1. Introduction
The MESTEK DM100B is a high-accuracy 10000 counts True RMS digital multimeter designed for a wide range of electrical measurements. It features AC/DC voltage, AC/DC current, resistance, capacitance, frequency, temperature, diode, continuity, and Non-Contact Voltage (NCV) detection. Its portable design, large HD digital display with backlight, and flashlight make it convenient for both professional and DIY use.
2. Package Contents
Upon opening the package, please verify that all items are present and undamaged:
- 1 x MESTEK DM100B Digital Multimeter
- 1 x Packing Box
- 1 x Temperature Probe (K-type thermocouple)
- 1 x Set of Test Leads (red and black)
- 1 x User Manual
3. Setup
3.1 Battery Installation
The MESTEK DM100B requires 2 x 1.5V AA batteries (not included). To install the batteries:
- Ensure the multimeter is turned OFF.
- Locate the battery compartment on the back of the device.
- Use a screwdriver to open the battery cover.
- Insert the 2 AA batteries, observing the correct polarity (+/-) as indicated inside the compartment.
- Replace the battery cover and secure it with the screw.
3.2 Connecting Test Leads and Probes
Always ensure test leads are correctly inserted into the appropriate jacks for the desired measurement function. Incorrect insertion will trigger a warning alarm.
- Voltage, Resistance, Capacitance, Frequency, Diode, Continuity, Temperature: Insert the red test lead into the "VΩHz" jack and the black test lead into the "COM" jack.
- Current (mA/uA): Insert the red test lead into the "mA/uA Input socket" and the black test lead into the "COM" jack.
- Current (10A): Insert the red test lead into the "10A Input socket" and the black test lead into the "COM" jack.
- Temperature Measurement: Connect the K-type thermocouple to the designated temperature input terminals (usually marked with TEMP or similar symbols, often sharing the VΩHz and COM jacks, or dedicated ports if available).
4. Operating Instructions
The MESTEK DM100B features an auto-ranging function, simplifying operation. Turn the rotary switch to the desired measurement function.
4.1 Measurement Functions
- AC/DC Voltage (V~ / V-): Measure voltage by selecting the appropriate voltage range on the rotary switch.
- AC/DC Current (A~ / A-): Measure current by selecting the appropriate current range (mA/uA or 10A) and connecting the leads in series with the circuit.
- Resistance (Ω): Measure resistance by selecting the resistance range.
- Capacitance (F): Measure capacitance by selecting the capacitance range.
- Continuity ( ))): Test for continuity. The meter will beep if a continuous path is detected.
- Diode (→|): Test diodes for forward voltage drop.
- Frequency (Hz): Measure the frequency of AC signals.
- Temperature (°C/°F): Use the K-type thermocouple to measure temperature.
- Non-Contact Voltage (NCV): Detect AC voltage without physical contact. The NCV detection area is located at the top of the multimeter. An alarm sound and indicating light will activate when voltage is detected.
- Live Wire Detection: Identify live wires.
4.2 Special Features
- HD Digital Display Screen: Features an analog bar and digital dual display for clear data, easy for novices.
- Data Hold (HOLD): Press the HOLD button to freeze the current reading on the display.
- Backlight: Activates the display backlight for visibility in low-light conditions.
- Flashlight: Provides illumination for the work area.
- Automatic Shutdown: The multimeter will automatically power off after a period of inactivity to save battery life.
- Undervoltage Prompt: Indicates when battery power is low.
- Overload Protection: Built-in smart chip and dual fuses provide overload protection.
- True RMS Measurement: Provides accurate readings for non-sinusoidal AC waveforms.
5. Maintenance
5.1 General Care
- Keep the multimeter clean and dry. Wipe with a soft, damp cloth; do not use abrasive cleaners or solvents.
- Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Remove batteries if the device will not be used for an extended period to prevent leakage.
5.2 Fuse Replacement
The DM100B is equipped with dual fuses for protection. If the multimeter stops functioning correctly, especially in current measurement modes, a fuse may have blown. To replace a fuse:
- Ensure the multimeter is turned OFF and all test leads are disconnected.
- Locate the battery/fuse compartment on the back of the device.
- Carefully open the compartment.
- Identify the blown fuse(s). The DM100B uses standard fuses (e.g., Fused MAX 10A, Fused MAX 600mA).
- Replace the blown fuse(s) with new fuses of the exact same type and rating. Using incorrect fuses can damage the meter or pose a safety hazard.
- Close the compartment securely.
6. Troubleshooting
- No Display/Low Battery: Check battery installation and replace with fresh AA batteries if necessary. The multimeter has an undervoltage prompt.
- "LEAD" Error / Warning Sound: This indicates incorrect insertion of test leads for the selected measurement function. Ensure the test leads are plugged into the correct input jacks as per Section 3.2.
- No Reading / Incorrect Reading:
- Verify the rotary switch is set to the correct measurement function.
- Ensure test leads are making good contact with the circuit or component.
- Check if the fuses are intact (refer to Section 5.2 for fuse replacement).
- Multimeter not responding: Turn the device off and then on again. If the issue persists, replace the batteries.
7. Specifications
| Feature | Specification |
|---|---|
| Model | DM100B |
| DC Voltage | 0-1000V |
| AC Voltage | 0-750V |
| DC Current | 0-10A |
| AC Current | 0-10A |
| Resistance | 0-10MΩ |
| Capacitance | 0-6mF |
| Frequency | 50-1000Hz |
| Temperature | -20℃-1000℃ (-4°F-1832°F) |
| On/Off Beep | Support |
| Range Gear | Auto range |
| Display Count | 10000 COUNTS |
| Automatic Shutdown | Support |
| NCV | Support |
| Wrong Insertion Alarm | Support |
| Data Retention | Have |
| Flashlight Light | Have |
| Dimensions | 185*85*40mm |
| Weight | About 500g |
| Undervoltage Prompt | Support |
| Overload Protection | Support |
| Display Type | Digital Display |
| Operating Mode | Manual Range (Auto Range for most functions) |
| DIY Supplies | Electrical |
| Certification | CE |
| Battery | 2*1.5V AA battery (Not included) |
8. User Tips
- Probe Cleaning: Regularly clean the metal tips of your test probes and the input jacks on the multimeter with a clean, dry cloth to ensure good electrical contact and accurate readings.
- Fuse Access: If you suspect a blown fuse, the case can typically be opened by unscrewing the back panel, often shared with the battery compartment. Always ensure the device is off and leads are disconnected before attempting to open it.
- Portable Design: The multimeter includes a back bracket for support, allowing it to stand upright for easier viewing during measurements. The test probes can also be conveniently stored on the back of the device.
9. Warranty and Support
MESTEK products are manufactured to high-quality standards. For any technical assistance or warranty inquiries, please contact MESTEK Official Store customer support. Keep your purchase receipt as proof of purchase.