Flipsky Dual 75100

Contents

Flipsky Dual 75100 VESC Speed Controller Instruction Manual

Model: Dual 75100 | Brand: Flipsky

Introduction

This manual provides essential information for the safe and effective use of your Flipsky Dual 75100 Speed Controller. Designed for electric skateboards, scooters, and ebikes, this VESC-based controller offers robust performance and advanced control capabilities. Please read this manual thoroughly before installation and operation.

Flipsky Dual 75100 Speed Controller with cables
Figure 1: The Flipsky Dual 75100 Speed Controller, showcasing its compact design and multiple connection points.

Specifications

FeatureDetail
SizeL107mm x W103mm x H18.5mm
Voltage14-84V (4-20S safety)
CurrentContinuous max 100A single, dual continuous max 200A (values depend on mounting and ambient temperature)
BEC5V@1A
Control ModesBLDC square wave mode, FOC sine wave mode
FirmwareLatest (firmware update supported)
ERPM150000
Control Interface PortsUSB, CAN, UART
Supported SensorsABI, HALL, AS5047, AS5048A
Input Set SupportPPM, ADC, NRF, UART
Wire Size12AWG
ProgrammableYes
Regenerative CapacityYes
MaterialComposite Material
OriginMainland China
Recommended Age14+ years
UseVehicles & Remote Control Toys (Cars, Electric Skateboard, Scooter, Ebike)
CertificationCE, RoHS
Dimensions of Flipsky Dual 75100 Speed Controller
Figure 2: Physical dimensions of the Dual FSESC75100 controller. Length: 107mm, Width: 103mm, Height: 18.5mm.

Setup and Wiring

Proper wiring is crucial for the functionality and safety of your speed controller. Refer to the detailed wiring diagram below for all connections.

Detailed wiring diagram for Flipsky Dual 75100 Speed Controller
Figure 3: Detailed wiring diagram for the Dual FSESC75100. This diagram illustrates connections for motors, battery, and various control interfaces including HALL, UART2, COMM, SWD, CAN, PPM, and USB ports. Ensure connectors are unplugged carefully to avoid damage.

Connection Points:

  • Motor Connections: Connect motors to the designated outputs. Note the Red/Green LED indicators for each motor.
  • Battery Connection: Connect your battery to the main power input.
  • Control Interfaces:
    • HALL (1, 8): For Hall sensors.
    • UART2 (2, 9): Universal Asynchronous Receiver-Transmitter.
    • COMM (3, 10): Communication port.
    • SWD (4, 11): Serial Wire Debug.
    • CAN (5, 12): Controller Area Network.
    • PPM (6, 13): Pulse Position Modulation.
    • USB (7, 14): For configuration and firmware updates.

Important: When unplugging connectors, please press the release mechanism to avoid damaging wires and connectors.

Operation

The Flipsky Dual 75100 supports both BLDC square wave mode and FOC sine wave mode for motor control. The choice of mode depends on your motor type and desired performance characteristics. Firmware updates are supported to ensure optimal performance and access to new features.

Firmware and Configuration:

The controller is compatible with VESC_TOOL for configuration and firmware management. Always ensure you are using the latest firmware version for best compatibility and performance.

Maintenance

To ensure the longevity and reliable operation of your Flipsky Dual 75100 speed controller, follow these general maintenance guidelines:

  • Keep Clean: Regularly inspect the controller for dust, dirt, or debris. Clean gently with a soft, dry brush or compressed air.
  • Environmental Protection: Avoid exposing the controller to excessive moisture, extreme temperatures, or corrosive environments.
  • Connection Integrity: Periodically check all wire connections for secure fitment and signs of wear or damage. Loose connections can lead to intermittent operation or component failure.
  • Temperature Management: Ensure adequate airflow around the device, especially during high-current operation, as performance values depend on ambient temperature and mounting.

Troubleshooting

Phase Filtering Issue:

Critical Warning: Phase filtering is not available for Flipsky ESC75100 and 75200!

If you are using firmware version 5.3 (VESC_TOOL 3.01) or above, you MUST turn off the phase filter function. In VESC_TOOL, select "false" for this setting. Failure to disable the phase filter will result in ESC damage. Do not restore default parameters when using the wizard interface if you have made this change.

For further guidance, refer to the following resources:

General Troubleshooting Tips:

  • No Power: Check battery connections and ensure the battery is charged. Verify all power wires are securely connected.
  • Motor Not Spinning: Confirm motor phase wire connections and Hall sensor connections (if used). Check VESC_TOOL for motor detection and configuration errors.
  • Intermittent Operation: Inspect all signal and power cables for loose connections or damage. Ensure the controller is not overheating.

User Tips

  • Always perform a motor detection in VESC_TOOL after any changes to motor or battery configuration.
  • Regularly check for firmware updates from Flipsky to benefit from performance improvements and bug fixes.
  • When configuring with VESC_TOOL, save your settings before making significant changes, and avoid restoring default parameters if you have specific configurations like the phase filter setting.

Warranty and Support

The warranty period for consumable electronic products (e.g., VESC/Motor/Battery) is generally 2 months since the 7th day after shipment (the shipping date is checked by logistic record).

For non-electronic products, the warranty period is 2 months since the 7th day after shipment (the shipping date is checked by logistic record). You can return it to us for free repair or replacement when we get it and analyzed it as a manufacturing failure. We will bear the return back to you shipping cost only. If the replacement or repair is not possible for you, a discount can be provided for the new replacement (excludes the shipping cost). The wear and tear caused by normal use is not considered to be a defect product.

Conditions Not Covered by Warranty:

  • Purchase through non-official channels.
  • Mechanical damage to electronic components or PCB.
  • PCB board has repair soldering iron traces (excluding solder the cable bullet connectors).
  • Wire damage or external impact damage.
  • Non-waterproof products: water inflow.
  • Abnormal applications beyond the product specifications.

Most products are tested before shipment, especially the VESC and motors are 100% tested and shipped as a good product before shipment. Any uncertain connection or information for VESC/Motors settings, please contact us before your installation.

No term warranty, in no case shall Flipsky's liability be greater than the actual purchase price of the product.

We're willing to provide repair service for reasonable charge if your product is out of warranty, while the service excludes both side's shipping cost.

This updated warranty policy is valid since 2018/11/2, and the previous ordered products before 2018/11/1 still follow the policy before updates.

For support, please contact Flipsky customer service via email: service@outlook.com.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.