1. Introduction
The JIKONG JK-B2A25SRP Battery Management System (BMS) is an intelligent protection board designed for large-capacity series lithium battery packs. It provides comprehensive battery protection, voltage acquisition, and active voltage equalization. This system is compatible with various battery chemistries including Li-ion, LiFePO4, and LTO, supporting configurations from 3S to 25S.
Key features include continuous active balancing up to 2A, real-time monitoring via Bluetooth APP, and support for external communication interfaces like RS485, CAN, and LCD displays. The BMS is suitable for a wide range of applications, from small electric vehicles to high-power energy storage systems.


2. Specifications
The JK-B2A25SRP BMS offers robust performance and protection features. Below are the main technical indicators and general specifications:
2.1 General Specifications
- Battery Series Support: 3S to 25S (Li-ion, LiFePO4, LTO)
- Active Balancing Current: 2A (continuous)
- Voltage Acquisition Range: 1V ~ 5V
- Voltage Acquisition Accuracy: ±3mV
- Operating Temperature: -20℃ to 70℃
- Power Requirements: 16V ~ 100V (can use battery self-powered or external power supply)
- Maximum Power Consumption: 1.5W (excluding relay power consumption)
- Shutdown Power Consumption: 20mW
- Dimensions: 188.6mm (length) x 94mm (width) x 23.5mm (thickness)
- Communication Interfaces: RS485, CAN bus, GPS interface, Bluetooth (mobile APP), LCD interface (optional)
- Relay Driving Voltage: 12V, 24V, external (maximum 84V), standard 12V
- Current Shunt: 500A (75mv) equipped
- Temperature Probes: Support 3 temperature probes
- Coulomb Counter: Included
- ACC Ignition Switch: Supported
- Weak Current Switch: Supported (display interface activated)
- Heating Function: Supported
2.2 Protection Parameters (Configurable via APP)
- Cell Undervoltage Protection: LiFePO4: 2.500V; Li-ion: 2.800V
- Cell Undervoltage Recovery: LiFePO4: 2.650V; Li-ion: 3.200V
- Cell Overcharge Voltage: LiFePO4: 3.65V; Li-ion: 4.2V
- Cell Overcharge Recovery: LiFePO4: 3.6V; Li-ion: 4.1V
- Trigger Equalization Dropout: 0.01V
- Automatic Shutdown Voltage: LiFePO4: 2.5V; Li-ion: 2.799V
- Charging Overcurrent Protection: 100A (delay: 30s, release: 60s)
- Discharge Overcurrent Protection: 400A (or other current depending on relay, delay: 30s, release: 60s)
- Short Circuit Protection Release Time: 60s
- Charging Over Temperature Protection: 70℃ (recovery: 60℃)
- Discharge Over Temperature Protection: 70℃ (recovery: 60℃)
- Charging Low Temperature Protection: -20℃ (recovery: -10℃)
- MOS Over Temperature Protection: 100℃ (recovery: 80℃)


3. Setup and Wiring
Proper installation and wiring are critical for the safe and efficient operation of the BMS. Ensure all connections are secure and correct before powering on the system.
3.1 General Wiring Principles
- Connect the battery cells to the BMS in the correct series order (B0, B1, B2... up to B25).
- Connect the charge and discharge contactors, precharge resistor, and shunt as shown in the diagrams.
- Ensure temperature sensors are correctly placed on the battery cells.
- Connect the charger and load to the appropriate terminals.
- Optional modules like RS485, CAN, or LCD displays should be connected to their designated ports.
Note: Relays (e.g., 100A, 350A, 500A) are not included with the BMS and must be purchased separately based on your current requirements.

3.2 Wiring Diagrams
Refer to the following diagrams for specific cell configurations:



3.3 Connecting Optional Modules
The BMS supports various optional modules for enhanced functionality:
- RS485 Module: Connect the RS485 module to the designated port on the BMS for external communication. This module needs to be purchased separately.
- LCD Display: Connect the LCD display (e.g., 4.3-inch or 2.5-inch) to the display port. Ensure the 12V input power supply, BMS power-on signal, and GND connections are correct. LCD displays are sold separately.



4. Operation
The JIKONG BMS is designed for ease of use, with active balancing and mobile APP control as primary operational features.
4.1 Active Balancing
The BMS utilizes super capacitors for active energy transfer balancing. This means energy is transferred between cells to equalize their voltage, improving battery efficiency and prolonging battery life. The balancing current is a continuous 2A and operates independently of the cell voltage difference.

4.2 Mobile APP Control
The BMS features a Bluetooth communication function, allowing connection to a mobile APP (available for Android and iOS). Through the APP, users can:
- Check the real-time voltage of individual battery cells.
- Monitor the active balancing status.
- Modify various setting parameters for protection functions (e.g., overcharge/discharge voltage, current limits).
- Control charge and discharge switches.

5. Maintenance
To ensure the longevity and optimal performance of your JIKONG BMS, follow these maintenance guidelines:
- Regularly check all wiring connections for tightness and corrosion.
- Keep the BMS unit clean and free from dust and moisture.
- Monitor battery cell health and balancing status via the mobile APP.
- Ensure the BMS operates within its specified temperature range (-20℃ to 70℃).
- If any issues arise, consult the troubleshooting section or contact support.
6. Troubleshooting
This section provides guidance on common issues you might encounter with your JIKONG BMS.
| Problem | Possible Cause | Solution |
|---|---|---|
| BMS not powering on | Incorrect wiring, insufficient power supply, or faulty unit. | Verify all power connections (16V-100V). Check for correct polarity. Ensure the battery pack voltage is within the operational range. |
| Cells not balancing | Voltage difference below trigger threshold, faulty cell, or balancing circuit issue. | Check APP for balancing status and trigger settings. Ensure cell voltages are within the range where balancing is active. Inspect cell connections. |
| Overcurrent protection tripping | Load current exceeds set limit, short circuit, or faulty relay. | Reduce load. Check for short circuits in the system. Verify relay rating and functionality. Adjust overcurrent parameters in the APP if necessary. |
| APP not connecting via Bluetooth | Bluetooth off, incorrect APP version, or interference. | Ensure Bluetooth is enabled on your mobile device. Download the latest APP version. Try connecting in close proximity to the BMS. |
| Inaccurate voltage readings | Poor cell connections, faulty wiring, or sensor issue. | Inspect all cell voltage sensing wires for secure connections. Ensure wires are not damaged. |
7. User Tips
- Essential Accessories: Remember that the LCD display, RS485 module, and relays are typically sold separately. Plan your purchase to include these if needed for your setup.
- Activation: An external display or RS485 module might be necessary to activate certain BMS functions or to initially configure the system.
- Installation Environment: When installing the BMS, consider mounting it in a protective enclosure or cabinet to shield it from environmental factors and physical damage.
- Firmware Updates: Periodically check for firmware updates for the BMS and the mobile APP to ensure optimal performance and access to new features.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the manufacturer or your authorized dealer. Keep your purchase receipt and product serial number handy for any support requests.
You can find additional resources and contact information on the official JIKONG BMS website: www.jk-bms.com