JUNCTEK JDS2900

Contents

JUNTEK JDS2900 Series DDS Function Signal Generator User Manual

Model: JDS2900 Series (15MHz, 30MHz, 40MHz, 50MHz, 60MHz)

1. Introduction

The JUNTEK JDS2900 series Dual-channel Function Signal Generator is a versatile instrument combining multiple functions including Function Signal Generator, Arbitrary Waveform Generator, Pulse Generator, Sweep, Counter, and Frequency Meter. Utilizing Direct Digital Synthesizer (DDS) technology, it delivers stable, precise, pure, and low-distortion signals. This instrument is an essential tool for electronics engineers, electronic laboratories, and for teaching and research purposes.

The JDS2900 features a 320*240 2.4-inch TFT color LCD display, capable of simultaneously showing parameters for both Channel 1 (CH1) and Channel 2 (CH2). It supports the reproduction of custom waveforms and offers completely independent dual-channel output with synchronizing operation. The device includes 60 groups of arbitrary wave storage, each with a memory depth of 2048*14 bits.

High frequency accuracy (up to 10-6 magnitude) and resolution (0.01uHz) ensure precise signal generation. The amplitude resolution is 1mV, with an amplitude range of 2mVpp to 20Vpp. The duty cycle for each channel can be independently adjusted with a resolution of 0.1%.

Advanced features include linear and logarithmic sweep functions (0.1s-999.9s sweep time) with forward, backward, and roundtrip directions, as well as a pulse train burst output function (1 to 1048575 arbitrary pulse trains). Measurement capabilities include signal frequency, cycle, positive/negative pulse width, and duty cycle within a 1Hz to 100MHz range. It also provides a digital signal output function with a CMOS output range of 0-10V.

The instrument can store 100 groups of user-defined parameters for quick recall. An arbitrary wave editing function allows users to create custom waveforms on a PC and download them to the instrument. Communication with a PC is supported for instrument control. All signal outputs are protected against short-circuits for up to 60 seconds under load.

The JDS2900 series is available in various maximum sine wave frequencies: 15MHz, 30MHz, 40MHz, 50MHz, and 60MHz. The maximum square wave frequency is 25MHz, with a 266MSa/s sampling rate and 14-bit vertical resolution.

2. Safety Information

  • Always operate the device within the specified voltage and current limits.
  • Ensure proper grounding to prevent electric shock.
  • Do not open the device casing unless you are a qualified technician. There are no user-serviceable parts inside.
  • Avoid exposing the device to moisture, extreme temperatures, or direct sunlight.
  • Use only the provided power adapter and cables.
  • Disconnect power before cleaning or when not in use for extended periods.

3. Product Overview

3.1. Device Dimensions and Weight

JDS2900 Signal Generator dimensions: 2.1in/5.4cm height, 5.6in/14.3cm length, 3.7in/9.5cm width. Weight: 400g.
Figure 1: JDS2900 Signal Generator dimensions and weight. The device measures approximately 5.4 cm (2.1 inches) in height, 14.3 cm (5.6 inches) in length, and 9.5 cm (3.7 inches) in width. Its weight is 400g.

3.2. Front and Rear Panel Layout

Front and rear panel layout of the JDS2900 Signal Generator. Front panel shows LCD, menu buttons, knob, shortcut keys, CH1 and CH2 output, and signal/TTL measurement interfaces. Rear panel shows 5V power input, USB communication interface, and ON/OFF switch.
Figure 2: Detailed view of the JDS2900 Signal Generator's front and rear panels. The front panel includes the 2.4-inch LCD screen, menu buttons, an adjustment knob, shortcut keys, and output interfaces for CH1, CH2, and signal/TTL measurement. The rear panel features the 5V power input, USB communication interface, and the ON/OFF switch.
Top-down view of the JDS2900 Signal Generator, showing the control panel and display.
Figure 3: Top-down perspective of the JDS2900, highlighting the user interface with its display and control buttons.
Side view of the JDS2900 Signal Generator, showing the output ports.
Figure 4: Side view of the JDS2900, illustrating the various output ports for signal generation.
Another side view of the JDS2900 Signal Generator, showing the power input and USB port.
Figure 5: Opposite side view of the JDS2900, detailing the power input and USB communication port.

4. Setup

4.1. Unpacking and Inspection

Upon receiving your JDS2900 series signal generator, carefully unpack all components and inspect them for any signs of damage. If any items are missing or damaged, please contact your supplier immediately.

4.2. Package Contents

Contents of the JDS2900 Signal Generator package, including the main unit, power adapter, BNC-BNC cable, USB data cable, and two BNC-Clip cables.
Figure 6: The standard package includes the JDS2900 DDS Signal Generator unit, a power adapter (Input: 100~240V~50/60Hz, Output: 5.0V-0.2A), one BNC-BNC cable, one USB data cable, and two BNC-Clip cables.
  • 1 x JDS2900 Series DDS Signal Generator
  • 1 x Power Adapter (Input: 100~240V~50/60Hz, Output: 5.0V-0.2A)
  • 1 x BNC-BNC Cable
  • 1 x USB Data Cable
  • 2 x BNC-Clip Cables

4.3. Power Connection

  1. Connect the provided power adapter to the "DC5V" power input port on the rear panel of the signal generator.
  2. Plug the power adapter into a suitable electrical outlet.
  3. Flip the "ON/OFF" switch on the rear panel to the "ON" position to power on the device.
JDS2900 Signal Generator connected to a power bank for portable charging.
Figure 7: The JDS2900 can be powered by a standard 5V power adapter or a portable power bank for field use.

