1. Introduction
Thank you for choosing the Rocket TS160V2 Pro 160A Sensored Brushless ESC and its dedicated Programmer Card. This high-performance speed controller is designed for 1/10 and 1/12 scale RC cars, offering precise control for sensored brushless motors. The included programmer card allows for easy adjustment of various ESC parameters.
To ensure optimal performance, longevity, and safety, please read this manual thoroughly before operating your ESC and programmer card. Keep this manual for future reference.
2. Safety Warnings
Failure to follow these warnings may result in malfunction, electrical issues, overheating, fire, and could lead to injury or property damage.
- Never leave the ESC or connected batteries unattended during operation or charging.
- Ensure all connections are secure and correct polarity is observed. Incorrect wiring can cause severe damage.
- Do not operate the ESC or programmer card if any components are damaged or wet.
- Avoid operating the ESC in extremely hot or cold environments, or in direct sunlight.
- Always use batteries that are compatible with the ESC's specifications (2-3S LiPo / 5-10S NiMh).
- Keep the ESC and programmer card away from flammable and explosive materials.
- Do not attempt to disassemble or modify the ESC or programmer card.
- Ensure proper ventilation for the ESC during operation to prevent overheating.
3. Product Features
- Efficient Heat Dissipating System: Features a high-performing removable cooling fan and an aluminum casing with a reticular heat sink for maximum cooling.
- Built-in Electronic Switch: Saves space and simplifies wiring with a waterproof, dust-proof, and shock-resistant design.
- Built-in Super BEC: Provides 3A output at 6V/7.2V, suitable for various high-voltage servos.
- Separate Programming Connector: Easy to use for adjusting ESC parameters.
- Adjustable Throttle & Brake: Guarantees precise and accurate throttle and brake control for competitive use.
- Removable Aluminum Fan Housing: Lightweight, provides safety protection, and is easy to install.
- Sensored Brushless ESC: Designed for sized 540 sensored brushless motors.
4. Specifications
4.1. ESC Specifications
| Parameter | Value |
|---|---|
| Cont. Current | 160A |
| Burst Current | 760A |
| Forward / Brake / Reverse | YES (Preset - Forward/Brake) |
| Voltage Input | 4.8V-9.9V (2-3S LiPo / 5-10S NiMh) |
| Suitable Car | 1:10 / 1:12 Car |
| BEC Output | 6V/3A |
| Motor Limit | Over 4.5 Turns |
| Motor Type | 540 sensored size brushless motor |
| Multi Protection System | Yes |
| Dimensions (LxWxH) | 38.2 x 30.6 x 32mm |
| Net Weight (without cable) | 55g |
| Weight (with cable) | 108g |
4.2. Programmer Card Specifications
| Parameter | Value |
|---|---|
| Item Number | TS160V2 ESC special |
| Dimensions (LxWxH) | 90 x 55 x 10mm |
| Weight | 75g |
5. Package Contents
The package includes the following items:
- 1 x Rocket TS160V2 Pro 160A ESC
- 1 x Line Cable (1m)
- 1 x Capacitor
- 1 x LCD Program Card (if selected SKU)
6. Setup and Installation
6.1. Component Overview
6.2. Physical Installation and Heat Dissipation
The ESC features a detachable design for easy cleaning and maintenance. The aluminum fan cover is lightweight and provides safety protection for the fan. The efficient heat dissipating system combines a high-performing removable cooling fan with an aluminum casing and reticular heat sink to ensure maximum cooling.
6.3. Wiring Connections
Ensure all connections are firm and correctly oriented. The ESC features dedicated power connections (A, B, C, +, -) and a separate programming connector.
6.4. Radio & ESC Setup
Follow these steps to set up your radio and ESC. This process involves calibrating the throttle endpoints of the ESC with your transmitter.
Transmitter Settings:
- Throttle Travel Maximum: 100%
- Brake Travel Maximum: 100%
- Throttle Exponential Start: 0%
- Throttle Neutral Trim Centre: 0
- Throttle Reverse: Futaba, KO, Sanwa (Adjust as per your radio's requirements)
Initial set-up of the throttle end-points of the ESC:
- Connect the ESC power wires to the battery.
- Switch on the radio.
- Press and hold the on/off button, release until the red LED light is off.
- Press the on/off button and hear a sound of beep when the throttle is at the center point.
- Hold and full throttle, press the on/off button, release when you hear two sounds of beeps.
- Hold and full brake, press the on/off button, release when you hear three sounds of beeps.
Now you have successfully bound the radio and ESC, and it is ready for immediate use.
- Bind your receiver and transmitter first if your radio requires you to do so.
