SINOTIMER XY-501

Contents

SINOTIMER XY-501 Series PID Temperature Controller User Manual

Model: XY-501, XY-504, XY-507, XY-509

1. Introduction

The SINOTIMER XY-501 series is a versatile digital PID temperature controller designed for precise temperature management in various industrial and commercial applications. This controller features a dual display for process value (PV) and set value (SV) in Celsius, supporting a wide range of thermocouple and RTD inputs. It offers both Relay and Solid State Relay (SSR) output options, along with a single alarm output for enhanced control and safety. Constructed from high-quality flame-retardant material, it ensures durability and reliable performance.

Front view of SINOTIMER XY-501 PID Temperature Controller

Figure 1: Front view of the SINOTIMER XY-501 PID Temperature Controller.

2. Key Features

  • Dual Digital Display: Simultaneous display of Process Value (PV) and Set Value (SV) in Celsius (°C).
  • Universal Input: Supports multiple thermocouple types (K, J, S, E, R, B, N, T) and RTD sensors (PT100, Cu50).
  • Flexible Output: Configurable for Relay or Solid State Relay (SSR) control output.
  • Single Alarm Output: Provides an alarm signal (ALM1) for critical temperature deviations.
  • Wide Power Supply: Operates on 100-240VAC, 50/60Hz.
  • Durable Construction: Made from high-quality flame-retardant material, offering anti-broken, anti-oxidant, and anti-scratch properties.
  • PID Control: Advanced PID algorithm for precise and stable temperature control.

3. Specifications

ParameterSpecification
Model NumberXY-501 (Series includes XY-504, XY-507, XY-509)
Brand NameSINOTIMER
TheoryTemperature Controller (PID)
Display TypeDIGITAL (Dual Display)
Display UnitCelsius (°C)
Power TypeCharger (100-240VAC, 50/60Hz)
Power Consumption5VA
CertificationCE
Max Measuring Temperature120°C & Above (up to 1300°C depending on sensor)
Measure TypeK, J, S, E, R, B, N, T (Thermocouple), PT100, Cu50 (RTD)
Control OutputRelay / SSR
Alarm OutputALM1
Accuracy±0.5%
Ambient Temperature50°C Max
Display Size1.9 Inches & Under
StyleStanding Station
UseIndustrial
Battery IncludedNo
Is Smart DeviceNo
Dimensions (XY-501)48*48*78MM
Dimensions (XY-504)48-86*78MM
Dimensions (XY-507)72*72*78MM
Dimensions (XY-509)96*96*78MM

4. Package Contents

Upon opening your package, please ensure all items are present and in good condition:

  • 1 x PID Digital Temperature Controller (Thermocouple/RTD sensor NOT included)
  • 1 x English User Manual

5. Safety Information

Please read and understand all safety instructions before installation and operation. Failure to follow these instructions may result in equipment damage, personal injury, or death.

  • Always disconnect power before performing any wiring or maintenance.
  • Ensure wiring is performed by a qualified electrician and complies with local electrical codes.
  • Do not operate the device in environments exceeding the specified ambient temperature (50°C Max).
  • Protect the device from moisture, dust, and corrosive gases.
  • Use appropriate personal protective equipment (PPE) when working with electrical systems.

6. Installation and Wiring

The controller is designed for panel mounting. Ensure adequate space for ventilation and wiring connections. Refer to the specific wiring diagram for your model (XY-501, XY-504, XY-507, XY-509) as terminal configurations may vary slightly.

6.1. Wiring Diagrams

Below are typical wiring diagrams for the XY-501 series. Always verify the diagram printed on your specific unit for accurate connections.

Wiring diagram for SINOTIMER XY-501 PID Temperature Controller

Figure 2: Wiring Diagram for Model XY-501. Terminals 1-2 for AC power (100-240V), 3-4 for SSR output, 5-6 for Relay output, 7-8 for ALM1, 9-10 for RTD input, 11-12 for Thermocouple input.

Wiring diagram for SINOTIMER XY-504 PID Temperature Controller

Figure 3: Wiring Diagram for Model XY-504. Terminals 1-2 for AC power (100-240V), 3-4 for SSR output, 5-6 for Relay output, 7-8 for ALM1 (NO), 9-10 for ALM1 (NC), 11-12 for RTD input, 13-14 for Thermocouple input.

Wiring diagram for SINOTIMER XY-507 PID Temperature Controller

Figure 4: Wiring Diagram for Model XY-507. Terminals 1-2 for AC power (100-240V), 3-4 for SSR output, 5-6 for Relay output, 7-8 for ALM1 (NO), 9-10 for ALM1 (NC), 11-12 for RTD input, 13-14 for Thermocouple input.