4.4. PC Connection (Optional)

The JDS2900 can be connected to a PC via the USB communication interface for advanced control and arbitrary waveform editing.

  1. Connect one end of the USB data cable to the USB port on the rear panel of the signal generator.
  2. Connect the other end of the USB data cable to an available USB port on your computer.
  3. Install the PC software provided by the manufacturer (usually available for download from their website). This software allows for secondary programming control and arbitrary waveform drawing.
Diagram showing the JDS2900 Signal Generator connected to a computer via USB, with PC software for control.
Figure 8: Connecting the JDS2900 to a computer for PC software control and advanced waveform editing.

5. Operating Instructions

5.1. Basic Operation

The JDS2900 features a user-friendly interface with a 2.4-inch color LCD, function buttons, a shuttle knob, and shortcut keys for efficient operation.

  • LCD Screen: Displays parameters for both CH1 and CH2 simultaneously.
  • Menu Buttons: Navigate through various settings and functions.
  • Adjustment Knob: Used for continuous adjustment of parameters like frequency, amplitude, and duty cycle.
  • Shortcut Keys: Provide quick access to frequently used functions.
  • CH1/CH2 Output Interfaces: Connect to external devices (e.g., oscilloscopes) using BNC cables.
  • Signal/TTL Measurement Interface: Used for external signal measurement.

5.2. Dual Channel Waveform Output

The two channels (CH1 and CH2) are completely independent, allowing for simultaneous output of the same or different waveforms. This is useful for applications requiring multiple synchronized or independent signals.

Video 1: Demonstration of dual-channel waveform output, frequency sweep, pulse function, and burst function using the JDS2900 signal generator connected to an oscilloscope. The video illustrates how to adjust parameters and observe the resulting waveforms.

5.3. Frequency Sweep Function

The JDS2900 supports frequency sweep functions, allowing the output frequency to change linearly or logarithmically over a specified range. The sweep frequency range is 0 to 60 MHz.

  • Sweep Channel: CH1 or CH2
  • Sweep Type: Linear sweep, logarithmic sweep
  • Sweep Time: 0.1s to 999.9s
  • Setting Range: Any setting between the maximum output frequency of the corresponding model of the starting point (0.01Hz) and the end point.
  • Sweep Direction: Forward, reverse, and round trip.

5.4. Pulse Function

The pulse width is digitalized and precisely adjustable, offering fine control over pulse characteristics.

  • Pulse Width Adjustment Range: 100nS~4000S (for 15MHz model), 50nS~4000S (for 30MHz model), 40nS~4000S (for 40MHz model), 30nS~4000S (for 50MHz model), 25nS~4000S (for 60MHz model).
  • Duty Cycle Adjustment Range: 0.1%~99.9%

5.5. Burst Function

The trigger function allows for the output of waveforms in bursts of any number of periods.

  • Number of Pulses: 1-1048575
  • Burst Mode: Manual burst, CH2 burst, external burst (AC), external burst (DC)

5.6. Measurement Functions

The JDS2900 can measure frequency, period, and duty cycle of external signals.

  • Frequency Measurement Range: 1Hz~100MHz
  • Measurement Accuracy: Gate time 0.01S~10s continuously adjustable.
  • Counting Range: 0-4294967295
  • Coupling Method: DC and AC coupling methods.
  • Counting Method: Manually.
  • Input Signal Voltage Range: 2Vpp~20Vpp.
  • Pulse Width Measurement: 0.01us resolution, measure up to 20s.
  • Period Measurement: 0.01us resolution, measure up to 20s.

6. Maintenance

6.1. General Care

  • Keep the instrument clean and free from dust. Use a soft, dry cloth for cleaning the exterior.
  • Avoid using abrasive cleaners or solvents that could damage the casing or screen.
  • Store the device in a cool, dry environment when not in use.

6.2. Software Updates

Periodically check the manufacturer's website for any available firmware or software updates for your JDS2900 series signal generator. Updates may provide new features, performance improvements, or bug fixes.

7. Troubleshooting

ProblemPossible CauseSolution
Device does not power on.Power adapter not connected or faulty; power switch off.Ensure power adapter is securely connected and plugged into a live outlet. Check power switch position. Try a different power outlet.
No signal output.Output channel disabled; incorrect parameters set; faulty cable connection.Verify that the desired channel (CH1/CH2) is enabled. Check waveform parameters (frequency, amplitude, offset). Ensure BNC cables are securely connected.
PC software not connecting.USB cable faulty; drivers not installed; incorrect COM port selected.Ensure USB cable is connected. Install necessary drivers. Select the correct COM port in the PC software. Restart both the device and PC.
Display is blank or frozen.Software error; hardware malfunction.Power cycle the device (turn off, wait 10 seconds, turn on). If the problem persists, contact technical support.

