleshooting of the LEHX 16Pin Wire Harness with Canbus Box. This product is designed to facilitate the integration of an Android multimedia player into compatible Chevrolet and Buick vehicle models. Please read this manual thoroughly before installation and use to ensure proper functionality and avoid potential issues.

LEHX Car Android Radio Player 16Pin Wire Harness with Canbus Box for Chevrolet Trax/Cruze
Figure 1: Overview of the LEHX 16Pin Wire Harness with Canbus Box and accessories.
Close-up of the 16Pin wire harness and Canbus box
Figure 2: Detailed view of the 16Pin wire harness and Canbus box.

Compatibility

This wire harness and Canbus box are compatible with the following vehicle models:

  • Chevrolet Trax: 2014-2016
  • Chevrolet Cruze: 2012-2016
  • Chevrolet Aveo (Sonic): 2012-2016
  • Chevrolet Malibu: 2013-2015
  • Buick Regal: 2011-2013
16P Car Android Multimedia Player Power Cable Adapter
Figure 3: The 16P power cable adapter, which must match your multimedia player's cable adapter.

Setup and Installation

Before Installation

Before installing the product directly into your car, it is recommended to test the unit. Due to potential impacts during long transit, the product's functionality might be affected. Please test the machine thoroughly before proceeding with the full installation.

Rear Interface Description

The wire harness connects to the 16PIN power socket of your Android multimedia player. Below is a detailed description of the pin definitions and connections:

16PIN Power Socket Interface Definition (P1 Port)

This section describes the pinout of the 16PIN power socket, including connections for speakers, power, control lines, and antenna. Refer to the original manual's diagram for visual representation.

  • Pin 1 (GND): Battery Negative (Ground Wire/B-)
  • Pin 2 (B+): Battery Positive (Constant Power Supply +12V)
  • Pin 3 (ACC): Ignition Switch
  • Pin 4 (ILL): Illuminate Backlight (Day and Night Mode)
  • Pin 5 (BACK): Reversing Camera Control Line
  • Pin 6 (ANT): Auto Antenna Power
  • Pin 7 (KEY1): Steering Wheel Controls 1
  • Pin 8 (KEY2): Steering Wheel Controls 2
  • Pin 9 (FR-): Front Right Speaker Negative
  • Pin 10 (FR+): Front Right Speaker Positive
  • Pin 11 (FL-): Front Left Speaker Negative
  • Pin 12 (FL+): Front Left Speaker Positive
  • Pin 13 (RL-): Rear Left Speaker Negative
  • Pin 14 (RL+): Rear Left Speaker Positive
  • Pin 15 (RR-): Rear Right Speaker Negative
  • Pin 16 (RR+): Rear Right Speaker Positive

Additional Connections:

  • F-CAM (VIDEO-IN-2): Video Input 2 (Front Camera Input)
  • AUX R IN: Right Audio Input
  • AUX L IN: Left Audio Input
  • VIDEO-IN-1: Video Input 1
  • VIDEO OUT: Video Output
  • FR OUT: Front Right Audio Output
  • FL OUT: Front Left Audio Output
  • SUB WOOF: Subwoofer Output
  • MIC: Microphone Input
  • AMP CONT: Amplifier Control
  • BT Antenna: Bluetooth Antenna
  • R-CAM: Reversing Camera Input
  • WiFi Antenna: Wi-Fi Antenna
  • USB1/2: USB Port
  • Protocol Box: Only use when needed.

Important Wiring Notes:

  • The unit turns on normally when both the yellow B+ line and the red ACC line receive a 12V positive power simultaneously.
  • The yellow B+ line maintains power for memory function.
  • Ensure that the 8 speaker cables are not grounded, shared, or touching other lines. Improper connection can lead to no sound output, distorted sound, or overheating.

Reversing Camera Installation Method

This section describes the wiring for a reversing camera, typically installed at the rear of the car. Refer to the original manual's diagram for visual representation.

Wiring Steps:

  1. Locate the reverse control line on the unit's power line (usually a pink wire). Connect this line to the 12V positive pole; the screen should turn blue.
  2. Find the CAM video input interface at the back of the unit. Identify the positive and negative terminals of the backup light.
  3. The camera typically has two sockets. Connect the red socket to the power cable and the yellow socket to the video cable. The red wire of the camera's power cable and the video cable's red wire are screwed together to the positive pole of the reverse lamp. The black wire of the power cable is not used.
  4. Connect the other end of the video cable to the CAM video input interface on the back of the unit. The red line extending from the video line connects to the reversing control line of the power line.

