LILYGO T-Beam V1.1 LoRa ESP32 With OLED

Contents

LILYGO TTGO T-Beam V1.1 LoRa ESP32 Development Module User Manual

Model: T-Beam V1.1 LoRa ESP32 With OLED

Brand: LILYGO

1. Introduction

The LILYGO TTGO T-Beam V1.1 is a versatile development module integrating an ESP32 microcontroller, LoRa long-range wireless communication, a NEO-6M GPS module, and an OLED display. It supports various LoRa frequencies (433/868/915/923Mhz) and features a built-in 18650 battery holder for portable applications. This manual provides essential information for setting up, operating, and maintaining your T-Beam V1.1 module.

2. Features

  • Microcontroller: ESP32 (4MB Flash)
  • Wireless Connectivity: Wi-Fi, Bluetooth 4.2, LoRa (SX1278/SX1276/SX1262 options)
  • LoRa Frequencies: 433MHz, 868MHz, 915MHz, 923MHz (version dependent)
  • GPS Module: NEO-6M (supports GPS protocol, onboard RTC crystal, interrupt/wakeup)
  • Power Management Unit (PMU): AXP192
  • Display: 0.96 inch 128x64 OLED (SSD1306)
  • Onboard Functions: 3 Buttons (Power, IO38, Reset)
  • Power Supply: USB or 18650 battery holder
  • Serial Chip: CH9102
  • LoRa Transceiver: High sensitivity (-148 dBm), 300 kbps transceive rate

3. Specifications

T-Beam V1.1 + OLED SSD1306 Specifications
ComponentDetail
MCUESP32
Flash4MB
Serial ChipCH9102
Wireless ProtocolWi-Fi + Bluetooth 4.2
PMUAXP192
Onboard Functions3 Buttons (Power+IO38+Reset)
Power Supply ModeUSB / 18650 battery
GPS ModuleNEO-6M (Supports GPS protocol, Onboard RTC crystal, Support interrupt/wakeup)
LoRa TransceiverHigh sensitivity: -148 dBm, Transceive rate: 300 kbps
Optional LoRa VersionSX1278 / SX1276 / SX1262 (frequency dependent)
Dimensions (approx.)100.13mm (Length) x 32.89mm (Width)
Detailed specifications and features of the T-Beam V1.1 + OLED SSD1306 module.
Figure 3.1: Detailed Specifications and Features
Comparison table for LoRa T-BEAM V1.1 different LoRa chips (SX1278, SX1276, SX1268, SX1262) and their characteristics.
Figure 3.2: LoRa Chip Comparison for T-Beam V1.1
Comparison table for various T-Beam V1.1 configurations including OLED, Meshtastic, M8N GNSS, and LoRa SX1262 options.
Figure 3.3: T-Beam V1.1 Configuration Comparison
Mechanical dimensions diagram of the T-Beam V1.1 board.
Figure 3.4: Mechanical Dimensions of T-Beam V1.1

4. Components Overview

The T-Beam V1.1 module is a compact board featuring several key components:

  • Main Board: Integrates ESP32, LoRa module, GPS module, PMU, and various GPIO pins.
  • OLED Display: A 0.96 inch 128x64 pixel OLED screen for displaying information. Note: The OLED is not pre-soldered to the T-Beam module and requires soldering.
  • LoRa Antenna: Connects to the SMA connector for LoRa communication.
  • Pin Headers: For connecting external components and accessing GPIOs.
  • 18650 Battery Holder: Located on the back of the board for portable power.
Front view of the T-Beam V1.1 module with antenna and OLED connected.
Figure 4.1: T-Beam V1.1 Front View
Angled view of the T-Beam V1.1 module with antenna and OLED.
Figure 4.2: T-Beam V1.1 Angled View
Back view of the T-Beam V1.1 module showing the 18650 battery holder.
Figure 4.3: T-Beam V1.1 Back View with Battery Holder
Angled view of the T-Beam V1.1 module without antenna, highlighting the OLED connection area.
Figure 4.4: T-Beam V1.1 Angled View (without antenna)
Exploded view of the T-Beam V1.1 module, showing the main board, OLED, antenna, and pin headers as separate components.
Figure 4.5: T-Beam V1.1 Exploded View
Close-up image of the 0.96 inch OLED display module.
Figure 4.6: 0.96 inch OLED Display Module
Image showing the contents of the packing list for different frequency versions of the T-Beam module, including the main board, antenna, OLED, and pin headers.
Figure 4.7: Typical Packing List Contents

