Leclstar LED Garage Light

LED Garage Light User Manual

Model: LED Garage Light | Brand: Leclstar

Introduction

Thank you for choosing the Leclstar LED Garage Light. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new lighting fixture. Please read this manual thoroughly before installation and keep it for future reference.

Safety Information

  • Always turn off the power supply before installing, removing, or performing any maintenance on the light fixture.
  • Ensure the voltage supply (AC85-265V) matches the requirements of the light fixture.
  • Do not touch the light panels immediately after prolonged use, as they may be hot due to heat dissipation.
  • This product is designed for indoor use in dry environments. Avoid exposure to water or high humidity.
  • Do not attempt to disassemble or modify the light fixture, as this will void the warranty and may cause electrical hazards.
  • Keep out of reach of children.

Package Contents

Please check the package to ensure all components are present and undamaged:

  • LED Garage Light (Quantity and panel configuration may vary based on purchased model, e.g., 3-panel, 5-panel, 6-panel, 10-panel, or 12-panel)
  • User Manual (this document)

Note: E26/E27 sockets are not included and must be purchased separately if not already available.

Setup and Installation

The Leclstar LED Garage Light is designed for easy, tool-free installation into standard E26/E27 screw-in sockets.

  1. Power Off: Before installation, ensure the power to the light fixture circuit is turned off at the breaker or switch.
  2. Identify Socket: Locate a standard E26 or E27 screw-in light bulb socket where you intend to install the garage light.
  3. Screw In: Carefully screw the LED Garage Light into the E26/E27 socket clockwise until it is snug. Do not overtighten. No additional tools or wiring are required.
Installation diagram showing the LED Garage Light being screwed into an E26 socket without tools.
Figure 1: Easy installation into an E26/E27 socket. No tools needed.

Operating Instructions

Once installed and power is restored, the LED Garage Light will illuminate. Its unique deformable design allows for adjustable light direction.

  1. Turn On/Off: Use the wall switch connected to the E26/E27 socket to turn the light on or off.
  2. Adjust Panels: The individual LED panels can be manually adjusted up to 90 degrees. Gently pivot each panel to direct light precisely where needed. This allows for 360-degree illumination and flexible light coverage.
Diagram illustrating the adjustable light direction of the LED Garage Light, showing panels at 0, 45, and 90-degree angles.
Figure 2: Adjustable light direction with panels pivoting up to 90 degrees.
Image showing the LED Garage Light with panels rotated at 0, 45, and 90 degrees for omnidirectional illumination.
Figure 3: Omnidirectional illumination achieved by rotating panels.

Maintenance

The LED Garage Light is designed for long-lasting performance with minimal maintenance.

  • Cleaning: Ensure the power is off before cleaning. Use a soft, dry cloth to wipe the light fixture. Do not use abrasive cleaners or solvents.
  • Heat Dissipation: The light features a hollow ventilation design for efficient heat dissipation. Avoid obstructing the ventilation areas.
  • Panel Handling: While the panels are adjustable, avoid excessive force when repositioning them to prevent damage.
Diagram illustrating the fast heat dissipation design with hollow ventilation and airflow arrows. A warning states not to touch panels after long use due to heat.
Figure 4: Fast heat dissipation design with hollow ventilation. Panels may be hot after prolonged use.
Cross-section view of the LED light showing 144 high-end LEDs, PC housing, and an efficient cooling system for heat dissipation.
Figure 5: Internal view highlighting efficient heat dissipation components.

Troubleshooting

Light does not turn on:
  • Check if the power switch is on.
  • Ensure the light is securely screwed into the E26/E27 socket.
  • Verify that the circuit breaker for the light fixture is not tripped.
  • Test the socket with another working bulb to confirm the socket is functional.
Light flickers:
  • Ensure the light is securely screwed into the E26/E27 socket.
  • Check for loose wiring in the socket or switch (consult a qualified electrician if unsure).
  • Verify that the voltage supply is stable and within the AC85-265V range.
Light output is dim:
  • Ensure all adjustable panels are fully extended and positioned for maximum illumination.
  • Check if the light fixture or panels are covered in dust or debris and clean them as per maintenance instructions.

Specifications

FeatureSpecification
Model NumberLED Garage Light
Brand NameLeclstar
Wattage Options80W / 150W (depending on model)
Lumen Output8000LM (80W) - 15000LM (150W)
Color Temperature6500K Daylight
VoltageAC85-265V
Power SourceAC
Base TypeE26/E27
Light SourceLED bulbs (72-152 top-level LED chips)
Body MaterialAluminum, ABS Plastic, PC Lens
Is DimmableNo
Switch TypeNone (controlled by external switch)
LED Panel Adjustable Angle0°- 90°
Lighting Coverage Area360°
Lifetime50,000+ hours
CertificationCE
Dimensions (150W model)Width: 32cm (12.59in), Height: 10cm (3.93in)
ApplicationsGarage, Warehouse, Parking Lot, Exhibition Hall, Home, Workshop, Supermarket, Attic, etc.
Dimension diagram for the 150W LED Garage Light, showing a width of 32cm (12.59in) and a height of 10cm (3.93in).
Figure 6: Dimensions of the 150W LED Garage Light.
Collage of images showing various applications for the LED Garage Light, including front door, garage, warehouse, workshop, supermarket, and attic.
Figure 7: Versatile applications for the LED Garage Light.

User Tips

  • For optimal light distribution in large spaces, consider installing multiple units or choosing a model with more panels.
  • Experiment with different panel angles to find the best illumination for your specific task or area.
  • The high brightness of these lights makes them suitable for areas requiring significant illumination, such as workshops or storage facilities.

Warranty and Support

This Leclstar LED Garage Light comes with a 1-year warranty from the date of purchase, covering manufacturing defects under normal use.

For warranty claims, technical support, or any questions regarding your product, please contact the seller or retailer from whom you purchased the item. Please retain your proof of purchase for warranty validation.

Related Documents - LED Garage Light

Preview Leclstar Star Moon String Lights User Manual - Setup and Operation
Comprehensive user manual for Leclstar Star Moon String Lights, covering operating procedures, battery installation, and important precautions for safe and effective use.
Preview Leclstar PG30 Wake-up Light Sound Machine User Manual
Comprehensive user manual for the Leclstar PG30 Wake-up Light Sound Machine. Learn how to set alarms, use the sunrise simulator, white noise features, ambient light, and sleep timer. Includes safety information.
Preview Maxxima E26 Garage Light Installation Guide - MLB-G8000D
Comprehensive installation guide for the Maxxima E26 Garage Light (Model MLB-G8000D), detailing safety warnings, cautions, step-by-step installation procedures, and warranty information. Suitable for non-ballasted E26 bulb sockets.
Preview FLOS Luminator Floor Lamp - Installation Guide & Technical Specs
FLOS Luminator floor lamp: Installation, usage, and technical specifications. Learn about safe setup, bulb compatibility (E27/E26, HSGSR/SBLED), and cleaning for this classic 1954 design by Achille & Pier Giacomo Castiglioni.
Preview Artemide Logico Ceiling Light Installation and Bulb Guide
Comprehensive guide for installing and selecting bulbs for Artemide Logico Micro, Mini, and standard ceiling lights. Includes safety precautions and assembly instructions.
Preview JOYON E27 Hanging Light Installation Manual
Step-by-step instructions for installing the JOYON E27 hanging light fixture. Includes notes on bulb compatibility and important safety warnings.