Flipsky 7070 110KV

Contents

Flipsky Sensored Outrunner Brushless DC Motor 7070 110KV 4200W Instruction Manual

Model: 7070 110KV | Brand: Flipsky

Safety Warnings

⚠ Please read all instructions carefully before use. Failure to follow these instructions may result in property damage, personal injury, or fire.

  • Fire Risk: This product involves electrical components and high power. Always be aware of potential fire risks, especially during charging and storage of associated battery packs.
  • Charging and Storage: Strictly follow the instruction manual for charging and storage of all related components (e.g., batteries, ESCs).
  • Electrical Shock: Ensure all electrical connections are secure and insulated to prevent short circuits and electrical shock.
  • Moving Parts: Keep hands, hair, and loose clothing away from the motor and any rotating parts during operation.
  • Ventilation: Ensure adequate ventilation for the motor and Electronic Speed Controller (ESC) during operation to prevent overheating.

Product Overview

The Flipsky 7070 110KV 4200W Sensored Outrunner Brushless DC Motor is a high-performance motor designed for various electric applications, including electric skateboards, ebikes, scooters, and robotics. It features a battle-hardened design for enhanced durability and includes sensors for precise control.

Flipsky 7070 110KV 4200W Brushless DC Motor
Main product view of the Flipsky 7070 110KV 4200W Brushless DC Motor, highlighting its sensored, brushless, and 4200W features.

Specifications

FeatureSpecification
Max Power4200W
Motor KV110KV
Max Current100A
Voltage Range6-18S (LiPo cells)
Max Torque9.5 N.M
Internal Resistance0.055ohm
Motor Structure12N/14P
Dimensions (Diameter * Length)70mm * 70mm
Shaft Diameter10mm (Available in D-Shaft or Round Shaft)
Bullet Connector4mm
SensorYes
Line Length32cm
Hall Lead CorrespondenceRed - 5V, White - TEMP, Black - GND, Yellow - HALL1, Green - HALL2, Blue - HALL3

Performance Graph

Motor Performance Graph
Graph showing Speed (rpm), Torque (m-Nm), Current (Amp), Power (Watt), and Efficiency (%) for the 7070/110KV motor at 42V.

Dimensions

10MM D Shaft Motor Dimensions

10MM D Shaft Motor Drawing
Technical drawing illustrating the dimensions of the 10MM D Shaft motor variant.

10MM Round Shaft Motor Dimensions

10MM Round Shaft Motor Drawing
Technical drawing illustrating the dimensions of the 10MM Round Shaft motor variant.

Setup and Installation

Physical Installation

  • Mounting: Securely mount the motor to your application's frame using appropriate screws and mounting holes. Ensure the motor is firmly attached to prevent vibration and damage.
  • Shaft Type: Select the correct motor variant (10MM D Shaft, 10MM Round Shaft, or with pulley) that matches your drive system (e.g., pulley, gear).
  • Clearance: Ensure there is adequate clearance around the motor for cooling and to prevent interference with other components.
Motor with wires and connectors
The motor showing its phase wires and sensor cable, ready for connection.

Electrical Connections

  • Phase Wires: Connect the three main phase wires (typically yellow, blue, green) from the motor to the corresponding phase outputs on your Electronic Speed Controller (ESC). Use the provided 4mm bullet connectors or suitable alternatives.
  • Sensor Wire: Connect the sensor cable from the motor to the sensor port on your ESC. Ensure correct pin alignment. The Hall lead correspondence is:
    • Red: 5V
    • White: TEMP (Temperature Sensor)
    • Black: GND (Ground)
    • Yellow: HALL1
    • Green: HALL2
    • Blue: HALL3
  • Power Source: Connect your ESC to a compatible battery pack within the specified voltage range of 6-18S.
  • ESC Configuration: Refer to your ESC's instruction manual for proper configuration, including motor detection, timing, and other settings.

Operating Instructions

  • Pre-Operation Check: Before each use, inspect all connections, mounting points, and wires for any signs of damage or looseness.
  • Gradual Start-up: When first operating, apply power gradually to ensure smooth startup and proper motor function.
  • Monitoring: Monitor motor temperature during operation. Excessive heat can indicate an issue or improper setup.
  • Environmental Conditions: Avoid operating the motor in excessively wet or dusty conditions unless the entire system is designed for such environments.

Maintenance

  • Cleaning: Regularly clean the motor to remove dirt, dust, and debris that can accumulate and affect performance or cooling. Use compressed air or a soft brush.
  • Connection Check: Periodically check all electrical connections (phase wires, sensor wire) for tightness and corrosion.
  • Bearing Inspection: Listen for unusual noises from the motor, which could indicate worn bearings. While the motor is battle-hardened, bearings are still wear items.
  • Shaft Inspection: Inspect the motor shaft for any bends or damage.
  • Storage: Store the motor in a dry, cool place away from direct sunlight and extreme temperatures.

Troubleshooting

  • Motor Not Spinning:
    • Check all power connections from the battery to the ESC and from the ESC to the motor.
    • Verify that the ESC is properly configured and receiving a signal from your controller.
    • Inspect the sensor wire for damage or incorrect connection.
  • Irregular or Jerky Operation:
    • Ensure the sensor wire is correctly connected and not damaged.
    • Check for loose phase wire connections.
    • Recalibrate your ESC's motor detection or sensor settings.
  • Excessive Heat:
    • Ensure the motor is not overloaded for your application.
    • Check for proper ESC settings (e.g., motor timing).
    • Verify adequate airflow for cooling.
  • Unusual Noises:
    • Inspect for foreign objects lodged in the motor.
    • Check motor bearings for wear or damage.

User Tips

  • Value for Money: Users have noted the excellent quality and performance for the price.
  • Shaft Compatibility: Carefully consider your application's requirements for the motor shaft type (D-Shaft, Round Shaft, with/without pulley) before purchase.
  • ESC Pairing: Ensure your Electronic Speed Controller (ESC) is compatible with a sensored brushless motor and can handle the motor's maximum current (100A) and voltage (6-18S).
  • Dimensions: The motor has a diameter and length of 70mm each, which is important for fitting into your build.

Frequently Asked Questions (FAQ)

Q: What's the size of this motor?
A: The diameter and length of the motor are 70mm and 70mm respectively.
Q: What's the maximum power of this motor?
A: The maximum power is 4200W.
Q: What's the maximum current?
A: The maximum current is 100A.
Q: What is the motor structure?
A: It has a motor structure of 12N/14P.

Warranty and Support

Warranty Policy

The warranty period for consumable electronic products, including this motor, is 2 months from the 7th day after shipment (the shipping date is checked by logistic record).

Conditions Not Covered by Warranty:

  • Lack of purchase channel source proof.
  • Mechanical damage to electronic components or PCB.
  • PCB board repair involving soldering iron traces (excluding soldering the cable bullet connectors).
  • Water damage or external impact damage.
  • Damage from abnormal applications beyond the product specifications.

Important Notes:

  • All motors are 100% tested and shipped as good products.
  • No warranty is provided if the damage exceeds the original purchase price of the product.
  • The buyer is responsible for shipping costs related to warranty claims.

Contact Support

For any warranty claims or technical support, please contact Flipsky service at: flipsky_service@outlook.com. Please provide your original order number or personal card number (only in group buy products) to verify your purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.