GVDA GD109

Contents

GVDA GD109 Pen Type Digital Multimeter

Model: GD109

Instruction Manual

1. Introduction

The GVDA GD109 is a versatile pen-type digital multimeter designed for safe and accurate measurement of various electrical parameters. It features True RMS measurement, smart auto-ranging, and a clear HD display. This manual provides essential information for operating and maintaining your multimeter.

GVDA Pen Type Digital Multimeter with test leads

Figure 1: GVDA GD109 Pen Type Digital Multimeter

2. Safety Information

WARNING: To avoid possible electric shock or personal injury, please observe the following safety instructions:

  • Read this manual carefully and pay special attention to safety warning information before using the meter.
  • Operate the meter according to the instructions. Otherwise, the protection function provided by the instrument may be damaged or weakened.
  • Do not measure voltage values that exceed 60V DC or 30V AC.
  • The meter conforms to IEC61010-1, CAT III 600V overvoltage standard, and Pollution Level 2.
  • Ensure the operating environment conditions are within specifications: 0~40°C temperature (<80% RH, <10°C non-condensing) and altitude < 2000m.
  • The maximum voltage between terminals and earth ground is 600V.

3. Product Overview

The GD109 multimeter is designed for ease of use and portability. Key components and display features are outlined below.

3.1 Components

Product Introduction diagram labeling parts: Input jack, On/Off, Data hold/Flashlight, Range switching, Display, Signal intensity indicator, NCV Sensor.

Figure 2: Multimeter Components

  • Input Jack: For connecting test leads.
  • On / Off Button: Powers the device on or off.
  • Data Hold / Flashlight Button: Short press to hold data, long press to activate flashlight.
  • Range Switching Button (FUNC): Cycles through measurement functions.
  • Display: Shows measurement readings and indicators.
  • Signal Intensity Indicator: Visual indication of signal strength (e.g., NCV).
  • NCV Sensor: For non-contact voltage detection.
  • Comfort Buttons: Ergonomically designed for ease of use.

3.2 HD Display

The multimeter features a clear HD display with 4000 counts, providing precise and easy-to-read measurements. Indicators for various functions like voltage, resistance, capacitance, frequency, NCV, and live wire detection are clearly visible.

HD Display of the multimeter showing various measurement indicators.

Figure 3: HD Display

4. Setup

4.1 Battery Installation

The GD109 multimeter requires 2 x 1.5V AAA batteries (not included). To install or replace batteries:

  1. Locate the battery compartment cover on the back of the multimeter.
  2. Use a screwdriver to open the cover.
  3. Insert two AAA batteries, ensuring correct polarity (+/-).
  4. Replace the battery compartment cover and secure it.
Battery replacement design, showing the battery compartment with AAA batteries.

Figure 4: Battery Replacement

5. Operating Instructions

The GD109 features an auto-ranging smart measurement mode, but specific functions can also be selected manually.

5.1 Smart (AUTO) Measurement

In this mode, the multimeter automatically identifies the measurement signal for DC voltage, AC voltage, resistance, and continuity. Simply connect the test leads to the circuit, and the meter will display the appropriate reading.

Smart (AUTO) measurement mode in use, showing automatic signal identification.

Figure 5: Smart (AUTO) Measurement

5.2 DC Voltage Test

Connect the red test lead to the positive point and the black test lead to the negative point of the DC circuit. The meter will display the DC voltage reading.

DC voltage test in progress.

Figure 6: DC Voltage Test

5.3 AC Voltage Test

Connect the test leads across the AC voltage source. The meter will display the AC voltage reading.

AC voltage test in progress.

Figure 7: AC Voltage Test

5.4 Resistance Test

Ensure the circuit is de-energized. Connect the test leads across the component to measure its resistance. The meter will display the resistance in Ohms (Ω).

Resistance test in progress.

Figure 8: Resistance Test

5.5 Capacitance Measurement

Ensure the capacitor is discharged before testing. Connect the test leads across the capacitor. The meter will display the capacitance in Farads (F).

Capacitance measurement in progress.

Figure 9: Capacitance Measurement

5.6 Frequency Test

Connect the test leads to the circuit where you want to measure frequency. The meter will display the frequency in Hertz (Hz).

5.7 Diode Measurement

Connect the test leads across the diode. The meter will display the forward voltage drop of the diode.

Diode measurement in progress.

Figure 10: Diode Measurement

5.8 Continuity Test

Connect the test leads across the circuit or component. If there is continuity (low resistance), the meter will emit an audible beep.

Continuity test (on and off beep) in progress.

Figure 11: Continuity Test

5.9 NCV (Non-Contact Voltage) Measurement

Hold the NCV sensor near a live wire or electrical outlet. The meter will detect the presence of AC voltage without physical contact, indicated by the signal intensity indicator and an alarm beep.

