1. Product Overview
The Recordio DT+ Series Power Digital Built-in Amplifier is a Class D subwoofer board designed for professional audio applications. It features a new generation Class TD module for stable control of high-power output and strong load capacity, delivering vivid sound with strong bass, smooth mid-frequencies, and powerful treble.


2. Safety Information
Please read and understand all safety instructions before operating the amplifier module. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- Ensure proper grounding for all connections.
- Do not expose the unit to rain or moisture.
- Do not open the casing; refer servicing to qualified personnel.
- Ensure adequate ventilation to prevent overheating.
- Use only specified power cables and connectors.

The amplifier module is equipped with smart protection features for stable performance, including:
- Short Circuit Protection
- Overload Protection
- Voltage Limit Protection
- Temperature Detection
3. Setup and Installation
3.1 Unpacking
Carefully unpack the amplifier module and inspect it for any signs of damage. Retain the packaging for future transport or storage.

3.2 Mounting the Module
The amplifier module is designed for built-in installation into a speaker cabinet. Ensure the speaker cabinet has the appropriate cutout and mounting points for secure installation.

3.3 Connections
Refer to the diagram below for proper connection of audio input, power, and linking multiple units.

- Audio Input: Connect your audio source (e.g., mixer, pre-amplifier) to the 'INPUT' XLR connector.
- Link-Out: Use the 'LINK-OUT' XLR connector to daisy-chain the audio signal to another amplifier module or active speaker.
- Power Input: Connect the main power cable to the 'AC INPUT' connector.
- Power Connection (AC Link): Use the 'AC LINK' output to provide power to another amplifier module, if supported and within power limits.
- Speaker Output: Connect your passive speaker to the speaker output connector.
Video Demonstration:
4. Operating Instructions
4.1 Powering On/Off
Press the 'POWER PUSH ON' button to turn the unit on or off. The 'POWER' indicator will illuminate when the unit is on.
4.2 Controls
- LEVEL: Adjusts the overall output volume of the amplifier.
- FAD: (Functionality may vary by model) Typically controls a specific frequency band or effect.
- SUB: Adjusts the subwoofer level or crossover frequency.
- PHASE: Adjusts the phase of the output signal (0° or 180°) to optimize bass response with other speakers.
4.3 Indicators
- POWER: Indicates the unit is powered on.
- SIG (Signal): Illuminates when an audio signal is detected.
- CLIP: Illuminates when the input signal is too high, causing clipping. Reduce the input level to prevent distortion.
- PRO (Protect): Illuminates when a protection circuit is activated (e.g., overheating, short circuit). The unit will temporarily shut down to prevent damage.
4.4 Application Scenarios
The DT+ series amplifier modules are suitable for a wide range of professional audio environments.

5. Maintenance
5.1 Cleaning
Regularly clean the exterior of the amplifier module with a soft, dry cloth. Do not use liquid cleaners or solvents, as they may damage the finish or internal components.
5.2 Cooling System
The amplifier features a powerful cooling system to maintain optimal operating temperature. Ensure that the fan vents are clear of obstructions to allow for proper airflow. Periodically check for dust accumulation and gently clean the vents if necessary.

6. Troubleshooting
If you encounter issues with your amplifier module, refer to the following common problems and solutions:
- No Power: Check the power cable connection and ensure the power switch is in the 'ON' position. Verify the power source is active.
- No Sound: Check all audio input and output connections. Ensure the 'LEVEL' control is not set to minimum. Verify the audio source is functioning correctly.
- Distorted Sound (CLIP indicator on): The input signal is too strong. Reduce the output level from your audio source until the 'CLIP' indicator no longer illuminates.
- Unit Shuts Down (PRO indicator on): This indicates a protection circuit has been activated.
- Overheating: Ensure adequate ventilation around the module. Clear any obstructions from the cooling fan. Allow the unit to cool down before restarting.
- Short Circuit: Disconnect all speaker outputs and power cycle the unit. If it powers on normally, check your speaker cables and speakers for short circuits.
- Voltage Limit: Ensure the power supply voltage is within the specified range.
7. Specifications
The following table details the product parameters for the DT+ Series amplifier modules:

| Feature | 500DT | 700DT | 900DT | 1500DT |
|---|---|---|---|---|
| Output Power (8Ω) | 1×300W | 1×500W | 1×600W | 1×1000W |
| Output Power (4Ω) | 1×500W | 1×700W | 1×900W | 1×1500W |
| Frequency Response | 20Hz - 20KHz +/- 0.5dB | |||
| 4Ω - 8Ω / STEREO | 0.2% | |||
| 20Hz - 20KHz 8Ω/BRIDGE | - | |||
| S/N Rate | ≥90dB | |||
| R L=8Ω 1KHz | <700 | |||
| Input Sensitivity | 1.0V | |||
| Input Impedance | 20KΩ/10KΩ (Bal/Unbal) | |||
| Cooling | Air flow from front to rear | |||
| Protect | POWER ON/OFF, Mute, DC, short circuit protection, temperature detection, overheating protection | |||
| Dimensions (mm) | 333×134×80 | 377×137×80 | ||
| Net Weight (KG) | 3.7KG | 3.7KG | 4.2KG | 4.3KG |
7.1 Physical Dimensions
Refer to the diagrams below for the physical dimensions of each module variant.




8. User Tips
- Output Power Selection: The DT+ series offers various output power options (500W, 700W, 900W, 1500W). Choose the model that best matches the power requirements of your speakers to ensure optimal performance and prevent damage.
- Professional Use: This is a professional amplifier module. Familiarity with audio equipment and proper installation techniques is recommended for best results.
- Single Unit Operation: Each amplifier module operates as a single unit. If you require more power or channels, consider using multiple modules or a multi-channel amplifier.
9. Warranty and Support
9.1 Warranty
This product comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, unauthorized modifications, or improper installation.
9.2 Technical Support
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Recordio Official Store customer support. Provide your product model and purchase details for efficient service.