MESTEK IR03A/IR03B/IR01A/IR01B/IR01C/IR01D/IR02C

Contents

MESTEK Digital Infrared Thermometer User Manual

Models: IR03A, IR03B, IR01A, IR01B, IR01C, IR01D, IR02C

Brand: MESTEK

1. Introduction

Thank you for choosing the MESTEK Digital Infrared Thermometer. This device is designed for non-contact temperature measurement, offering a safe and convenient way to measure surface temperatures across various applications. Featuring a colorful LCD screen, laser targeting, and adjustable emissivity, it provides accurate and quick readings. Please read this manual thoroughly before use to ensure proper operation and safety.

MESTEK Digital Infrared Thermometer

Figure 1: MESTEK Digital Infrared Thermometer

2. Safety Information

2.1 Laser Safety

WARNING: LASER RADIATION. DO NOT STARE INTO BEAM. AVOID DIRECT EYE EXPOSURE.

  • This device uses a Class 2 laser (less than 1mW/630-670nm).
  • Never point the laser directly at people or animals.
  • Avoid aiming the laser at highly reflective surfaces, as reflected beams can also cause eye damage.

2.2 General Safety Precautions

  • This product is not suitable for measuring human body temperature (e.g., forehead, baby).
  • Do not measure through transparent surfaces such as glass or plastic.
  • If the environment temperature changes significantly or suddenly, allow the thermometer to stabilize for at least 30 minutes before use.
  • Do not use the device in explosive gas, vapor, or dusty environments.
  • Keep the device away from water and high humidity.
  • Remove batteries if the device is not used for an extended period.

3. Package Contents

Please check the package contents upon receipt:

  • 1 x MESTEK Digital Infrared Thermometer
  • 1 x User Manual
  • (Note: 1.5V*2 AAA batteries are not included and must be purchased separately.)

4. Setup

4.1 Battery Installation

  1. Locate the battery compartment on the handle of the thermometer.
  2. Open the battery cover.
  3. Insert two 1.5V AAA batteries, ensuring correct polarity (+/-).
  4. Close the battery cover securely.
Battery installation steps

Figure 2: Battery installation and initial measurement

5. Operating Instructions

5.1 Basic Measurement

  1. Point the thermometer at the target object.
  2. Pull and hold the trigger to activate the laser and begin measurement.
  3. The measured temperature will be displayed on the colorful LCD screen.
  4. Release the trigger to hold the reading. The device will automatically shut down after 30 seconds of inactivity.
Colorful LCD display showing temperature and humidity

Figure 3: HD Color Screen Backlit Display

5.2 Display Information

The colorful LCD screen provides the following information:

  • Emissivity (ε): Adjustable from 0.1 to 1.00. Default is 0.95.
  • Room Temperature: Ambient temperature.
  • Room Humidity: Ambient humidity (for IR01C, IR01D, IR02C models).
  • Surface Temperature: The measured temperature of the target object.
  • MAX/MIN Value: Maximum or minimum temperature recorded during continuous measurement.
  • Laser Indication: Icon indicating laser activity.
  • Low Battery Indicator: Alerts when batteries need replacement.
  • Measurement Indication: Icon showing active measurement.
  • High/Low Temperature Alarm: Indication if temperature exceeds set limits.

5.3 Mode Settings (IR03A/B)

To access and adjust settings:

  1. Press and hold the MODE button to enter the maximum temperature setting mode.
  2. Press the MODE button again to enter the minimum temperature setting mode.
  3. Press the MODE button again to enter the emissivity setting mode. Use the up/down arrows to adjust the value.
  4. Press the MODE button again to enter the Celsius/Fahrenheit (°C/°F) switching mode. Use the up/down arrows to switch units.
  5. Long press the MODE button or short press the trigger to exit the setting mode.
Parameter setting interface

Figure 4: Parameter Setting of Thermometer

5.4 Emissivity Adjustment

Emissivity (ε) is crucial for accurate temperature measurement. Different materials have different emissivities. Adjust the emissivity value (0.1-1.00) according to the material being measured for higher accuracy. The default emissivity is 0.95.

Emissivity comparison table for various materials

Figure 5: Emissivity Comparison Table

5.5 High and Low Temperature Alarm

When the measured temperature exceeds the set high or low alarm value, a red warning light on the top of the instrument will illuminate, indicating an out-of-range condition.

