SUNSUN HBL-301, HBL-302, HBL-303, HBL-401, HBL-402, HBL-403, HBL-501, HBL-502, HBL-601, HBL-701, HBL-702

Contents

SUNSUN HBL Series Replacement Filter Plate Instruction Manual

Models: HBL-301, HBL-302, HBL-303, HBL-401, HBL-402, HBL-403, HBL-501, HBL-502, HBL-601, HBL-701, HBL-702

Activated Carbon and Bio Media Biochemical Sheets for Aquarium Hang-On Back Filters

Introduction

This manual provides instructions for the proper installation, operation, and maintenance of SUNSUN HBL series replacement filter plates. These filter plates are designed for use with SUNSUN HBL hang-on back aquarium filters, offering both activated carbon and bio media for effective water purification.

Assortment of SUNSUN HBL replacement filter plates in their packaging.
Figure 1: Various SUNSUN HBL series replacement filter plates.

Setup and Installation

Before installing the new filter plate, ensure your SUNSUN HBL hang-on back filter is unplugged and removed from the aquarium. Follow these steps:

  1. Carefully open the filter housing of your SUNSUN HBL filter unit.
  2. Remove the old, used filter plate. Dispose of it responsibly.
  3. Unpack the new SUNSUN HBL replacement filter plate. Ensure you have the correct model for your filter (e.g., HBL-301, HBL-302, HBL-303, etc.).
  4. Rinse the new filter plate gently under clean, dechlorinated water to remove any manufacturing dust. Do not rinse with tap water containing chlorine, as this can harm beneficial bacteria.
  5. Insert the new filter plate into the designated slot within the filter housing. Ensure it sits securely and correctly, allowing water to flow through it as intended. The activated carbon side typically faces the incoming water flow for optimal chemical filtration.
  6. Close the filter housing securely.
  7. Re-attach the filter to your aquarium and plug it back in.
HBL-302/402 filter plate showing the carbon pad and plastic frame.
Figure 2: Example of a replacement filter plate (HBL-302/402) showing its components.

Operating Principles

The SUNSUN HBL replacement filter plates combine mechanical, chemical, and biological filtration:

  • Mechanical Filtration: The fibrous material of the filter pad traps particulate matter, debris, and uneaten food, keeping the water clear.
  • Chemical Filtration: The activated carbon within the filter plate absorbs odors, discolorations, and harmful organic compounds from the water.
  • Biological Filtration: The porous structure of the filter media provides a large surface area for beneficial bacteria to colonize. These bacteria convert toxic ammonia and nitrites into less harmful nitrates, maintaining a healthy aquatic environment.
Close-up of a filter plate showing activated carbon media within its grid structure.
Figure 3: Activated carbon media embedded within the filter plate.

Maintenance and Replacement

Regular maintenance is crucial for optimal filter performance and water quality. The filter plates should be replaced periodically.

Replacement Frequency:

  • It is recommended to replace the filter plate every 2-4 weeks, depending on the bio-load of your aquarium and water quality.
  • Do not replace all filter media simultaneously, as this can remove beneficial bacteria and lead to a "new tank syndrome" effect. If your filter uses multiple media types, replace them on a staggered schedule.

Replacement Procedure:

Follow the "Setup and Installation" steps for replacing the filter plate. When replacing, consider rinsing the new filter plate with old aquarium water to help seed beneficial bacteria, if possible, or use a bacterial starter product.

Troubleshooting

ProblemPossible CauseSolution
Reduced water flow from filterClogged filter plateReplace the filter plate. Ensure the filter intake is clear of debris.
Cloudy or discolored waterExpired activated carbon or insufficient mechanical filtrationReplace the filter plate. Perform a partial water change.
Unpleasant odors in aquariumExpired activated carbonReplace the filter plate.
High ammonia/nitrite levelsInsufficient biological filtration or filter media replaced too frequentlyEnsure filter is running continuously. Avoid replacing all media at once. Consider adding a bacterial starter.

Specifications

  • Type: Replacement Filter Plate (Activated Carbon & Bio Media)
  • Compatibility: SUNSUN HBL Series Hang-On Back Filters (HBL-301, HBL-302, HBL-303, HBL-401, HBL-402, HBL-403, HBL-501, HBL-502, HBL-601, HBL-701, HBL-702)
  • Material: Filter floss, activated carbon, plastic frame
  • Origin: Mainland China

Dimensions (Approximate):

Table showing width and length specifications for various HBL filter carbon plate models.
Figure 4: HBL Filter carbon plate parameters.
ModelWidth (cm)Length (cm)
HBL-30210.34.3
HBL-30312.55.6
HBL-50111.46.2
HBL-601159
HBL-701136.5

User Tips

  • Always keep spare filter plates on hand to ensure timely replacement and continuous optimal filtration.
  • When replacing, gently squeeze the old filter media in a bucket of old aquarium water to preserve some beneficial bacteria before discarding, then install the new media. This helps maintain biological balance.
  • Monitor your aquarium's water parameters (ammonia, nitrite, nitrate) regularly, especially after filter media changes, to ensure the biological filter is functioning effectively.

Warranty and Support

For specific warranty information or technical support regarding your SUNSUN HBL filter or replacement parts, please refer to the original product documentation that came with your filter unit or contact SUNSUN customer service directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.