AZDOME M300S

Contents

AZDOME M300S Dash Cam User Manual

Model: M300S | Brand: AZDOME

Important Safety Information

Thank you for purchasing this AZDOME dashcam. This instruction manual contains information on how to operate your dashcam. Before using your dashcam, we recommend that you read through this manual to ensure correct usage. To improve the performance of the product, the contents of this manual are subject to change without prior notice.

  • Do not disassemble, repair, or modify the product yourself. Doing so may cause fire, electric shock, or malfunction. For internal inspection and repair, contact the service center.
  • If any foreign matter gets inside the product, detach the power cord immediately. Contact the service center for repair.
  • Do not adjust the product while driving. Doing so may cause an accident. Stop or park your car in a safe place before installing and setting up the product.
  • Do not install the product in a location where the product can interfere with the driver's field of vision. Doing so may cause an accident.
  • Do not use a damaged or modified power cord. Only use the cords provided by the manufacturer. Damaged or modified power cords may cause an explosion, fire, or malfunction.
  • Do not operate the product with wet hands. Doing so may cause electric shock.
  • Do not install the product in an environment with high humidity, or combustible gases or liquids. Doing so may cause an explosion and/or fire.
  • Do not leave the product near infants, children, or pets. There is a risk of them swallowing small components, and/or their saliva may get into the product, causing an explosion due to a short circuit.
  • Do not spray water or wax directly onto the product while cleaning the inside of the car. Doing so may cause fire, electric shock, or malfunction.
  • If smoke or an unusual smell is emitted from the power cord, detach the power cord immediately. Contact the service center or your distributor.
  • Keep the terminals of the power cord clean. Failure to do so may cause excessive heat and fire.
  • Use the correct input voltage. Failure to do so may cause explosion, fire, or malfunction.
  • Plug in the power cord firmly so that it cannot easily be disconnected. Failure to do so may cause fire.
  • Do not cover the product with any material. Doing so may cause external deformation of the product or fire. Use the product and peripherals in a well-ventilated location.

Product Overview

This section provides a visual guide to the components of your AZDOME M300S Dash Cam.

Packing List

Check the box for each of the following items before installing the dash cam:

AZDOME M300S Dash Cam package contents including front camera, rear camera, cables, and accessories.

Image: AZDOME M300S Dash Cam package contents.

  • Front Dash Cam
  • Rear Camera (6M/20ft)
  • Type-C USB Power Cable (3.5m/12ft)
  • Double-sided Tape for Mounting (x1)
  • Electrostatic Sticker (x2)
  • 64GB Micro SD Card (x1)
  • Cable Clips (x5)
  • Pry Tool (x1)
  • User Manual (x1)

Camera Components

The following diagram illustrates the main components of the AZDOME M300S Dash Cam:

Diagram of AZDOME M300S Dash Cam components with numbered labels.

Image: AZDOME M300S Dash Cam component diagram.

  1. Sticker Mount
  2. Front Camera
  3. Micro-SD Card Slot
  4. Type-C Charging Port
  5. WiFi Key (Short Press 3 times to shift between 2.4GHz/5GHz; Press and Hold for 3 seconds to turn on/off WiFi; Press once to shift from “Charge Mode” to “Storage Mode” when connected to USB Cable; Press and Hold for 10 seconds to Format Micro-SD Card and set to default settings)
  6. Rear Camera Slot (AV-IN)
  7. Recording LED Indicator
  8. GPS LED Indicator
  9. Microphone
  10. Reset Button
  11. Speaker
  12. Rear Camera

LED Indicator Status

LEDColorStatus
WiFiWiFi ON
WiFi OFF
RECBlinkingRecording
SolidConnecting to power
Blinking RapidlyUpdating firmware
GPSSolidReceiving GPS signal successfully
Rear CameraSolidRear Camera connected

