ASYPDZSW NAD-JRC4580

Contents

NAD-JRC4580 Treble and Bass Preamplifier User Manual

Model: NAD-JRC4580 | Brand: ASYPDZSW

1. Introduction

This manual provides detailed instructions for the ASYPDZSW NAD-JRC4580 Treble and Bass Single-ended Class A Preamplifier. This high-fidelity preamplifier is engineered to deliver clear high, medium, and low audio levels with precise treble and bass adjustment capabilities. A key feature of its NAD-based circuit design is the ability to adjust tone without significantly altering the midrange (human voice), ensuring a natural and balanced sound profile. The product is available as a DIY kit for electronics enthusiasts or as a pre-assembled finished board for immediate integration into an audio system.

2. Package Contents

The NAD-JRC4580 preamplifier is offered in two distinct configurations:

  • DIY Kit: This package includes the bare Printed Circuit Board (PCB) and all necessary electronic components such as audiophile capacitors (e.g., Japanese ruby, Italian AV), military industry 718 factory copper foot metal film resistors, and the JRC4580DD op-amp. Please note that potentiometers are NOT included in the DIY kit. Assembly and soldering are required.
  • Finished Board: This option provides a fully assembled, soldered, and tested preamplifier board. It comes complete with the ALPS Type-16 potentiometers pre-installed.
NAD-JRC4580 preamplifier DIY kit components laid out on the bare PCB, illustrating parts for assembly.
Figure 2.1: DIY Kit Components on PCB
Finished NAD-JRC4580 preamplifier board with three ALPS Type-16 potentiometers for Bass, Treble, and Volume control. Shows input/output terminals and power input.
Figure 2.2: Finished Preamplifier Board

3. Specifications

Feature Detail
Model Number NAD-JRC4580
Channels 2 (2.0 Stereo)
Maximum Power Per Channel No Power (Preamplifier)
Brand Name ASYPDZSW
Package Type DIY Kit or Finished Board
Origin Mainland China
Certification NONE
Treble Adjustment Range ±10dB
Bass Adjustment Range ±15dB
Potentiometer Functions Bass, Treble, Volume
Potentiometer Spacing (L-R) 40mm, 50mm
Line Gain 8dB
Operating Voltage AC 15V-0-15V (Dual AC 15V)
Board Dimensions 135mm x 57mm
Op-Amp JRC4580DD (Japanese original)
Potentiometer Type ALPS Type-16 (for Finished Board)

4. Setup Instructions

4.1 For DIY Kit Assembly

If you have purchased the DIY kit, careful assembly and soldering are required. Ensure you possess the necessary tools (e.g., soldering iron, solder, desoldering wick, multimeter) and fundamental electronics knowledge before proceeding.

  1. Component Identification: Carefully refer to the PCB markings and component values to correctly identify each part (resistors, capacitors, op-amp, etc.).
  2. Soldering: Solder components onto the PCB, typically starting with smaller components like resistors and diodes, then progressing to larger ones such as capacitors and the op-amp socket (if provided). Pay close attention to polarity for electrolytic capacitors and the op-amp.
  3. Power Connection: Connect your dual AC 15V-0-15V power supply to the designated AC input screw terminals labeled 'AC', 'GND', and 'AC'. Ensure the center tap (0V) of your transformer is connected to the 'GND' terminal. Verify correct voltage and polarity before powering on.
  4. Audio Input/Output: Connect your audio source (e.g., CD player, DAC) to the 'RIN' (Right Input) and 'LIN' (Left Input) terminals. Connect the preamplifier's output to your power amplifier's input using the 'ROUT' (Right Output) and 'LOUT' (Left Output) terminals.
  5. Potentiometer Installation: If using external potentiometers, connect them to the designated points for Bass, Treble, and Volume control.
Angled view of the NAD-JRC4580 preamplifier DIY kit, showing various electronic components and the PCB.
Figure 4.1: DIY Kit Components Overview
Another angled view of the NAD-JRC4580 preamplifier DIY kit, with components scattered on and around the PCB.
Figure 4.2: DIY Kit Components Detail

4.2 For Finished Board

The finished board comes pre-assembled and tested, simplifying the setup process. Follow these steps for connection:

  1. Power Supply: Connect a dual AC 15V-0-15V power supply to the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.