Important Note:

If a reversing camera is not installed, do not connect the REVERSE/BACK cable to any location. Leave it unconnected. Improper connection can cause the machine to display incorrectly or automatically enter reverse mode, potentially leading to malfunction. If this occurs, disconnect the REVERSE/BACK line as soon as possible.

CANBUS Connection

The CANBUS box is used for specific vehicle models to integrate with the car's internal systems. Refer to the original manual's diagrams for visual representation of the connection methods.

For High-End Model Cars:

Disconnect the existing connection and then connect the CANBUS box as shown in the diagram.

For Low-End Model Cars:

Connect the CANBUS box as shown in the diagram, then disconnect the other connection.

Attention:

If the CANBUS box and black buckle are connected simultaneously, it may cause the radio to fail to shut down after the car is turned off.

Operating Instructions

Learning Steering Wheel Controls

To configure steering wheel controls:

  1. Press and hold a button on your original car's steering wheel.
  2. Identify the corresponding button icon on the multimedia player's screen.
  3. Click the icon to change its color, indicating successful learning.

Example:

  • KEY1 (Orange/black wire)
  • KEY2 (Brown wire)
  • Common functions include: Source, Reset, Confirm, Volume Up/Down, Next/Previous Track.

Refer to the original manual's diagram for a visual example of the steering wheel control learning interface.

Apple CarPlay (Only some models support)

This feature allows seamless integration with your iPhone. Refer to the original manual's screenshots for interface examples.

1. Wired Connection:

  • Simply connect your iPhone using a USB data cable, and the CarPlay interface will launch automatically.

2. Wireless Connection:

  • First, enable Bluetooth and Wi-Fi on your mobile phone.
  • Connect to the unit's Bluetooth. The CarPlay interface will then launch automatically.
  • Note: The signal is transmitted via Wi-Fi. CarPlay will function normally even if Bluetooth is turned off. If Wi-Fi is turned off, CarPlay will disconnect.

Android Auto (Only some models support)

This feature may not be supported in all countries, and "Google Play" services must be available locally. Refer to the original manual's screenshots for interface examples.

Requirements:

  • Download and install "Android Auto" software from "Google Play".
  • Use a mobile phone with Android 6.0 or higher.
  • A valid data cable connection is required.

1. Wired Connection:

  • Simply connect your Android phone using a USB data cable, and the Android Auto interface will launch automatically.

2. Wireless Connection:

  • First, enable Bluetooth and Wi-Fi on your mobile phone.
  • Connect to the unit's Bluetooth. The Android Auto interface will then launch automatically.
  • Note: The signal is transmitted via Wi-Fi. Android Auto will function normally even if Bluetooth is turned off. If Wi-Fi is turned off, Android Auto will disconnect.

Maintenance

Regular checks and proper handling can extend the life of your device.

  • Fuse Replacement: If the unit experiences power issues or does not boot, check the fuse on the yellow line. If it is blown, replace it with a fuse of the correct rating (e.g., 12V-5A).
  • Remote Control Battery: If the remote control is unresponsive, check and replace its battery if necessary.
  • USB Drive Formatting: For USB devices that cannot be played, ensure the USB flash disk is formatted to FAT32. Re-download songs and try again. If issues persist, replace the USB flash drive.

Common Problems and Simple Troubleshooting

1. Cannot boot normally

  1. Incorrect Wiring: The "Yellow" (B+), "Red" (ACC), and "Black" (GND) wires are crucial. If only two of these three lines are connected, the unit will not start. Ensure the yellow line connects to positive, red to key control, and black to negative. Incorrect or insufficient connections will prevent booting.
  2. Incompatible Wiring: The original car wiring and unit wiring may not match by color. Connecting based on color alone can lead to non-functionality or even burning.
  3. Incorrect Plug Usage: The original car plug cannot be directly plugged into the new unit, even if it fits. It must be used with the provided harness.
  4. Blown Fuse: If the three wires are correctly connected but the unit doesn't boot, check the fuse on the yellow line. If the fuse is intact, twist the yellow and red wires together, turn on the key, and press the power button to test.
  5. Repeated Fuse Blowing: If the fuse blows every time it's replaced, it indicates a short circuit in the unit's protection circuit. The unit requires professional repair. Do not repeatedly replace fuses as this can cause further damage.
  6. Final Boot Test: If all connections seem correct and the unit still doesn't boot, connect the yellow and red wires directly to a 12V battery (positive) and the black wire to negative. Press the power button. If it boots, the original car wiring is incorrect. If it doesn't boot, the unit is faulty.