Specifications

FeatureDescription
ModelM300S
ApertureF=1.8
ColorBlack
LanguageChinese (Simplified), Chinese (Traditional), English, French, German, Italian, Russian, Spanish
MemoryClass 10 or above, high-speed U3 Micro-SD Card (Max External Memory: 128G)
Photo Resolution12M/10M/8M/5M/3M/VGA (Pixels: 800Mega)
Video CodeH.264 (4K)
Video FormatMP4
Video Resolution3840x2160 25P + 1920x1080 25 (Default)
2560x1440 30P + 1920x1080 30
1920x1080 30P + 1920x1080 30
GPS TrackBuilt-in (Internal GPS logger)
WiFiBuilt-in (2.4GHz/5GHz Dual band)
USB PortCharging and Storage
Power Interface5V/2.5A (Corded Electric)
Working Temperature-20°C to 70°C
Storage Temperature-30°C to 85°C
Loop-Cycle RecordingYes
Audio RecordedYes
Maximum Video Frame Rate30 FPS
NightShot FunctionYes
Rear CameraYes
Battery LifeNo battery (Super Capacitor for time memory)
Original PackageYes
Touch ScreenNo
Screen RatioNONE
Memory Card Required Reading SpeedClass 10
View angle170°
Number Of Lenses2
Imaging SensorGC2053
Display SizeNo
Assembly ModeHidden Type
Chipset ManufacturerNOVATEK
Special FeaturesG-Sensor, SD/MMC card, Built-in GPS, Anti Vibration, Wide Dynamic Range, WiFi function, Voice Control, Parking Monitor
CertificationCE, FCC, RoHS, WEEE
InterfaceSD/MMC, USB 2.0

Setup and Installation

Getting Started Tips

  • Setting Date & Time: Please calibrate the date/time based on your location under the TIME ZONE SETTING by going to APP system settings menu.
  • First Time Use: You MUST format the memory card in the camera to prevent any errors and for smooth operation.
  • Power Supply: Make sure to always keep the camera plugged into power, because the camera uses a super capacitor and will not power on without external power.
  • Micro-SD Card: You will need to insert a Micro-SD card before you can start recording. Please insert only a brand name Class-10 or above higher speed Micro-SD card.

Installation Steps

Install the front camera behind the rear view mirror. Install the rear camera at the top of the back windshield. Remove any foreign matter and clean and dry the windshield before installation.

Diagram showing front and rear dash cam installation locations on a car windshield.

Image: Recommended installation positions for front and rear cameras.

  1. Turn off the engine, gently push the Micro-SD card into the slot until it locks into place. (Please use a Class 10 or above high-speed U3 micro-SD card).
  2. Find a suitable place on the windshield where it doesn't obstruct the driver's field of vision. Remove any foreign matter and clean and dry the windshield before installation. Tear off the protective layer of the electrostatic sticker and adhere it to the windshield to prevent marks/glue on your windshield after removing it.
  3. Peel off the protective film from the double-sided tape and attach the front camera to the electrostatic sticker. Adjust the angle of the lens by rotating the body of the front camera.
  4. Peel off the protective film from the double-sided tape and attach the rear camera to the rear windshield. Adjust the angle of the lens by rotating the body of the rear camera. Connect the front camera and the rear camera.
Diagram showing the connection of the rear camera to the front camera and the use of a pry tool for cable routing.

Image: Rear camera connection and cable routing.

  1. Use the pry tool to lift the edges of the rubber window sealing and molding and tuck in the rear camera connection cable.
  2. Plug the cigarette lighter power cable into the cigarette lighter socket and the front camera. Use the pry tool to lift the edges of the windshield trim/molding and tuck in the power cord.
Diagram showing the power cable connection and routing in the car.

Image: Power cable connection and routing.

  1. Turn on the engine. The dashcam will power up and start recording. Video files are stored on the microSD card. Turn off the engine. The dashcam will automatically stop recording and power down.

Operating Instructions

Calibrate Date/Time

The AZDOME M300S has built-in GPS. You need to set the Timezone first in the APP so that the video date/time stamp will be correct.