Wiring diagram for SINOTIMER XY-509 PID Temperature Controller

Figure 5: Wiring Diagram for Model XY-509. Terminals 1-2 for AC power (100-240V), 3-4 for SSR output, 5-6 for Relay output, 7-8 for ALM1 (NO), 9-10 for ALM1 (NC), 11-12 for RTD input, 13-14 for Thermocouple input.

6.2. Connection Guidelines

  • Power Supply: Connect the 100-240VAC, 50/60Hz power supply to the designated AC terminals (typically 1 and 2).
  • Input Sensor: Connect your thermocouple (K, J, etc.) or RTD (PT100, Cu50) sensor to the INPUT terminals. Ensure correct polarity for thermocouples.
  • Control Output: Connect your heating or cooling device to either the Relay output or SSR output terminals, depending on your application and the type of load.
  • Alarm Output: Connect external alarm devices to the ALM1 terminals if alarm functionality is required.

7. Operating Instructions

The SINOTIMER PID temperature controller features a user-friendly interface with a SET button, R/S (Reset/Shift) button, and Up/Down arrow buttons for navigation and parameter adjustment.

7.1. Basic Operation

  • Power On: Once wired correctly, apply power. The controller will perform a self-test and then display the current Process Value (PV) and Set Value (SV).
  • Viewing PV/SV: The upper display (PV) shows the current measured temperature. The lower display (SV) shows the target temperature.

7.2. Setting the Target Temperature (SV)

  1. Press the SET button once. The SV display will start flashing.
  2. Use the Up (▲) and Down (▼) arrow buttons to adjust the target temperature.
  3. Press SET again to confirm the new SV and exit the setting mode.

7.3. Accessing Parameter Settings

To access advanced parameters for PID tuning, input type selection, alarm settings, etc., a longer press of the SET button is usually required. The specific sequence and parameter codes will be detailed in the full English User Manual included with your product. Generally:

  1. Press and hold the SET button for approximately 3-5 seconds to enter the parameter menu.
  2. Use the SET button to cycle through different parameters.
  3. Use the Up (▲) and Down (▼) arrow buttons to change the value of the selected parameter.
  4. Press and hold SET again for 3-5 seconds to save changes and exit, or wait for the controller to automatically exit after a period of inactivity.

7.4. Video Demonstration

Video 1: A short demonstration of the SINOTIMER XY-501 series temperature controller's display and basic interaction.

8. Maintenance

To ensure the longevity and accurate performance of your temperature controller, follow these maintenance guidelines:

  • Cleaning: Regularly wipe the display and casing with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Environmental Conditions: Keep the controller in a clean, dry environment, free from excessive dust, moisture, and corrosive substances.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
  • Sensor Inspection: Inspect the temperature sensor (thermocouple or RTD) for any signs of damage or wear, especially if operating in harsh conditions. Replace if necessary.

9. Troubleshooting

If you encounter issues with your SINOTIMER PID temperature controller, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No display/Power offNo power supply or incorrect wiring.Check power connections (100-240VAC). Ensure power is supplied to terminals 1 and 2.
PV display shows 'HHHH' or 'LLLL'Sensor open circuit, short circuit, or incorrect input type setting.Check sensor wiring and connections. Verify the input type setting in the parameter menu matches your sensor.
Temperature reading is inaccurateIncorrect sensor type selected, sensor calibration error, or sensor damage.Confirm correct input type. Check sensor for damage. Perform sensor calibration if available in the manual.
Output not activating (heating/cooling)SV not set correctly, output mode incorrect, or faulty output wiring/device.Verify SV is set to desired temperature. Check output mode (Relay/SSR) and wiring to the load. Test the load device independently.
Alarm not triggeringAlarm parameters not set correctly, or alarm device faulty.Check alarm type and setpoint in the parameter menu. Ensure the external alarm device is functioning and wired correctly.

For more detailed troubleshooting, please refer to the comprehensive user manual provided with your product.

10. User Tips

  • High Temperature Applications: This controller is suitable for high-temperature applications, capable of working with sensors up to 1300°C (e.g., K-type thermocouples). Ensure your chosen thermocouple or RTD sensor is rated for the desired temperature range.
  • Sensor Compatibility: The controller supports a wide range of thermocouple types (K, J, S, E, R, B, N, T) and RTD sensors (PT100, Cu50). Always select the correct input type in the controller's settings to match your connected sensor for accurate readings.
  • PID Tuning: For optimal performance, especially in critical applications, consider performing a PID auto-tuning process after initial setup. This helps the controller learn the characteristics of your specific heating/cooling system. Refer to the full manual for auto-tuning instructions.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.