KALADA LED 18 in 1 light strip

Contents

KALADA Car Atmosphere Interior LED Ambient Lights Instruction Manual

Model: LED 18 in 1 light strip

1. Product Information

Product Name: Car Atmosphere Interior LED Ambient Lights

Brand: KALADA

Model Name: LED 18 in 1 light strip

Batch/Serial Number: 050226-1

This product is designed to enhance your car's interior ambiance with customizable RGB lighting. It features flexible fiber optic light strips and multiple control options.

2. Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: To avoid danger of suffocation, keep this bag away from babies and children. Do not use this bag in cribs, beds, carriages, or play pens. This bag is not a toy.

This product must comply with all applicable safety and regulatory requirements in the market where it is sold.

3. Setup Instructions

3.1 Package Contents

The kit includes the following components, depending on the chosen item type:

  • Main Controller Module: 1 unit
  • Sub-controller Modules: 4 units
  • LED Light Strips: Various lengths (e.g., 35cm, 75cm, 110cm) and quantities depending on the kit (6-in-1, 10-in-1, 14-in-1, 18-in-1, 22-in-1).
  • Power Cables: For main and sub-controllers.
  • Extension Wire: 1 unit (200cm)
  • Host Power Cord/Touch Button: 1 unit (101.5cm)
  • Auxiliary Power Cord: 4 units (56cm)
  • Foot Well Lamps: 4 units (for 10-in-1 and higher kits)
  • Door Light / Central Control Light: 4 units (for 14-in-1 and higher kits)
  • Dedicated Stickers for Cars
Product components and installed car interior ambient lighting
Overview of product components and an installed view of the ambient lighting.
Detailed component breakdown for the 18-in-1 kit
Detailed breakdown of components for the 18-in-1 kit, including light strips, controllers, and wiring.
Detailed component breakdown for the 6-in-1 kit
Detailed breakdown of components for the 6-in-1 kit, showing main controller, sub-controllers, light strips, and power wires.

3.2 Pre-Installation Steps

  1. Distinguish Main and Sub-modules: The module with a QR Code is the main control unit. It projects signals and synchronously controls all sub-modules. The other modules are sub-modules, which receive instructions from the main module.
  2. Test the Product: After receiving the product, connect it to the car battery (do not use an external power supply) to ensure all components are working correctly before proceeding with installation.
  3. Download the Application: Scan the QR code on the main control box to download the control application. Turn on Bluetooth on your mobile device; the app should connect automatically (Android systems may require location services to be enabled).

3.3 Power Connection

The system operates on a wide voltage range of 5V-14V, compatible with most 12V car systems.

Comparison of upgraded controller with 5-14V input and longer lifespan versus ordinary 12V controller
Comparison highlighting the upgraded controller's wider voltage range (5-14V) and extended lifespan.
  • Main Controller:
    • Connect the Red wire to ACC power or a cigarette lighter fuse (positive polarity, 5A-15A current). Avoid sensor interfaces.
    • Connect the Black wire to any ground metal on the car chassis.
  • Sub-controllers:
    • Connect sub-controllers to the door constant power supply.
    • Testing Door Panel Power Supply:
      • Constant Power: If the door has an automatic window closed function when the car is off, or if the window lifter can move up/down without igniting the car, it's constant power.
      • ACC Power: If door functions are not available until the car is ignited, it's ACC power.
    • For ACC Power Doors (e.g., Japanese/Korean cars):
      • Ignite the car before testing positive and negative poles.
      • Find a positive pole (6-18V available, thick wire) and a negative pole (not from door iron/screws).
      • Connect the sub-control module and test window lifter operation. If the light goes off or flashes, the power supply is unstable; find workable positive wires.
    • For Constant Power Doors (e.g., German cars):
      • Ignite the car before testing positive and negative poles.
      • Find a positive pole (6-18V available, thick wire) and a negative pole (not from door iron/screws).
      • Connect the sub-control module and test window lifter operation. If the light goes off or flashes, the power supply is unstable; find workable positive wires.

3.4 Light Strip Installation

Diagram showing luminous position display for ambient lights in a car interior
Diagram illustrating typical installation points for ambient lighting, including door, central control, footwell, and storage box.
  • Central Console:
    • Remove the trim panel.
    • Thread light strip wires through holes in the trim panel and connect to the main module.
    • Secure the light strip to the trim board with 3M tape and cut off excess.
    • Reinstall the trim panel.
  • Door Panel:
    • Remove the door panel and its trim panel screws.
    • Run the acrylic light strip from the back of the door panel through the trim panel hole to the front.
    • Fasten the light strip to the decorative board with 3M tape.
    • Install the trim panel and connect light strip wires to the sub-module.
    • Reinstall the door panel.

3.5 Post-Installation Test

After installing all components, set all lights to white color mode and test for 5-10 minutes. Move the window lifter to observe if the ambient light goes off or flashes. Ensure there are no issues before finalizing the installation.