5. Setup Instructions

  1. Solder OLED Display: The 0.96 inch OLED display is typically not pre-soldered. Carefully solder the OLED module to the designated pins on the T-Beam board (VCC, GND, SCL, SDA). Refer to the pinout diagram for exact locations.
  2. Attach LoRa Antenna: Screw the provided LoRa antenna onto the SMA connector on the T-Beam board. Ensure it is securely fastened but do not overtighten.
  3. Insert 18650 Battery: If using battery power, insert a fully charged 18650 battery into the battery holder on the back of the board. Pay close attention to the polarity markings (+ and -) to avoid damage.
  4. Connect via USB: For initial programming and power, connect the T-Beam module to your computer using a micro-USB cable.
  5. Install Drivers: Your computer may require drivers for the CH9102 serial chip. These are usually available from the manufacturer's website or common ESP32 development resources.
  6. Firmware Flashing: The T-Beam module requires firmware to function. You can find various open-source firmware projects (e.g., SoftRF, Meshtastic) on GitHub. Follow the instructions provided by the firmware developers for flashing.
Pinout diagram for ESP32 TTGO T-Beam V1.1, showing GPIO assignments, power introduction, LED indicators (Charging, GPS Working), and 18650 battery connection.
Figure 5.1: T-Beam V1.1 Pinout and Power Introduction

6. Operating Instructions

  1. Power On/Off: Press the 'Power' button (usually labeled 'PWR' or similar) to turn the module on. Hold it down for a few seconds to turn it off.
  2. LED Indicators:
    • LED1: Charging Indicator (typically red when charging, off when charged).
    • LED2: GPS Working Indicator (blinks when searching for satellites, solid when GPS fix is acquired).
  3. OLED Display: Once firmware is loaded, the OLED display will show information as programmed (e.g., GPS coordinates, LoRa messages, battery status).
  4. Buttons: The onboard buttons (Power, IO38, Reset) can be programmed to perform various functions depending on the loaded firmware.
  5. LoRa Communication: Ensure the LoRa antenna is connected. The module will transmit and receive data according to the loaded LoRa firmware.
  6. GPS Functionality: For optimal GPS performance, ensure the module has a clear view of the sky. The GPS module will acquire satellite signals and provide location data.

7. Maintenance

  • Battery Care: If using an 18650 battery, use high-quality cells and ensure proper charging practices. Avoid over-discharging or over-charging.
  • Environmental Protection: Keep the module in a dry, dust-free environment. Avoid exposure to extreme temperatures or direct sunlight.
  • Antenna Handling: Handle the LoRa antenna carefully. Bending or damaging it can affect signal performance.
  • Firmware Updates: Regularly check for firmware updates from your chosen firmware project to benefit from new features and bug fixes.
  • Cleaning: Use a soft, dry cloth to clean the board. Avoid using liquids or abrasive materials.

8. Troubleshooting

  • Module Not Powering On: Check battery charge and polarity. Ensure USB cable is properly connected if using USB power.
  • OLED Not Displaying: Verify that the OLED is correctly soldered and that the firmware supports OLED output.
  • No LoRa Communication: Ensure the LoRa antenna is securely attached. Check LoRa frequency settings in your firmware match your region and other devices.
  • No GPS Fix: Ensure the module has a clear view of the sky. It may take several minutes to acquire a fix, especially on first use or after a long period of inactivity.
  • Connection Issues (USB/Serial): Reinstall CH9102 drivers. Try a different USB port or cable.
  • General Instability: Ensure your firmware is up-to-date and correctly configured. Consult the specific firmware project's documentation for common issues.

9. User Tips

  • OLED Soldering: As the OLED is not pre-soldered, ensure you have basic soldering skills or seek assistance from someone experienced. Proper soldering is crucial for display functionality.
  • Firmware Selection: The T-Beam is highly customizable. Explore different firmware options like SoftRF or Meshtastic based on your project requirements (e.g., APRS, mesh networking).
  • Power Consumption: LoRa and GPS can consume significant power. Optimize your firmware for low-power modes if battery life is critical.
  • Antenna Matching: Use an antenna that is tuned for your specific LoRa frequency (e.g., 433MHz, 868MHz, 915MHz) for optimal range and performance.

10. Warranty and Support

For technical support, firmware resources, and community discussions, please refer to the official LILYGO GitHub repositories and related open-source projects:

For general inquiries or issues with the product as received, please contact the seller directly. The seller's store is HiTech Wireless Module And Accessories Store.

Video 10.1: Seller's Company Overview and Contact Information

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.