1. Introduction
This manual provides instructions for the installation, operation, and maintenance of the JACK JK-900E/904E series wire accept sensors for industrial overlock sewing machines. These sensors are critical components for ensuring the precise function of your sewing equipment. Please read this manual thoroughly before installation and use.

2. Setup and Installation
Proper installation is crucial for the correct functioning of the sensor and the sewing machine. Always ensure the machine is powered off and disconnected from the power source before beginning any installation or maintenance.
2.1 Identifying Sensor Types
The JACK JK-900E/904E series uses various wire accept sensors, each designated by a letter (D, E, H, G, BG). Identify the specific sensor required for your machine's needs by checking the label on the sensor wire and comparing it with the images below.





2.2 Installation Steps
- Power Off: Ensure the sewing machine is completely powered off and unplugged from the electrical outlet.
- Locate Installation Point: Refer to your specific JACK JK-900E/904E sewing machine's service manual to locate the correct installation point for the sensor you are replacing or installing. Each sensor type (D, E, H, G, BG) has a designated position.
- Remove Old Sensor (if applicable): Carefully disconnect the old sensor's wiring and unmount it from the machine. Note the orientation and connection points.
- Mount New Sensor: Position the new sensor in the designated location. Ensure it is securely mounted and aligned correctly according to your machine's manual.
- Connect Wiring: Connect the sensor's wire to the corresponding port on the sewing machine's control board or wiring harness. Ensure the connectors are fully seated and secure.
- Secure Wires: Route and secure the sensor wires to prevent them from interfering with moving parts of the machine.
- Initial Check: Before powering on, visually inspect all connections and mounting points to ensure everything is correctly installed.
3. Operating the Sensor (Indirect)
These wire accept sensors are integral components that enable the proper functioning of your JACK JK-900E/904E overlock sewing machine. They do not have direct user controls but contribute to the machine's automated processes.
- Once correctly installed, the sensor will automatically detect the presence or position of the wire/thread as designed by the sewing machine's manufacturer.
- The machine's control system will interpret the sensor's signals to perform specific functions related to overlock stitching.
- Ensure that the area around the sensor is clear of obstructions during machine operation to allow for accurate readings.
4. Maintenance
Regular maintenance helps prolong the life of your sensors and ensures consistent machine performance.
- Cleaning: Periodically clean the sensor surface and surrounding area to remove lint, dust, and debris that can accumulate during sewing operations. Use a soft brush or compressed air. Avoid using harsh chemicals that could damage the sensor material.
- Wire Inspection: Regularly inspect the sensor wires for any signs of wear, fraying, cuts, or damage. Damaged wires can lead to intermittent operation or complete failure. Replace damaged wires immediately.
- Connection Check: Ensure all electrical connections to the sensor remain secure. Loose connections can cause erratic behavior.
- Environmental Conditions: Operate the sewing machine in a clean, dry environment to prevent moisture or excessive dust from affecting sensor performance.
5. Troubleshooting
If you experience issues after installing or using the sensor, consider the following troubleshooting steps:
- Machine Not Functioning: If the sewing machine does not operate correctly after sensor installation, first verify that the machine is powered on and all safety switches are engaged.
- Incorrect Sensor Type: Double-check that the correct sensor type (D, E, H, G, or BG) has been installed for the specific function required by your machine model. Refer to your machine's service manual.
- Loose Connections: Ensure all sensor wiring connections are firm and properly seated. Disconnect and reconnect if necessary.
- Obstructions: Check for any lint, thread, or other debris obstructing the sensor's path or surface. Clean as described in the Maintenance section.
- Sensor Damage: Inspect the sensor for any visible physical damage. A damaged sensor will need to be replaced.
- Machine Error Codes: If your sewing machine displays an error code, consult your machine's main user manual or service manual for specific troubleshooting steps related to sensor errors.
6. Specifications
| Feature | Detail |
|---|---|
| Product Type | Wire Accept Sensor |
| Compatibility | JACK JK-900E, JACK JK-904E Industrial Overlock Sewing Machines |
| Stitch Formation | Overlock Stitch |
| Sensor Types | D (Rear Receiving), E (Front Receiving), H (Third Receiving), G (Third Transmitting), BG (Third Transmitting) |
| Origin | Mainland China |
| Approximate Package Length | 10 cm |
| Approximate Package Width | 6 cm |
| Approximate Package Height | 8 cm |
| Approximate Package Weight | 0.1 kg |
7. User Tips
- Verify Compatibility: Before purchasing or installing, always confirm that the specific sensor type (D, E, H, G, or BG) is compatible with your exact JACK JK-900E or JK-904E model. While these sensors are designed for the series, specific sub-models might have unique requirements. For example, compatibility with models like JK-905E should be verified with the machine manufacturer or seller.
- Consult Machine Manual: For detailed wiring diagrams and precise installation locations, always refer to the official service or user manual for your JACK JK-900E/904E sewing machine.
- Handle with Care: Sensors are delicate electronic components. Avoid dropping them or applying excessive force during installation.
8. Warranty and Support
For information regarding product warranty, returns, or technical support, please contact the seller directly. The seller, YURI sewing-machine parts Store, can provide assistance with product-specific inquiries and support.