8. Specifications

8.1. General Specifications

FeatureDescription
Display Type2.4 inch TFT color LCD display
Stored Parameters100 groups (00 to 99, 00 loaded by default on power-on)
Arbitrary Waveforms1 to 60 total groups (15 groups by default on power-on)
Interface ModeUSB to serial interface
Extension InterfaceTTL level mode serial interface for user secondary development
Communication SpeedStandard 115200bps
ProtocolCommand line, public protocol
Power SupplyDC5V ±0.5V
Manufacturing TechnologySurface mount technology, large-scale integrated circuits, high reliability, long service life
Prompt ToneUser configurable (on/off by program)
Operating CharacteristicsAll key operations, knob continuous adjustment
Environmental ConditionsTemperature: 0~40℃, Humidity: <80%

8.2. Frequency Characteristics

ParameterJDS2900-15MJDS2900-30MJDS2900-40MJDS2900-50MJDS2900-60M
Sine wave frequency range0~15MHz0~30MHz0~40MHz0~50MHz0~60MHz
Square/Triangle wave frequency range0~15MHz0~25MHz0~25MHz0~25MHz0~25MHz
Pulse/TTL digital wave frequency range0~6MHz0~6MHz0~6MHz0~6MHz0~6MHz
Arbitrary frequency range0~6MHz0~6MHz0~6MHz0~6MHz0~6MHz
Pulse width adjustment range100nS~4000S50nS~4000S40nS~4000S30nS~4000S25nS~4000S
Square wave rise time≤25ns≤15ns≤10ns≤10ns≤10ns
Minimum frequency resolution0.01uHz (0.00000001Hz)
Frequency accuracy±20ppm
Frequency stability±1ppm/3hours

8.3. Waveform Characteristics

ParameterValue
Waveform TypeSine, Square, Pulse (adjustable duty cycle, precise adjustment of pulse width and period), Triangular, Partial Sine, CMOS, DC level (set DC amplitude by adjusting offset), Half Wave, Full Wave, Positive Staircase, Anti-ladder, Noise, Exponential Rise, Exponential Drop, Multisonic, Symplectic Pulse, Lorenz Pulse, and 60 arbitrary waveforms.
Wave Length2048 points
Waveform Sampling Rate266MSa/s
Waveform Vertical Resolution14-bits
Square Wave and Pulse Wave Overshoot≤5%
Sine Wave Harmonic Suppression≥45dBc (<1MHz); ≥40dBc (1MHz~20MHz)
Sine Wave Total Harmonic Distortion<1% (20Hz~20kHz, 0dBm)
Saw-tooth Wave Linearity≥98% (0.01Hz~10kHz)

8.4. Output Characteristics

ParameterValue
Sine Wave Amplitude Range (Frequency < 11MHz)2mVpp~20Vpp
Sine Wave Amplitude Range (11MHz ≤ Frequency < 31MHz)2mVpp~10Vpp
Sine Wave Amplitude Range (31MHz ≤ Frequency)2mVpp~5Vpp
Square/Triangle Wave Amplitude Range (Frequency ≤ 10MHz)2mVpp~20Vpp
Square/Triangle Wave Amplitude Range (10MHz ≤ Frequency ≤ 25MHz)2mVpp~10Vpp
Amplitude Resolution1mV
Amplitude Stability±0.5%/5 hours
Flatness of Amplitude±5% (<10MHz); ±10% (>10MHz)
Output Impedance50Ω ±10% (typical)
ProtectionAll signal outputs can work within 60 seconds when the load is short-circuited.

8.5. DC Offset Characteristics

ParameterValue
Offset Adjustment Range|Offset| ≤ 10 - Amplitude/2
Offset Resolution0.01 V

8.6. Phase Characteristics

ParameterValue
Phase Adjustment Range0~359.9°
Phase Resolution0.1°

8.7. TTL/CMOS Output

ParameterValue
Low Level<0.3V
High Level1V~10V
Level Rise/Fall Time≤20ns

9. User Tips

  • For precise waveform analysis, ensure your oscilloscope is properly calibrated and matched to the signal generator's output impedance (50Ω).
  • When using the arbitrary waveform function, experiment with the PC software to create complex custom signals for specific testing needs.
  • Utilize the 100 parameter storage groups to quickly recall frequently used waveform configurations, saving time during repetitive tasks.
  • The dual-channel capability allows for advanced experiments, such as phase-shifted signals or frequency modulation between channels.
  • Always double-check your connections and settings before applying power to external circuits to prevent damage.

10. Warranty and Support

10.1. Warranty

This product comes with a one-year guarantee from the date of receipt. The warranty does not cover products that are physically damaged or operating under abnormal conditions due to misuse or improper installation.

10.2. Technical Support

For technical assistance, troubleshooting, or inquiries regarding your JDS2900 series signal generator, please contact JUNCTEK Official Store customer service. Provide your product model and a detailed description of the issue for efficient support.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.