  1. Search for the AZDOME app in the Google Play Store or Apple App Store and install it on your smartphone.
  2. Manual WiFi Connection Steps:
    1. Open your phone's 'Settings'.
    2. Tap 'WiFi'.
    3. Select 'M300S ***********' (unique ID).
    4. Enter PASSWORD: 12345678.
  3. After installing the AZDOME APP, register for an account with your email address on the registration screen to log in to the app. If you are unable to find the verification code in your email, click the "Skip Login" button in the top right corner to proceed to the next step.
  4. The dash cam model M300S will show when connected successfully. Touch “Check Real-time Video” to go into the preview interface.
  5. Stop recording, and press the settings icon to enter the system setting menu.
  6. Select the “Timezone Setting” and “Date/Time”. The dash camera sets the date and time based on the GMT/UTC value selection when it receives the GPS signal automatically.

General Settings

Photo Size - 12M/10M(Default)/8M/5M/3M/VGA

Here you can choose your desired photo resolution. Higher the resolution, better the pixel resolution for the captured image.

Video Resolution

Allows you to choose the desired video resolution and fps (frames per second). Higher resolution and fps videos result in smoother videos, but also take more storage space.

  • 3840x2160 25P + 1920x1080 25 (Default)
  • 2560x1440 30P + 1920x1080 30
  • 1920x1080 30P + 1920x1080 30

Loop Record - 1min/3mins(Default)/5mins/Off

Allows the dash-cam to continuously record. The dash-cam will automatically delete the oldest files when the memory card gets full, so it can keep recording over and over. Select the desired length of video file for loop recording.

WDR (Wide Dynamic Range) - On(Default)/Off

WDR improves the exposure by combining overexposed and underexposed images into one robust wide range of lighting with higher depth image.

Comparison of dash cam footage with WDR On and WDR Off, showing improved night vision.

Image: Super Night Vision with WDR technology.

Audio Recording - On(Default)/Off

The AZDOME has a built-in microphone to record audio with video. You can choose to record mute video by choosing OFF.

G-Sensor - Off/High/Medium(Default)/Off

The G-Sensor is a 3-axis impact gravitational accelerometer designed to detect physical and gravitational forces. When triggered, the current loop cycle length of the video file will be locked and NOT deleted by the loop cycle function.

Language

This setting allows you to choose your language setting for the camera's firmware.

Picture in Picture

  • Front Camera: APP ONLY shows the front camera image.
  • Rear Camera: APP ONLY shows the rear camera image.
  • Front (Big) + Rear (Small): The front camera image is the primary image, rear camera is the secondary image.
  • Front (Small) + Rear (Big): The front camera image is the secondary image, rear camera is the primary image.

Parking Monitor

This function menu will be shown when connected to a 3-lead hard-wire kit.

Diagram showing 24H Parking Monitoring features: Collision Detection and Time-lapse Recording.

Image: 24H Parking Monitoring features.

  • Off: The dashcam will power off when the car powers off.
  • Time-Lapse Parking Mode: The function is Time-lapse Parking Monitor (1 second = 1 frame per second). When you turn OFF the car's engine and turn the key to the lock position, the camera will STOP loop recording and go into Time-lapse Parking Monitor recording mode automatically. If someone hits your car during this mode, the camera will lock the Time-lapse Parking Monitor recording files and save them in the EMR folder of the Micro SD card. When you start your car again, the camera will automatically STOP Time-Lapse Parking Mode and return to normal video mode.
  • Impact Detection Parking Mode: If set ON, when you turn OFF the car's engine and turn the key to the lock position, the dashcam will also power off, but if someone hits your car, the dashcam will turn on to record for 1 minute and save it in the EMR folder of the Micro SD card, then power off.

Date/Time Format

This feature allows you to select the date format.

Speed Unit - KM/H(Default)/MPH

You can choose the desired speed option stamp to be displayed and recorded on the video stamp based on your selection.

