Estardyn TFT Display 0.96/1.3/1.44/1.77/1.8/2.0 inch LCD

Contents

Estardyn TFT LCD Display Module User Manual

Models: 0.96, 1.3, 1.44, 1.77, 1.8, 2.0 inch IPS Full Color LCD

1. Introduction

This manual provides detailed instructions for the Estardyn TFT LCD Display Modules, designed for use with microcontrollers like Arduino. These full-color IPS displays are available in various sizes and utilize a Serial Peripheral Interface (SPI) for communication, making them suitable for a wide range of embedded projects requiring graphical output.

Assortment of Estardyn TFT LCD modules in various sizes
Figure 1: Assortment of Estardyn TFT LCD Display Modules.

2. Specifications

The Estardyn TFT LCD modules come in several sizes, each with specific characteristics. Common features include 65K color display and SPI interface. Detailed specifications for each variant are provided below.

2.1 General Specifications

FeatureDescription
Display ModeNormally black IPS
Color DepthRGB 65K color
Input DataSPI interface (4-wire)
Viewing DirectionAll View
Logic IO Port Voltage3.3V (TTL)

2.2 Module Specific Specifications

0.96 inch TFT Module

ItemValue
Size0.96 inch
Display FormatGraphic 80RGB*160 Dot-matrix
Drive ICST7735S
Dimensional Outline24(W)*30 (H)*2.8+/-0.1(T)mm
Resolution80RGB*160 Dots
LCD Active Area10.8 (W)*21.7 (H)mm
Dot Pitch0.135(H) x 0.1356(V) mm
Operating Temperature-20~70°C
Front view of 0.96 inch TFT LCD module
Figure 2: 0.96 inch TFT LCD Module (Front View).

1.3 inch TFT Module

ItemValue
Size1.3 inch
Display FormatGraphic 240RGB*240 Dot-matrix
Drive ICST7789VW
Dimensional Outline27.78(W)*39.22 (H)*3.0+/-0.1(T)mm
Resolution240RGB*240 Dots
LCD Active Area23.4 (W)*23.4 (H)mm
Dot Pitch0.0975(H) x 0.0975(V) mm
Operating Temperature-20~70°C
Front view of 1.3 inch TFT LCD module
Figure 3: 1.3 inch TFT LCD Module (Front View).

1.77 inch TFT Module

Front and back view of 1.77 inch TFT LCD module
Figure 4: 1.77 inch TFT LCD Module (Front and Back View).

1.8 inch TFT Module

Front and back view of 1.8 inch TFT LCD module
Figure 5: 1.8 inch TFT LCD Module (Front and Back View).

2.0 inch TFT Module (GMT020-01)

ItemContentsUnit
LCD Size2.0 inch(Diagonal)-
Display ModeNormally black-
Resolution240(H)RGB x 320(V)-
Dot pitch0.1275(H) x 0.1275(V) mm-
Active area30.6(H) x 40.8(V) mm-
Module size35.7(H) x 51.2(V) x2.2(D) mm-
Color arrangementRGB Vertical stripe-
Interface4 Line SPI-
Drive ICST7789VW-
Luminance(cd/m2)400 (TYP)-
Viewing DirectionAll View-
Backlight4 White LED-
Operating Temp.-20℃ ~ + 70℃℃
Storage Temp.-30℃ ~ + 80℃℃
WeightTBDg
Specifications table for 2.0 inch TFT LCD module (GMT020-01)
Figure 6: 2.0 inch TFT LCD Module (GMT020-01) Specifications.

2.4 inch TFT Module

NameParameter
Display ColorRGB 65K color
SKUhave touch screen: MSP2402
have no touch screen: MSP2401
Screen Size2.4(inch)
TypeTFT
Driver ICST7789V
Resolution320*240 (Pixel)
Module Interface4-wire SPI interface
Active Area (AA area)36.72x48.96(mm)
Module PCB Size77.18x42.72(mm)
Operating Temperature-20℃~60℃
Storage Temperature-30℃~70℃
VCC power voltage3.3V~5V
Logic IO port voltage3.3V(TTL)
Power ConsumptionTBD
Rough Weight (Package containing)No touch: 26(g) / With touch: 36(g)
Specifications table for 2.4 inch TFT LCD module
Figure 7: 2.4 inch TFT LCD Module Specifications.