4. Operating Instructions

4.1 Control Methods

The ambient lights can be controlled via two methods:

  1. Double Button Mode: Use the physical buttons for basic control.
  2. Mobile Phone APP Control: Connect via Bluetooth to the dedicated mobile application for advanced features.
Mobile phone app interface for Bluetooth control of car ambient lights
The mobile application allows for Bluetooth control, offering color transformation, multiple modes, music mode, microphone mode, and timing mode.

4.2 Light Modes and Features

The system offers a variety of lighting modes to customize your car's interior ambiance:

  • Breathe Mode: Lights gently fade in and out.
  • Gradient Mode: Colors smoothly transition from one to another.
  • Cycle Mode: Lights cycle through a predefined sequence of colors.
  • Strobe Mode: Lights flash rapidly.
  • Music Rhythm Mode: Equipped with sound sensors, the LED lights synchronize with musical rhythm, adjusting flicker to sound intensity.
  • Flow Mode: Lights create a flowing effect.
  • Running Water Mode: Lights simulate a running water effect.
  • Sleep Mode: Automatically changes to a dark brightness to provide a relaxing atmosphere.
  • Brightness & Color Temperature Adjustment: Adjust the light intensity and color temperature to your preference.
Illustration of brightness adjustment from 10% to 100%
Brightness can be adjusted freely from low light (10%) to high brightness (100%).
Video demonstrating the dynamic color effects and installation of the ambient lighting system in a car interior.

5. Maintenance

  • Storage: After use, turn off the device and store it in a dry place, away from children.
  • Cleaning: Use a soft, dry cloth to clean the light strips and control modules. Avoid using harsh chemicals or abrasive materials.
  • Inspection: Periodically inspect all connections and light strips for any signs of wear or damage. Replace any damaged components immediately.

6. Troubleshooting

  • Lights not working after installation: If the lights do not work, remove the kit and connect it directly to the car battery for testing. If the lights work, the issue is likely an installation error. If they still do not work, it indicates a product fault.
  • Lights flashing or going off when windows are lifted: This indicates an unstable power supply. Recheck the positive wires for sub-controllers and find a more stable connection.
  • App connection issues: If the app cannot find the LEDs after reinstallation or crashing, try resetting the main controller by disconnecting and reconnecting its power. Ensure Bluetooth is enabled and, for Android, location services are active.
  • Light strips too long: The fiber optic light strips can be cut to desired lengths. Refer to the 'User Tips' section for more details.

7. Specifications

FeatureSpecification
Brand NameKALADA
Model NameLED 18 in 1 light strip
Item TypeAtmosphere lamp
Voltage5V - 14V (compatible with all 12V cars)
Power5-10W
Special FeaturesFlexible, Symphony, High Brightness
MaterialAcrylic
Lifespan>100,000 hours
CertificationCE
Item Weight0.8 kg
Light Strip Lengths35cm, 75cm, 110cm (various combinations per kit)
Package Dimensions (approx.)Length: 30cm, Width: 20cm, Height: 6cm
CE Certificate of Conformity for the car ambient light product
CE Certificate of Conformity, issued by Shenzhen EZT Testing Technology Co., Ltd.

8. Warranty & Support

This product comes with a 12-month warranty, with parts replacement available. For any product faults or issues not resolved by troubleshooting, please contact customer support.

Manufacturer: Guangzhou Pengzhan Optoelectronics Technology Co., Ltd.

Address: Room 201, 2nd Floor, Huanbao Industrial Park, No. 1-2, Huanbao 2nd Road, Xintang Town, Zengcheng District, Guangzhou, China

Email: 690856574@qq.com

EU Authorized Representative: MJCM SARL

Address: 78 avenue des Champs Elysees Bureau 326, PARIS, FR

Email: mjcm190928@gmail.com

For a detailed user manual in PDF format, please refer to the official document: User manual (PDF)

9. User Tips

  • Customizable Installation: Each controller has 4 connection ports, allowing users to customize the position of each light according to their preference.
  • Trimming Light Strips: The ultra-thin fiber optic light strips are flexible and can be cut to the desired length to fit various car interior contours.
  • Illustration showing the flexibility and cutability of the light strips
    The LED lamp beads material is flexible and can be bent arbitrarily, and the strips can be cut.
  • Start-up Animation: The product features a 7-second start-up animation (welcome light) which can be optionally closed.
  • Wide Compatibility: The system is designed to be compatible with over 99% of car models, including BMW, Audi, Benz, Hyundai, Toyota, Honda, Buick, Ford, Tesla, Lexus, Volvo, Peugeot, Renault, Suzuki, and Kia.
  • Individual Zone Control: The app may allow for individual zone adjustments, such as turning off specific lights like footwell lights, depending on the kit configuration and app features.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.