E-bike EN06 LCD Display

Contents

Electric Bike EN06 LCD Display Meter User Manual

Model: EN06 LCD Display

1. Product Overview

The EN06 LCD Display Meter is designed for electric bikes, mountain bikes, and scooters, providing essential riding data and control. It features a clear display for battery power, speed, and other metrics, ensuring a comprehensive overview of your ride.

Front view of the EN06 LCD Display Meter with cable

Figure 1: EN06 LCD Display Meter (Front View)

Key Features:

  • Multiple Data Display: Real-time battery power, power consumption, speed, and riding mileage.
  • Wide Voltage Compatibility: Supports 24V, 36V, and 48V systems.
  • Universal Handlebar Fit: Designed for 22.2mm diameter handlebars.
  • Durable Construction: Plastic casing offers good toughness and waterproof performance, protecting internal circuits.
  • Easy Installation: Simple to install and replace.

2. Safety Information

Please read all safety instructions before installation and use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Ensure all connections are secure and correctly matched to prevent electrical shorts or malfunctions.
  • Do not attempt to open or modify the display unit, as this may void the warranty and cause damage.
  • Keep the display away from extreme temperatures, direct sunlight for prolonged periods, and corrosive substances.
  • Ensure proper installation and handling of electronic components to prevent potential risks.

3. Installation Guide

Follow these steps to properly install your EN06 LCD Display Meter:

3.1 Handlebar Mounting

  1. Identify a suitable position on your handlebar (left side is typical) with a diameter of 22.2mm.
  2. Loosen the clamp screw on the back of the display unit.
  3. Position the display on the handlebar and tighten the screw securely, ensuring the display is stable and visible.
Bottom view of EN06 LCD Display showing handlebar clamp

Figure 2: Handlebar Clamp Detail

3.2 Electrical Connection

The EN06 display comes with either a waterproof plug or an SM plug. Ensure your e-bike controller has a compatible connector and uses the No. 2 communication protocol.

  1. Locate the corresponding connector on your e-bike's wiring harness.
  2. Carefully align the pins and push the display's connector firmly into the controller's connector until it clicks into place (for waterproof connectors) or is fully seated (for SM connectors).
  3. Ensure the connection is secure and free from strain.
EN06 LCD Display with waterproof connectorEN06 LCD Display with SM connector

Figure 3: Waterproof (Left) and SM (Right) Connectors

Important: This display requires a controller that uses the No. 2 communication protocol. Incompatibility may lead to error codes or non-functionality.

4. Operating Instructions

The EN06 display provides intuitive control over your e-bike's functions.

Angled view of EN06 LCD Display showing buttons

Figure 4: EN06 LCD Display with Control Buttons

4.1 Button Functions

  • Power Button (Power button icon):
    • Press and hold to turn the display ON/OFF.
    • Short press (when ON) to cycle through display modes (e.g., Odometer, Trip Distance, Max Speed).
  • Plus Button (+):
    • Short press to increase the pedal assist level (PAS).
    • Long press for specific functions (e.g., walk assist, depending on controller).
  • Minus Button (-):
    • Short press to decrease the pedal assist level (PAS).
    • Long press for specific functions (e.g., headlight control, depending on controller).

4.2 Displayed Information

The LCD screen provides the following information:

  • Current Speed
  • Battery Level Indicator
  • Pedal Assist System (PAS) Level
  • Odometer / Trip Distance
  • Error Codes (if any)

5. Maintenance

Proper maintenance ensures the longevity and optimal performance of your EN06 LCD Display Meter.

  • Cleaning: Wipe the display screen and casing with a soft, damp cloth. Avoid using abrasive cleaners, solvents, or harsh chemicals that could damage the plastic or screen.
  • Water Resistance: The display is designed to be waterproof, but avoid submerging it in water or exposing it to high-pressure water jets.
  • Storage: When not in use for extended periods, store the e-bike and display in a dry, cool place, away from direct sunlight.
  • Cable Inspection: Periodically check the connecting cables for any signs of wear, cuts, or damage. Ensure connectors are clean and free of debris.

6. Troubleshooting

This section addresses common issues you might encounter with your EN06 LCD Display Meter.

ProblemPossible CauseSolution
Display does not turn on.
  • Low or dead e-bike battery.
  • Loose or disconnected power cable.
  • Faulty display or controller.
  • Check e-bike battery charge.
  • Verify all electrical connections are secure.
  • Contact support if issue persists.
Error Code E-06 displayed.
  • Communication protocol mismatch between display and controller.
  • Loose communication cable.
  • Ensure your controller uses the No. 2 communication protocol.
  • Check the communication cable connection.
  • Power cycle the e-bike (turn off, wait 10 seconds, turn on).
Incorrect speed or distance readings.
  • Improper wheel size setting (if configurable).
  • Faulty speed sensor.
  • Consult your e-bike's main manual for display settings.
  • Check speed sensor connection and functionality.

7. Specifications

FeatureDetail
ModelEN06 LCD Display
TypeDisplay
MaterialPVC, Copper, ABS
Voltage Compatibility24V, 36V, 48V
Handlebar Diameter22.2mm / 0.87 inch
Connector TypeWaterproof plug or SM plug (variant dependent)
Communication ProtocolNo. 2
WeightApprox. 73g / 2.6oz
Dimensions (L x H)62mm x 46mm (2.44 inch x 1.81 inch)
Button Area Width40mm / 1.57 inch
Diagram showing dimensions of the EN06 LCD Display

Figure 5: EN06 LCD Display Dimensions

8. User Tips

  • Compatibility Check: Before purchasing or installing, always confirm that your e-bike's controller uses the No. 2 communication protocol to avoid compatibility issues, especially if you encounter error codes like E-06.
  • Secure Mounting: Ensure the display is firmly mounted on the handlebar to prevent movement or damage during rides, particularly over rough terrain.
  • Cable Management: Route cables neatly and securely to prevent them from snagging or getting damaged, which can lead to intermittent connection issues.

9. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

The product is generally covered by a return policy (e.g., free returns within 90 days as per platform policy). Specific warranty terms may vary by seller.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.