Volume - Low/Medium(Default)/High/Off

This feature allows you to set the volume level for the boot sound volume and prompt volume through the camera's internal built-in speaker.

Boot Sound

This feature allows you to turn ON/OFF the camera button's beep sound.

Voice Switch - On(Default)/Off

Only supports English voice commands: turn on WiFi, take picture, turn off recording, turn off WiFi, open recording, lock the video.

Voice Command

Say a command, but ONLY support English:

  • To turn on WiFi, say "Turn on WiFi"
  • To take a picture, say "Take picture"
  • To stop recording, say "Turn off recording"
  • To turn off WiFi, say "Turn off WiFi"
  • To start recording, say "Open Recording"
  • To lock the current video files to prevent from deleting, say "Lock the video"
Image showing a person using voice commands with the dash cam.

Image: Smart Voice Control in action.

Frequency - 50HZ/60HZ(Default)

Choose the frequency according to your power supply specification used in your country based on your geographical location.

Mirror Rear Camera

This feature works only on the rear camera image.

  • On: The image of the rear camera is the same as in the rear mirror (what's on the left in reality is on the right of the dash cam screen).
  • Off: The rear camera image is as you see (what's on the left in reality is on the left of the dash cam screen).

Vertical Flip Rear Camera

This feature will allow you to flip your video 180 degrees so you can still have a correct side of image when the camera is mounted upside-down.

Voice Prompts

VoiceDescription
Emergency VideoThe current file will be saved and locked in EMR folder of Micro-SD card
WiFi ONWiFi is on
WiFi OFFWiFi is off
Storage Card ExceptionThe Micro-SD card meets problems
Storage ModeWhen connected to USB cable (not included), dash cam becomes a storage disk that can read files
Charge ModeWhen connected to USB cable (not included), dash cam is charging
Sound as "Click"Taking photo
Format SuccessfullyFormat memory card successfully
Format FailedFormat memory card failed
Rear Camera ConnectedRear camera connected to dashcam successfully

WiFi & App Control

The AZDOME M300S has built-in 2.4G and 5GHz Dual-frequency WiFi module, with 5G as the default value. If your phone cannot find the M300S WiFi, it means your phone only supports the 2.4GHz band. Short press the WiFi button 3 times in a row to shift to 2.4GHz.

To connect and use the AZDOME APP:

  1. Search for the AZDOME app in the Google Play Store or Apple App Store and install it on your smartphone.
  2. "Pair" your smartphone with the AZDOME dash cam via Wi-Fi Direct: Power on the engine, the dash cam will power on and WiFi will turn ON automatically. Choose your AZDOME dashcam from the phone WiFi network list. The dashcam's default SSID begins with its model number (e.g., M300S-******, password 12345678).
  3. Go to the dash cam preview interface. Press the “Device Album” to get Photo, Video, Emergency files.
  4. You can select files to download to your smartphone. These downloaded files can be found in the APP's original interface menu named "Local Video".
  5. You can playback the video or edit the video files.

Video: AZDOME M300S Dash Cam features overview, including 4K+1080P resolution, night vision, GPS tracking, mini size, voice control, and Wi-Fi & App control.

Maintenance

Managing Videos

Managing videos by Micro-SD card reader:

  1. Remove the Micro SD card from the camera and insert it directly into your laptop if you have a Micro SD Card slot (otherwise use a Micro SD Card reader).
  2. You should be able to see drive "D" or "E" or other name depending on the pre-installed hard drives. Once you find the added flash drive, double click in it, then you will see the file folders: Movie / EMR / Photo.
    • Movie: The loop recording video files that can be overwritten.
    • EMR: The video file will be locked so it will NOT be deleted by loop recording function.
    • Photo: The photos.
  3. Simply double click on the video to play them.
Screenshot of AZDOME GPS Player and AZDOME APP showing GPS tracking on Google Maps.

Image: GPS Tracking on Google Map via AZDOME Player and APP.