3. Setup and Pin Descriptions

Proper connection of the display module to your microcontroller is crucial for its operation. All modules use a Serial Peripheral Interface (SPI).

3.1 Common Pin Descriptions

Pin No.SymbolDescription
1GNDGround connection.
2VCCPower supply input (typically 3.3V). Modules with PCB may accept 5V due to an onboard regulator.
3SCLSerial Clock pin for SPI communication.
4SDASerial Data Input/Output pin for SPI communication. Data is latched on the rising edge of SCL.
5RES (or RESET)Reset signal input. Active low. Keep high during normal operation.
6DC (or A0)Data/Command Control pin. Selects between data and command modes.
7CSChip Select pin. Active low (low enables chip, high disables).
8BLK (or LED)Backlight control pin. Connect to appropriate voltage (max 3.2V) with a current-limiting resistor if needed.

3.2 Module Specific Pinouts and Wiring

0.96 inch TFT Module Pinout

The 0.96 inch module typically has 8 pins as described in the common pin descriptions.

Back view of 0.96 inch TFT LCD module with pin labels
Figure 8: 0.96 inch TFT LCD Module Pin Labels.

1.3 inch TFT Module Pinout

The 1.3 inch module also typically uses 7 or 8 pins, similar to the common pin descriptions. Note that some variants might combine BLK with VCC or have different pin counts.

Front view of 1.3 inch TFT LCD module (Black Board)
Figure 9: 1.3 inch TFT LCD Module (Black Board).

1.8 inch TFT Module Pinout

The 1.8 inch module uses a 4-SPI interface. The pin assignments are detailed below:

NO.SymbolDescription
1GNDPower Ground
2LEDKLED Cathode
3LEDALED Anode
4VDDPower Supply for Analog
5GNDPower Ground
6GNDPower Ground
7D/CDisplay data/command selection pin in 4-line serial interface.
8CSChip selection pin; low enable, high disable.
9SCLSerial interface clock
10SDASPI interface input/output pin. The data is latched on the rising edge of the SCL signal.
11RESETReset signal. Active low. Must be applied to properly initialize the chip.
12GNDPower Ground
Pinout diagram for 1.8 inch TFT LCD module
Figure 10: 1.8 inch TFT LCD Module Pinout Diagram.

Power Supply Considerations:

  • TFT Power Supply: The screen power supply is 2.8-3.3V. Avoid using 5V directly unless the module has an integrated 3V regulator IC (which many PCB-mounted modules do).
  • Backlight Power Supply (LED pin): The maximum backlight power supply is 3.2V. If using a 3.3V power supply, a 5 ohm current-limiting resistor should be connected in series. For a 5V supply, a 25 ohm resistor in series is recommended.

2.0 inch TFT Module Pinout

The 2.0 inch module (GMT020-01) also uses a 4-line SPI interface. The pin assignments are similar to the 1.8 inch module:

NO.SymbolDescription
1GNDPower Ground
2LEDKLED Cathode
3LEDALED Anode
4VDDPower Supply for Analog
5GNDPower Ground
6GNDPower Ground
7D/CDisplay data/command selection pin in 4-line serial interface.
8CSChip selection pin; low enable, high disable.
9SCLThis pin is used to be serial interface clock
10SDASPI interface input/output pin. The data is latched on the rising edge of the SCL signal.
11RESETThis signal will reset the device and it must be applied to properly initialize the chip. Signal is active low.
12GNDPower Ground
Pin assignment table for 2.0 inch TFT LCD module
Figure 11: 2.0 inch TFT LCD Module Pin Assignment Table.
Pinout diagram for 2.0 inch TFT LCD module
Figure 12: 2.0 inch TFT LCD Module Pinout Diagram.
Alternative pinout diagram for 2.0 inch TFT LCD module
Figure 13: 2.0 inch TFT LCD Module Alternative Pinout Diagram.
Dimension diagram for 2.0 inch TFT LCD module
Figure 14: 2.0 inch TFT LCD Module Dimension Diagram.
Alternative dimension diagram for 2.0 inch TFT LCD module
Figure 15: 2.0 inch TFT LCD Module Alternative Dimension Diagram.
Schematic diagram for 2.0 inch TFT LCD module
Figure 16: 2.0 inch TFT LCD Module Schematic Diagram.
Alternative schematic diagram for 2.0 inch TFT LCD module
Figure 17: 2.0 inch TFT LCD Module Alternative Schematic Diagram.

