ORIA Led alarm clock

Contents

ORIA LED Digital Smart Alarm Clock

Model: Led alarm clock

User Manual

Introduction

This manual provides comprehensive instructions for the ORIA LED Digital Smart Alarm Clock. It covers initial setup, detailed operating procedures, maintenance guidelines, troubleshooting tips, and product specifications to ensure you get the most out of your device. Please read this manual thoroughly before using the product and keep it for future reference.

Safety Information

  • Ensure the device is placed on a stable, flat surface to prevent accidental falls.
  • Keep the alarm clock away from water, high humidity, and direct heat sources to avoid damage.
  • Use only the provided USB cable for power. Do not use damaged cables or power adapters.
  • Do not attempt to disassemble or repair the device yourself. Refer all servicing to qualified personnel.
  • Keep out of reach of children.

Package Contents

Please check the package contents upon opening to ensure all items are present:

  • 1 x ORIA LED Digital Alarm Clock
  • 1 x USB Cable
  • 1 x User Manual (this document)
Package contents including the ORIA LED Digital Smart Alarm Clock, USB cable, and user manual.
Figure 1: Contents of the ORIA LED Digital Smart Alarm Clock package.

Product Overview

Familiarize yourself with the components and controls of your alarm clock:

Back view of the ORIA LED Digital Smart Alarm Clock with labels for buttons, ports, and features.
Figure 2: Rear view of the alarm clock with labeled controls and ports.

Controls and Ports:

  • Snooze/Light Button: Adjusts brightness, activates snooze, and enables automatic light-sensing mode.
  • UP Button: Navigates menus, switches temperature units (℃/℉), and changes display modes.
  • Down Button: Navigates menus and toggles energy-saving mode.
  • Set Button: Enters setting mode for time, date, and temperature.
  • Alarm Button: Activates/deactivates alarms and enters alarm setting mode.
  • Ambient Light Sensor: Automatically adjusts display brightness in auto-sensing mode.
  • Hanging Hole: Allows for wall mounting.
  • USB Charging Ports (Output): For charging external electronic devices.
  • Power Port (Input 5V): Connects to the USB power cable for primary operation.
  • CR2016 Battery Compartment: Houses the backup battery for time memory.
  • Detachable Stand: For desktop placement.

Setup

  1. Power Connection: Connect the provided USB cable to the Power Port (Input 5V) on the back of the alarm clock and plug the other end into a 5V USB power adapter (not included) or a powered USB port. The clock will only function when connected to an outlet.
  2. Backup Battery: The clock has a built-in CR2016 3V lithium battery. This battery is for time memory only and ensures the time continues to run after power off, eliminating the need to reset when power is restored. It does not power the display.
  3. Placement:
    • Desktop: Attach the detachable stand to the bottom of the clock for stable desktop placement.
    • Wall Mount: Use the hanging hole on the back of the clock to mount it on a wall.
Video 1: Demonstration of the removable stand and brightness adjustment.

Operating Instructions

1. Setting Time, Date, and Temperature

  1. Display Cycle: Single press the Set Button to cycle through Time, Date, and Temperature displays.
  2. Enter Setting Mode: Long press the Set Button to enter the setting mode. The first adjustable item will flash.
  3. Adjust Values: Use the UP and Down Buttons to adjust the flashing value.
  4. Navigate Settings: Single press the Set Button to move to the next setting item (12/24 hour system, hour, minute, year, month, day).
  5. Exit Setting Mode: After setting all desired values, stop pressing buttons for a few seconds, and the clock will automatically exit setting mode.
  6. Temperature Unit: In the temperature display interface, single press the UP Button to switch between Celsius (℃) and Fahrenheit (℉).

2. Setting Alarms and Snooze

The clock supports two independent alarm settings.

Image showing dual alarm functionality for different daily routines.
Figure 3: The clock supports dual alarms for various schedules.
  1. Activate/Deactivate Alarms: Single press the Alarm Button to cycle through: Alarm 1 ON, Alarm 2 ON, Alarm 1 & 2 ON, All Alarms OFF. A bell icon will appear on the display when an alarm is active.
  2. Set Alarm Time: Long press the Alarm Button to enter alarm setting mode.
  3. Adjust Alarm Values: Use the UP and Down Buttons to adjust the hour, minute, and snooze time for Alarm 1, then repeat for Alarm 2.
  4. Snooze Function: When an alarm sounds, press the Snooze/Light Button to activate snooze. The snooze duration can be set from 5 to 60 minutes during alarm setup. The alarm ringing time is 1 minute.
Image demonstrating the easy snooze function for extra sleep time.
Figure 4: Easy snooze function for additional sleep.