AZDOME GPS Player

  1. Please go to our official website www.azdomevip.com/support to download the AZDOME Player (for Windows or macOS).
  2. Install the AZDOME Player on your computer. (Note: Please close or ignore the prompt of the anti-virus software, it will not bring any security impact to your computer.)
  3. Take off the memory card from the dashcam and insert it into your computer.
  4. There are two ways to play video:
    • Click File-Open icon to choose the folder you want to play, click to start play. (Note that you can ONLY select one folder to play and see no video files).
    • Select from “My Computer” and find the memory card disk, choose the video file you want to play, you can drag and drop the file directly to the player. You can get the GPS information on the player.

Formatting the Micro-SD Card

There are two ways to format the Micro-SD card:

  1. Press and hold the WiFi button for 10 seconds to format and default settings. You will hear a "di" sound when formatted successfully.
  2. Connect to the AZDOME APP and use the function menu named "Format" to do so.

Firmware Update

  1. Download the firmware file from www.azdomevip.com/pages/support.
  2. Copy the firmware file named “FW96670.bin” to the Micro SD card and insert the Micro-SD card into the dash cam.
  3. Connect to power, then the red light will flash rapidly. It will take 30-40 seconds to update. The dash cam will power on automatically and say “WiFi is ON” when the update is successful.
  4. Press and hold the WiFi button for 10 seconds to format the Micro SD Card in the dash cam, otherwise the dash-cam will update again when next power on.

Troubleshooting and FAQ

  • Q: I can't get live video on AZDOME APP, what should I do?
    A: If you can't get live-video on the APP, please turn off cellular data for the AZDOME APP. For iPhone and Google phone (Android 12) for example, go to Settings > Privacy > Location Services > AZDOME and set to "While Using the App" and ensure "Local Network" is enabled.
  • Q: Is the rear camera external and waterproof?
    A: Yes, the rear camera is an external component. While not explicitly stated as waterproof in all specifications, external rear cameras are typically designed to be weather-resistant for outdoor use.
  • Q: What is meant by a hardwire kit?
    A: A hardwire kit is an accessory (not included in the standard package) that connects the dash cam directly to your car's fuse box. This allows the dash cam to receive continuous power even when the car is turned off, enabling features like 24-hour parking monitoring (collision detection and time-lapse recording).
  • Q: How does the product work, battery or charge?
    A: The AZDOME M300S Dash Cam does not have an internal battery for operation. It is powered by a corded electric connection (5V/2.5A) via the car's cigarette lighter socket. It uses a super capacitor to save time and date settings.
  • Q: Does this model have motion detection function?
    A: Yes, it has a "Parking Monitor" feature which includes collision detection (via G-Sensor) and time-lapse recording. These functions are active when the dash cam is connected via a hardwire kit.

User Tips

  • For optimal performance, always use a high-quality Class 10, U3 Micro-SD card.
  • Regularly format your Micro-SD card (at least once a month) to ensure smooth recording and prevent data corruption.
  • If you experience issues with WiFi connectivity, try switching between 2.4GHz and 5GHz bands by pressing the WiFi button three times.
  • Utilize the voice control features for hands-free operation, enhancing safety while driving.
  • Consider installing a hardwire kit to enable the full 24-hour parking monitoring features for continuous vehicle protection.

Warranty and Support

The AZDOME dash cam comes with a full 12 months warranty. If you have any questions regarding your product, please do not hesitate to contact us via email at service@azdomevip.com. Queries are typically answered within 12-24 hours.

AZDOME is firmly committed to always improving our products, services, and user experience. If you have any thoughts on how we can do even better, we welcome your constructive feedback and suggestions.

Manufacturer Address: Dongguan Lingdu Electronic Technology Co., Ltd, 1 Longcheng Qingxi Town, Dongguan City, Guangdong Province, China.

Regulatory Notice

CE Compliance

This product complies with the radio interface requirements of the European Community. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

FCC Compliance

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

© 2024 AZDOME. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.