DAHAO EF120 Series

Contents

DAHAO EF120 Series Alarm Board / Thread Break Detecting Board User Manual

For Industrial Computer Embroidery Machines

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of the DAHAO EF120 series Alarm Board / Thread Break Detecting Board. This component is designed specifically for industrial computer embroidery machines to detect thread breaks during operation and trigger an alarm or machine stop, ensuring efficient and error-free embroidery processes.

DAHAO EF120 Series Alarm Board

Figure 1: Example of a DAHAO EF120 Series Alarm Board. Note that specific board layouts and markings may vary by model.

Important: This product is intended for use only with industrial sewing machines. It is not compatible with other machine types.

2. Setup and Installation

Installation of the DAHAO EF120 series board requires technical expertise and should ideally be performed by a qualified technician. Incorrect installation can damage the board or the embroidery machine.

2.1 Compatibility Check

Before installation, it is crucial to verify the compatibility of the board with your embroidery machine. The part number of the replacement board must exactly match the part number of the original board being replaced. Boards with different part numbers are not interchangeable.

  • Verify Part Numbers: Carefully compare the part number printed on your existing board with the part number of the new board.
  • Consult if Unsure: If you are uncertain about compatibility, it is strongly recommended to contact the seller or a qualified technician. You may need to provide detailed photographs of your machine, including the motor, barcodes, machine model, electric cabinet, and interface connections, for verification.

2.2 Installation Steps (General Guidance)

These steps are general guidelines. Always refer to your embroidery machine's service manual for specific instructions.

  1. Power Off: Ensure the embroidery machine is completely powered off and unplugged from the power source to prevent electrical shock or damage.
  2. Access Control Panel: Carefully open the machine's control panel or housing to access the existing alarm/thread break detection board.
  3. Disconnect Old Board: Document the wiring connections (e.g., take photos) before carefully disconnecting all cables and removing the old board.
  4. Inspect New Board: Before installing, visually inspect the new board for any signs of damage, dust, or oxidation that may have occurred during storage. Clean gently with a soft, dry brush if necessary.
  5. Install New Board: Position the new DAHAO EF120 series board in the designated slot and secure it.
  6. Reconnect Wiring: Carefully reconnect all wiring and connectors to the new board, ensuring they match the documented configuration.
  7. Close Panel: Securely close the machine's control panel or housing.
  8. Initial Power-Up: Plug in the machine and power it on. Observe for any error messages or unusual behavior.

Warning: Improper handling or installation can lead to permanent damage to the board or the embroidery machine. Seek professional assistance if you are not confident in performing the installation.

3. Operating Instructions

The DAHAO EF120 series Alarm Board / Thread Break Detecting Board operates automatically once correctly installed and the embroidery machine is powered on. Its primary function is to monitor thread tension and movement to detect thread breaks.

  • Automatic Detection: The board continuously monitors the embroidery process for thread breaks.
  • Alarm/Stop Function: Upon detecting a thread break, the board will trigger an alarm (audible or visual, depending on machine configuration) and/or automatically stop the embroidery machine to prevent further errors or damage to the workpiece.
  • Machine Interface: The board integrates with the embroidery machine's control system. Refer to your embroidery machine's user manual for specific details on how thread break alarms are displayed and how to reset the machine after a thread break.

No direct user interaction with the board itself is required during normal operation.

4. Maintenance

The DAHAO EF120 series board is a robust electronic component designed for long-term reliability with minimal maintenance. However, adhering to basic care practices can extend its lifespan.

  • Keep Clean: Ensure the interior of the embroidery machine's control panel remains free from dust, lint, and debris. Dust accumulation can lead to overheating or short circuits. Use compressed air or a soft brush to gently clean the board and surrounding areas periodically.
  • Maintain Dry Environment: Protect the board from moisture and humidity. Operate the embroidery machine in a dry environment to prevent corrosion and electrical malfunctions.
  • Avoid Physical Shock: Handle the board with care during installation or any machine servicing. Avoid dropping or subjecting it to physical impact.
  • Regular Machine Servicing: Ensure your embroidery machine undergoes regular professional servicing, which includes checking internal electronic components.

5. Troubleshooting

If you experience issues with the thread break detection system after installing the DAHAO EF120 series board, consider the following troubleshooting steps:

5.1 Common Issues and Solutions

ProblemPossible CauseSolution
Thread break not detected / Machine not stopping
  • Incorrect board installed (part number mismatch)
  • Loose or incorrect wiring connections
  • Board malfunction
  • Sensor issue (not board related)
  • Verify board part number matches original.
  • Check all wiring connections for security and correctness.
  • Ensure board is properly seated.
  • Consult machine service manual for sensor diagnostics.
Constant thread break alarm / Machine stops immediately
  • Incorrect board installed
  • Faulty wiring
  • Board malfunction
  • Sensor issue (e.g., blocked, faulty)
  • Verify board part number.
  • Check wiring for shorts or incorrect connections.
  • Inspect thread path and sensors for obstructions.
  • If problem persists, professional diagnosis is required.
Machine not powering on after board installation
  • Incorrect wiring
  • Short circuit
  • Damage during installation
  • Immediately power off and unplug the machine.
  • Re-check all wiring connections meticulously.
  • If unsure, remove the new board and test if the machine powers on without it (if safe to do so).
  • Seek professional assistance.

Note: Due to the technical nature of this component, if basic troubleshooting does not resolve the issue, professional diagnosis and repair are recommended.

6. Specifications

FeatureDetail
Product TypeAlarm Board / Thread Break Detecting Board
BrandDAHAO
Model SeriesEF120, EF120A, EF120B, EF120F, EF120K, EF120MW
MaterialPlastic (Circuit Board)
UseComputer Embroidery Machines (Industrial)
OriginMainland China
Typical Part Numbers (Examples)P/N EF120F-L 2008.11.18, P/N EF120W 1605, P/N EF120F-130Z 2008.11.18 (Note: Part numbers vary by specific model and revision)
Dimensions (Approximate, for EF120W)107mm x 73mm (4.2 x 2.9 inches)

Note on Variations: Due to product updates and different models within the EF120 series, the physical appearance and exact component layout of the circuit board may vary. Always rely on the specific part number for compatibility.

7. User Tips

  • Verify Part Numbers Diligently: The most critical step for successful replacement is ensuring the new board's part number precisely matches the old one. Double-check before purchase and installation.
  • Professional Installation Recommended: Given the technical nature of this component and its integration into complex machinery, professional installation by an experienced technician is highly recommended to avoid damage and ensure proper function.
  • Document Before Disassembly: Always take clear photos of wiring and component placement before disconnecting anything. This serves as a valuable reference during reassembly.

No specific user tips were available from customer reviews or Q&A for this product.

8. Warranty and Support

Please note the following regarding warranty and support for this product:

  • No Returns or Refunds: All sales of this product are final. The seller explicitly states that once sold, items are not refundable, and returns or disputes based on "no reason" are not accepted.
  • Pre-Purchase Compatibility Support: Support is primarily available for pre-purchase inquiries regarding product compatibility. If you are unsure whether the board is suitable for your machine, contact the seller with detailed machine information (photos of machine, motor, barcodes, model, electric cabinet, interfaces) for confirmation before placing an order.
  • No Explicit Warranty: No explicit warranty period or terms are provided for this product. Buyers should be aware of the "no returns, no refunds" policy.

It is the buyer's responsibility to ensure compatibility and suitability before purchase, as post-sale support for issues not related to initial compatibility may be limited.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.