2. Automatic shut-down

  1. Cable Error: If the blue cable (automatic antenna power supply) is connected to the unit's power cable, it will automatically shut down. Follow the correct wiring method.
  2. Unstable Voltage: Find a 12V-5A power supply and re-test. If it still shuts down automatically, the unit is faulty. If it doesn't, the power supply is the issue.

3. There is noise

  1. Low Speaker Power: If the original speaker power is too low, increasing the unit's volume will cause noise. Solution: When replacing speakers or listening to music, avoid excessively high volume.
  2. Grounded Speaker Cable: If the speaker cable is grounded, connect the iron speaker cable directly to the unit's speaker cable.

4. Remote control cannot be used

  1. Test Method: Use your mobile phone camera to view the remote control's light while pressing buttons. If the light doesn't illuminate, replace the battery. If it lights up, the remote control is functional.

5. Settings cannot be saved (no memory)

  1. Incorrect Power Connections: The yellow (B+) and red (ACC) lines are connected together (yellow to positive, red to key control).
  2. Reversed Connections: The yellow and red lines are reversed (simply swap their positions).

6. Bluetooth not working

Turn on the unit, search for its Bluetooth name on your mobile phone, and click "Connect." After connecting, you should be able to make calls or play music via Bluetooth.

7. The product emits smoke

Replace the FUSE. If the problem persists, the internal circuit is burned. After-sales service is required.

8. The sound cannot be adjusted

  1. Reset the unit or unplug and replug the power cord.
  2. If the volume knob is broken, it needs to be replaced.

9. Reversing camera does not display

  1. Wrong or Missing Wiring: Refer to the "Reversing Camera Installation Method" in the Setup section.
  2. Faulty Camera: If the lamp connected to the camera doesn't light up, the camera is likely broken and needs replacement.

10. USB devices cannot be played

Format the USB flash disk to FAT32. Re-download one or two songs and try again. If it still doesn't work, replace the USB flash drive.

11. FM does not receive radio stations

  1. Antenna Issues: Ensure the antenna plug is fully inserted. Check if the antenna is disconnected or the line is broken.
  2. Station Search: Use the "AS" button for automatic search or manually search using the "before" or "after" buttons.
  3. Antenna Alternative: If the above doesn't resolve the issue, unplug the antenna plug and insert a screwdriver or metal strip in its place to test.

12. No sound right after installation

The unit is tested before shipment. If there's no sound, it's usually a wiring error or a short-circuited original car speaker wire. To check:

  1. Check if the speaker cable is short-circuited and connected. Reconnect if there's any short circuit.
  2. Verify the number of speaker cables. If your original car has only 2 speaker cables, but the unit requires 4, you need to re-route the original car line. One speaker needs 2 wires; two speakers need 4 wires.

13. No sound after a while

Disconnect all speaker cables from the unit (do not remove them). Connect an external speaker to the gray and purple wires of the tail line. Connect any green group and test for sound. If there is sound, the car's speaker line is short-circuited or the speaker is damaged. If there is no sound, the unit is broken.

Specifications

AttributeValue
Brand NameLEHX
DinDouble Din
Operating SystemAndroid
Voltage12 V
Item Weight0.1kg
Digital Media FormatCD
Display Size2.5"
OriginMainland China
For Vehicle Brands/ModelCHEVROLET
CertificationCE
TF/Micro SD Slot0
High-concerned chemicalNone

User Tips

  • Verify Vehicle Compatibility: Before purchasing or installing, always double-check that your specific car model and year are listed in the compatibility section to ensure proper fit and function. If your model is not listed, contact customer service for clarification.
  • Pre-Installation Test: As recommended in the manual, always test the unit's basic functions (power on, display) before full installation into the vehicle to identify any transit damage or defects early.
  • Wiring Diagrams: Pay close attention to the detailed wiring diagrams for the 16PIN power socket and reversing camera. Incorrect wiring is a common cause of issues like no power, no sound, or camera malfunction.

Warranty and Support

For any issues not covered in this manual or for professional assistance, please contact customer service. If the product emits smoke or has internal circuit damage, after-sales service is required.

Please note that if the device is updated, functions may be subject to change without prior notice.

You can find additional support and information through the following channels:

  • WhatsApp: Refer to the QR code provided in the product packaging or on the last page of the manual for direct support.
  • Social Media: Follow @LEHXCARRADIO on platforms like TikTok and Instagram for updates and support.

A user manual in PDF format is available for download. You can reference it for detailed diagrams and instructions: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.