3. Adjusting Brightness

Image showing three levels of adjustable brightness for the clock display.
Figure 5: Three adjustable brightness levels for optimal viewing.
  • Manual Brightness: Single press the Snooze/Light Button to cycle through 3 levels of brightness (Bright, Medium, Low).
  • Automatic Light-Sensing Mode: Long press the Snooze/Light Button to activate the automatic light-sensing mode. An icon will appear below the two dots in the middle of the time display, indicating that the brightness will automatically adjust based on the ambient light.

4. Display Modes (DP-1, DP-2, DP-3)

Single press the UP Button to switch between the three display modes:

  • DP-1: Displays time for 10 seconds, then date for 2 seconds, then temperature for 2 seconds, continuously cycling.
  • DP-2: Always displays time, date, and temperature simultaneously without conversion.
  • DP-3: Always displays the time. Pressing the Set Button will temporarily switch to another display item, but after 15 seconds of no operation, it will automatically revert to the time display.

5. Energy-Saving Mode

Single press the Down Button to toggle the energy-saving mode ON (ONSD) or OFF (SD).

  • ONSD (Energy-Saving ON): The LED display will automatically turn off after 15 seconds. Pressing any button will illuminate the LED for 15 seconds. (Note: This mode does not support sound control for activation).
  • SD (Energy-Saving OFF): The display remains continuously on when plugged in.

6. USB Charging Port

The alarm clock features a built-in USB output port on the side, allowing you to charge other electronic devices such as smartphones or tablets.

Image showing the alarm clock charging a smartphone via its USB output port.
Figure 6: The clock's USB port can charge other devices.

Maintenance

  • Clean the clock's surface with a soft, dry, lint-free cloth.
  • Do not use abrasive cleaners, solvents, or chemical sprays, as these may damage the finish or electronic components.
  • Ensure the USB ports are free from dust and debris.

Troubleshooting

Problem Possible Solution
Clock display is off or not working. Ensure the USB power cable is securely connected to a working power outlet. The internal button battery only provides time memory, not power for the display.
Display is too dim or too bright. Single press the Snooze/Light Button to manually adjust brightness. Long press it to enable or disable the automatic light-sensing mode.
Alarm is not sounding. Single press the Alarm Button to check if Alarm 1 or Alarm 2 (or both) are activated. A bell icon should be visible on the display. Long press the Alarm Button to re-set the alarm time.
Time/Date/Temperature is incorrect. Long press the Set Button to enter setting mode and adjust the time, date, and temperature as needed.
Energy-saving mode not working as expected. Single press the Down Button to toggle between ONSD (Energy-Saving ON) and SD (Energy-Saving OFF). Remember, in ONSD mode, the display turns off after 15 seconds and reactivates only by button press.

Specifications

Feature Detail
Model Number Led alarm clock
Display Type Digital LED
Screen Type LED
Dimensions (Length x Width) 160mm x 60mm (approx. 6.3in x 2.4in)
Weight 168g (approx. 0.37 lbs)
Power Input 5V via USB cable
Backup Battery CR2016 3V (for time memory only)
Temperature Range -9℃ to 50℃ (15.8℉ to 122℉)
Alarm Functions Dual alarms, Snooze (5-60 minutes)
Brightness Levels 3 manual levels + Automatic light-sensing mode
Additional Features USB output charging port, Time memory function, Wall mountable
Package Dimensions 17cm (L) x 8cm (W) x 4cm (H)
Package Weight 0.168 kg

User Tips

  • For continuous display, always ensure the clock is plugged into an active power outlet. The button battery is solely for retaining time settings during power interruptions, not for powering the main display.
  • Utilize the automatic brightness adjustment feature for optimal visibility throughout the day and night without needing to manually change settings.
  • When using the USB charging port, be aware that it draws power from the clock's main supply, which might affect the overall power consumption.

Warranty and Support

For warranty information, technical assistance, or any product-related inquiries, please contact your original retailer or visit the official ORIA website for support resources.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.