4. Operating Instructions

These TFT LCD modules communicate via a Serial Peripheral Interface (SPI). To operate the display, you will need a microcontroller (e.g., Arduino, ESP32) and appropriate libraries (e.g., Adafruit GFX, Adafruit ST7735/ST7789 library).

4.1 Basic SPI Communication

The SPI interface typically requires four main lines:

  • SCL (Serial Clock): Provides the clock signal for data transfer.
  • SDA (Serial Data): Carries the data to be sent to the display.
  • CS (Chip Select): Activates the display module for communication.
  • DC (Data/Command): Differentiates between data and command bytes being sent.

Additionally, a RESET pin is used for initializing the display, and a BLK (Backlight) pin controls the backlight.

4.2 Example IO Connection (1.8 inch module)

For the 1.8 inch module, a typical IO connection method might look like this in a microcontroller program (e.g., C-like syntax):

/*
Program default IO connection method:
sbit LCD_CS =P0^0; //chip select
sbit LCD_AO =P0^2; //data/command switch
sbit LCD_SDA =P1^5; // Data
sbit LCD_SCK =P1^7; //clock
sbit LCD_REST =P0^1; //reset
*/

Refer to the specific library documentation for your chosen microcontroller platform for detailed wiring and code examples.

5. Maintenance

  • Cleaning: Use a soft, dry, lint-free cloth to gently wipe the display surface. Avoid using harsh chemicals or abrasive materials.
  • Handling: Handle the module by its edges to avoid touching the display area or damaging the flexible flat cable (FPC).
  • Storage: Store the module in a dry, anti-static environment within the specified storage temperature range (-30℃ to +80℃).
  • Power: Always ensure correct voltage and current limiting for the backlight to prevent damage.

6. Troubleshooting

  • Display is blank:
    • Check power connections (VCC and GND) and ensure correct voltage (3.3V).
    • Verify backlight connection (BLK/LED) and ensure it receives power with appropriate current limiting.
    • Confirm the RESET pin is properly toggled (active low pulse) during initialization and held high during operation.
    • Check SPI connections (SCL, SDA, CS, DC) for continuity and correct wiring.
    • Ensure your microcontroller code is correctly initializing the display driver IC (ST7735S or ST7789VW) and sending display commands.
  • Incorrect colors or distorted image:
    • Verify that the correct display driver IC (ST7735S/ST7789VW) is selected in your software library.
    • Check the resolution settings in your code to match the specific module (e.g., 80x160, 240x240, 320x240).
    • Ensure data is being sent correctly over SPI (check clock polarity and phase).
  • Display not responding to commands:
    • Confirm the CS (Chip Select) pin is active low during communication.
    • Check the DC (Data/Command) pin is correctly switching between command and data modes.
    • Ensure the SPI clock speed is compatible with the display module and microcontroller.
  • Touch screen not working (for 2.4 inch touch variant):
    • Verify touch screen specific connections (if applicable, beyond standard SPI).
    • Ensure the correct touch controller library is being used and initialized.

7. User Tips

  • Full Color Display: These modules are designed for full-color graphical output, displaying 65K colors. They are ideal for displaying sensor data, custom interfaces, or small images.
  • Multimedia Playback: These displays are primarily for static or animated graphical interfaces. They are generally not designed for direct playback of video clips or streaming content from a phone without significant external processing and buffering by the microcontroller.
  • Libraries: For ease of use, consider utilizing established libraries like Adafruit GFX and the specific display driver libraries (e.g., Adafruit ST7735, Adafruit ST7789) with your microcontroller platform. These libraries abstract much of the low-level SPI communication.

8. Warranty and Support

For technical support, driver code, or further assistance, please refer to the official product page or contact the seller directly. Information regarding specific warranty periods may be available from your point of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.