5.6 Laser Positioning

  • IR03A/IR03B: Features a single red laser point for targeting.
  • IR01 and IR02 series: Features a 12-point ring laser indicating the temperature-sensitive zone for precise targeting.
Diagram showing 12-point laser targeting and object distance ratio

Figure 6: Object Distance Ratio (D:S) and Laser Targeting

5.7 Object Distance Ratio (D:S)

The D:S ratio for this thermometer is 12:1. This means that at a distance of 12 units from the target, the measurement spot diameter will be 1 unit. For example, if you are 12 inches away from the target, the measurement area will be a 1-inch circle. Maintain an appropriate distance for accurate readings.

5.8 Automatic Shutdown

To conserve battery life, the thermometer will automatically enter sleep mode and shut down after 30 seconds of no operation.

5.9 Correct Measurement Method

When measuring boiling liquids or steam, do not let the smoke or steam contact the temperature sensing area. Keep the measuring angle at approximately 45-60 degrees to the surface.

Video 1: MESTEK Infrared Thermometer Product Demonstration. This video shows the thermometer's features, display, and various measurement applications.

6. Maintenance

  • Cleaning: Use a soft, damp cloth to clean the device casing. Do not use abrasive cleaners or solvents. Ensure the lens is clean and free of dust or debris for accurate readings.
  • Storage: Store the thermometer in a dry, cool place, away from direct sunlight and extreme temperatures.
  • Battery Care: Remove the batteries if the device will not be used for an extended period to prevent leakage and damage.

7. Troubleshooting

  • Inaccurate Readings:
    • Check and adjust the emissivity setting for the material being measured.
    • Ensure the distance-to-spot ratio is appropriate for the target size.
    • Verify the lens is clean.
    • Allow the device to acclimate to the ambient temperature if moved from a significantly different environment.
  • No Display/Device Not Turning On:
    • Check if the batteries are installed correctly and have sufficient charge. Replace with new AAA batteries if necessary.
  • Laser Not Activating:
    • Ensure the device is powered on and the trigger is pressed.
    • Check battery level.
  • Temperature Alarm Not Functioning:
    • Verify that the high/low alarm limits are set correctly in the mode settings.

8. Specifications

FeatureSpecification
Brand NameMESTEK
Model NumberIR03A/IR03B Thermometer (also IR01A, IR01B, IR01C, IR01D, IR02C)
Display TypeDIGITAL
Display Size1.9 Inches & Under
StyleHandheld
UseIndustrial
Power Type1.5V*2 AAA battery (not included)
CertificationCE, RoHS
OriginMainland China
Is Smart DeviceNo
IR03A Temperature Range-50~400°C
IR03B Temperature Range-50~600°C
IR01A Temperature Range-50~380°C
IR01B Temperature Range-50~550°C
IR01C Temperature Range-50~550°C
IR01D Temperature Range-50~800°C
IR02C Temperature Range-50~800°C
Ambient Temperature (IR01C/D, IR02C)-10~60°C
Humidity (IR01C/D, IR02C)0%~100%RH
Emissivity0.1~1.00 adjustable
Distance Spot Ratio (D:S)12:1
Accuracy2°C
Response Spectrum8~14 um
Laser Positioning12 point ring (IR01/IR02 series), 1 point (IR03A/B)
Laser ClassLess than 1mW/630-670nm Level 2
Response TimeLess than 0.5s
Automatic Shutdown30 seconds
Data RetentionYes
Operating Temperature0~40°C
Storage Temperature-10~60°C
Temperature ProbeOnly IR02C
Humidity FunctionOnly IR02C

9. User Tips

  • Emissivity Matters: Always ensure you set the correct emissivity for the material you are measuring to get the most accurate readings. Refer to the emissivity table in this manual.
  • Battery Readiness: Keep spare AAA batteries on hand, as they are not included with the device and are essential for operation.
  • Power Saving: The automatic 30-second shutdown feature is great for battery life. Remember to reactivate the device by pulling the trigger if it enters sleep mode.
  • Environmental Acclimation: If moving the thermometer between areas with significant temperature differences, allow it about 30 minutes to adjust to the new ambient conditions for optimal performance.

10. Warranty and Support

MESTEK products are manufactured to high-quality standards. For any questions, technical support, or warranty claims, please contact the seller or authorized distributor from whom you purchased the product. Please retain your proof of purchase for warranty purposes.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.