Cherub GT2/3/4/6, GU3/GS3

Contents

Cherub G-Tone Series Acoustic Guitar Preamp User Manual

Models: GT-2, GT-3, GT-4, GT-6, GU3, GS3

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Cherub G-Tone Series Acoustic Guitar Preamp. Please read this manual thoroughly before use to ensure proper function and longevity of your device.

The Cherub G-Tone series includes various models such as GT-2, GT-3, GT-4, GT-6, GU3, and GS3, each offering unique features tailored for acoustic guitar amplification and tone shaping.

2. Package Contents

Upon opening your package, please verify that all components are present:

  • Cherub G-Tone Equalizer/Preamp Unit (specific model: GT-2, GT-3, GT-4, GT-6, GU3, or GS3)
  • Endpin Jack with Battery Compartment
  • Piezo Pickup Strip
  • Mounting Screws
  • Owner's Manual (this document)
Cherub G-Tone Series Preamp kit components including preamp, endpin jack, piezo pickup, screws, and manual.
Figure 1: Typical Cherub G-Tone Preamp Kit Components

3. Specifications

FeatureDescription
MaterialABS Plastic
Equalizer3-Band (Low, Middle, High)
Power Supply9V 6F22 Battery (not included)
TunerIntegrated LED Tuner (mutes output when active)
Phase FunctionYes
Low Battery IndicatorYes
Additional Controls (GT-3)Brilliance, Notch
Additional Controls (GT-4)Mid Freq, Notch
Additional Controls (GT-6)Reverb/Delay, Chorus/Wide
Dimensions (GT-2 Preamp)Approx. 53.5mm x 49mm
Dimensions (GT-3/GT-4 Preamp)Approx. 53.5mm x 55mm
Dimensions of Cherub GT-2 preamp, showing approximate measurements of 53.5mm by 49mm.
Figure 2: GT-2 Preamp Dimensions
Dimensions of Cherub GT-3/GT-4 preamp, showing approximate measurements of 53.5mm by 55mm.
Figure 3: GT-3/GT-4 Preamp Dimensions

4. Setup and Installation

The Cherub G-Tone preamp system is designed for installation into acoustic guitars. Due to the nature of the installation, which may involve modifying your instrument, professional installation by a qualified luthier or guitar technician is highly recommended.

4.1. Battery Installation

  1. Locate the battery compartment, typically integrated with the endpin jack.
  2. Open the battery compartment.
  3. Insert one 9V 6F22 battery, ensuring correct polarity (+/-).
  4. Close the battery compartment securely.

Note: The 9V 6F22 battery is not included and must be purchased separately.

4.2. System Components Overview

Diagram showing the Cherub G-Tone preamp unit and the separate endpin jack with battery compartment.
Figure 4: Preamp and Endpin Jack Components

The system consists of the main preamp unit (which houses the controls and tuner) and a separate endpin jack assembly that also serves as the battery holder. These components are connected internally within the guitar body.

5. Operating Instructions

Familiarize yourself with the controls on your specific Cherub G-Tone preamp model. While GU3 and GS3 models are part of the series, detailed control descriptions below focus on the GT series due to available information. Please refer to your specific unit's layout if it differs.

5.1. General Controls (Applicable to GT-2, GT-3, GT-4, GT-6)

  • VOL. (Volume) Knob: Adjusts the overall output volume of the preamp.
  • LOW Knob: Controls the bass frequencies. Rotate to increase or decrease low-end response.
  • MIDDLE Knob: Controls the mid-range frequencies. Rotate to increase or decrease mid-range response.
  • HIGH Knob: Controls the treble frequencies. Rotate to increase or decrease high-end response.
  • PHASE Button: Engages or disengages the phase function. This can help reduce feedback in certain live sound situations.
  • TUNER Button: Activates the built-in LED tuner. When the tuner is active, the audio output will be muted. Press again to deactivate the tuner and restore audio output.
  • BATT. Indicator: An LED that illuminates to indicate a low battery condition.

5.2. Model-Specific Controls

5.2.1. Cherub GT-2

Close-up of Cherub GT-2 preamp control panel with Volume, Low, Middle, High, Phase, and Tuner controls.
Figure 5: GT-2 Control Panel

The GT-2 features the general controls listed above for basic 3-band EQ, volume, phase, and tuner functions.

5.2.2. Cherub GT-3

Close-up of Cherub GT-3 preamp control panel with Volume, Low, Middle, High, Phase, Brilliance, Notch, and Tuner controls.
Figure 6: GT-3 Control Panel

In addition to the general controls, the GT-3 includes:

  • BRILLIANCE Knob: Adjusts the presence or sparkle of the sound.
  • NOTCH Knob: Helps to eliminate feedback by cutting a specific frequency.

5.2.3. Cherub GT-4

Close-up of Cherub GT-4 preamp control panel with Volume, Low, Middle, High, Phase, Mid Freq, Notch, and Tuner controls.
Figure 7: GT-4 Control Panel

The GT-4 model adds advanced mid-range and feedback control:

  • Mid Freq Knob: Adjusts the specific frequency point that the MIDDLE knob affects.
  • NOTCH Knob: Used to adjust feedback suppression.

5.2.4. Cherub GT-6

Close-up of Cherub GT-6 preamp control panel with Volume, Low, Middle, High, Phase, Reverb/Delay, Chorus/Wide, and Tuner controls.
Figure 8: GT-6 Control Panel

The GT-6 model incorporates built-in effects:

  • REVERB/DELAY Knob: Adjusts the level of reverb and delay effects.
  • CHORUS/WIDE Knob: Adjusts the level of chorus and widening effects.

6. Maintenance

6.1. Battery Replacement

When the BATT. indicator illuminates, it's time to replace the 9V battery. Follow the battery installation steps in Section 4.1.

6.2. Cleaning

Wipe the preamp unit with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the ABS plastic material and electronic components.

7. Troubleshooting

  • No Sound Output:
    • Check if the tuner is active. The output is muted when the tuner is on.
    • Verify the 9V battery is correctly installed and not depleted (check BATT. indicator).
    • Ensure all cables (guitar to amp/PA) are securely connected.
    • Check the volume knob on the preamp and your amplifier.
  • Weak or Distorted Sound:
    • Replace the 9V battery if the BATT. indicator is on or if the sound is weak.
    • Adjust the EQ (LOW, MIDDLE, HIGH) settings.
    • Ensure the piezo pickup is correctly seated under the saddle.
  • Feedback Issues:
    • Engage the PHASE button.
    • For GT-3 and GT-4 models, adjust the NOTCH control to target and eliminate problematic frequencies.
    • Reduce the overall volume.
    • Move further away from the amplifier or monitor.

8. User Tips

  • Experiment with the EQ settings (LOW, MIDDLE, HIGH) to find the best tone for your guitar and playing environment. Small adjustments can make a big difference.
  • Always carry a spare 9V battery, especially for live performances, to avoid unexpected power loss.
  • The PHASE button is a powerful tool for feedback suppression; don't hesitate to use it when feedback occurs.

9. Warranty and Support

For any issues with defective or faulty products, please contact the seller or manufacturer directly. It is recommended to provide photos or videos of the issue to facilitate a quicker resolution, such as a replacement or refund.

Please retain your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.