NCV measurement in action, showing the meter detecting voltage near an outlet.

Figure 12: NCV Measurement

5.10 Non-Contact Phase Sequence Detection

This function helps determine the phase sequence in three-phase systems without direct contact.

Detailed steps for non-contact phase sequence detection (PA, PAB, PABC indications).

Figure 13: Non-Contact Phase Sequence Detection

  1. Display the "PA" symbol with the "A" letter flashing and stick the sensing probe to the first phase line, waiting for a beep.
  2. Display the "PAB" symbol with the "B" letter flashing and stick the sensing probe to the second phase line and wait for a beep.
  3. Display the "PABC" symbol with the "C" letter flashing and stick the sensing probe to the second phase line and wait for a long beep.

5.11 Live Wire Detection

The multimeter can detect live wires. When a weak electric field signal is detected, it will display "--L"; the buzzer will sound slowly and the green light will turn on. When a strong electric field signal is detected, it will display "--H"; the buzzer will sound quickly and the red light will turn on.

Live wire detection, illustrating 'L' for weak signal and 'H' for strong signal.

Figure 14: Live Wire Detection

5.12 Data Hold

Press the Data Hold button (often combined with Flashlight) to freeze the current reading on the display.

5.13 Auto Power Off

The multimeter will automatically power off after a period of inactivity to conserve battery life.

5.14 Flashlight

Long press the Flashlight button to turn on the built-in flashlight for illumination in dimly lit areas.

Flashlight feature in use.

Figure 15: Flashlight in Use

6. Specifications

Feature Specification
Brand NameGVDA
Model NumberGD109
Operating ModeAuto Range
Display TypeDigital Display
Display Counts4000 counts
Sampling RateApprox. 3 times/second
DC Voltage Range0.8V~600V (4V, 40V, 400V, 600V) ±(0.5% +3)
AC Voltage Range0.8V~600V (4V, 40V, 400V, 600V) ±(0.8%+3)
Measuring Resistance Range4000Ω/40KΩ/400KΩ/4MΩ ±(1.0%+5); 40MΩ ±(1.5%+10)
Measuring Capacitance Range40nF/400nF/4uF/40uF/400uF/4mF ±(3.0+5)
Frequency Range40Hz/400Hz/4KHz/40kHz/400kHz/4MHz ±(1.0%+3)
Measuring Inductance RangeNo
DC CurrentNo
AC CurrentNo
Continuity TestYes
Diode MeasurementYes
NCV MeasurementYes
Non-contact Phase Sequence DetectionYes
Live Wire DetectingYes
Data HoldYes
Auto Power OffYes
FlashlightYes
True RMSYes
Power Requirement2 x 1.5V AAA batteries (Not include)
Dimensions22*30*172mm
Operating Temperature0 - 40 ℃
Storage Temperature & Humidity-10~60°C (<70% RH, remove the battery)
Temperature Coefficient0.1 accuracy/°C (<18°C or >28°C)
Over Range Indication"OL"
Low Battery IndicationYes
Input Polarity IndicationDisplay "-"
Environment Condition of UseCAT. III 600V; Pollution level 2, Altitude < 2000m
CertificationCE, FCC, RoHS

7. Maintenance

  • Cleaning: Wipe the meter with a dry, soft cloth. Do not use abrasives or solvents.
  • Battery Replacement: Replace batteries promptly when the low battery indicator appears to ensure accurate readings. Refer to Section 4.1 for instructions.
  • Storage: If the meter is not used for a long period, remove the batteries to prevent leakage and store it in a cool, dry place within the specified storage temperature and humidity.
  • Calibration: For professional use, periodic calibration by qualified personnel is recommended to maintain accuracy.

8. Troubleshooting

  • Meter does not power on: Check if batteries are installed correctly and have sufficient charge. Replace if necessary.
  • "OL" displayed: This indicates an over-range condition. The measured value exceeds the meter's maximum range for the selected function.
  • Inaccurate readings: Ensure test leads are properly connected and not damaged. Check battery level. Verify the correct measurement function is selected.
  • No NCV detection: Ensure the NCV sensor is held close enough to the live source. Check battery level.

9. User Tips

  • Always start with the highest range when measuring an unknown voltage or current to prevent damage to the meter.
  • For resistance and continuity tests, ensure the circuit is de-energized to avoid false readings or damage.
  • When measuring capacitance, always discharge the capacitor before connecting the multimeter.
  • Utilize the flashlight feature in dark environments for better visibility and safety.
  • The compact pen-type design makes it ideal for quick checks and tight spaces.

10. Warranty and Support

The GVDA GD109 Pen Type Digital Multimeter comes with a 24-month manufacturer's limited warranty for defective items, excluding items damaged or misused after receipt. Accessories are covered by a 3-month warranty.

For technical support or warranty claims, please contact your retailer or the manufacturer directly with your order number and a description of the issue.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.