- Turn on ESC and listen for 1 beep.
- After you hear the 2 beeps, apply full throttle and listen for another 2 beeps.
- Once you hear the 3 beeps, release the throttle to neutral position.
- A beep will then sound, signifying that the ESC endpoints have been successfully set.
Note: If you do not hear the beeping sound as described above, try reversing the throttle reverse setting in the transmitter.
7. Operating the Programmer Card
The dedicated LCD Program Card allows for easy and precise adjustment of various ESC parameters. This section outlines how to connect and use the programmer card.
7.1. Connecting the Programmer Card
Connect the programmer card to the ESC's separate programming connector using the provided cable. Ensure the connection is secure.
7.2. Adjusting ESC Settings
Once connected, the programmer card's LCD screen will display the current ESC parameters. Use the "SELECT", "UP/DOWN", and "ENTER" buttons on the programmer card to navigate through the menus and adjust settings. Refer to the table below for common adjustable parameters and their functions.
While the image above shows a detailed parameter table, the programmer card itself will provide English labels for each setting. Common adjustable parameters typically include:
- Running Mode: Forward/Brake, Forward/Brake/Reverse, Forward/Reverse
- Cut Off Voltage: Low, Middle, High (for battery protection)
- ESC Overheat Protection: Temperature threshold
- Motor Overheat Protection: Temperature threshold
- Throttle Neutral Range: Adjustable percentage
- BEC Output Voltage: 6V, 7V, 7.2V
- Motor Direction: CW, CCW
- Motor Link: Normal, A SWAP C
- Remote Off: Enabled/Disabled
- Punch (Throttle Acceleration): Level 1-30 (Adjustable)
- PWM Frequency: 2000-32000Hz (Adjustable)
- Drag Brake: 0-30% (Adjustable)
- Brake Force: 0-100% (Adjustable)
- Boost Timing: 0-60 degrees (Adjustable)
- Turbo Timing: 0-60 degrees (Adjustable)
- Turbo Delay: 0-1.00s (Adjustable)
- Turbo Up/Down Rate: Adjustable
Navigate through these options using the programmer card's buttons and select your desired values. Always save your settings before disconnecting the programmer card.
8. Maintenance
Regular maintenance ensures the longevity and optimal performance of your Rocket TS160V2 Pro ESC.
- Cleaning: The ESC features a detachable design, making it easy to clean. Periodically remove the fan housing and fan to clean any dust or debris that may accumulate, especially in the heat sink fins. Use a soft brush or compressed air.
- Inspection: Regularly inspect all wires and connectors for signs of wear, damage, or corrosion. Ensure all screws, especially those holding the fan, are secure.
- Storage: When not in use, store the ESC and programmer card in a dry, cool place, away from direct sunlight and extreme temperatures.
9. Troubleshooting
If you encounter issues with your ESC, consider the following common troubleshooting steps:
- No Power/No Response:
- Check battery connections and ensure the battery is charged.
- Verify the ESC's power switch is in the ON position.
- Inspect all wiring for loose connections or damage.
- Motor Not Responding/Erratic Behavior:
- Ensure the radio and ESC are properly bound and calibrated (refer to Section 6.4).
- Check motor connections (A, B, C phases) for correct polarity and secure fit.
- Verify that the motor type (sensored brushless) is compatible with the ESC.
- Check for any obstructions in the motor or drivetrain.
- Overheating:
- Ensure the cooling fan is operating correctly and is free from obstructions.
- Check for proper ventilation in your RC vehicle.
- Verify that the motor and gearing are appropriate for your setup and not causing excessive load.
- Consider reducing aggressive settings via the programmer card if consistent overheating occurs.
- Programmer Card Not Connecting/Displaying:
- Ensure the programmer card is securely connected to the ESC's programming port.
- Check the cable for damage.
- Ensure the ESC is powered on.
If problems persist, consult with your retailer or contact customer support.
10. Firmware Update
Firmware updates may be released periodically to improve performance or add new features. Please refer to the manufacturer's official website or support channels for the latest firmware and detailed update instructions specific to the Rocket TS160V2 Pro ESC and Programmer Card.
11. User Tips
While no specific user tips were gathered from reviews or Q&A for this product, general best practices for RC ESCs include:
- Always start with default or conservative settings when first using the ESC, then adjust parameters gradually to fine-tune performance.
- Monitor ESC and motor temperatures during initial runs to prevent overheating.
- Keep your RC vehicle's drivetrain clean and well-lubricated to reduce strain on the ESC and motor.
- Ensure your battery is in good condition and properly charged for consistent performance.
12. Warranty and Service
This product is guaranteed to be free of manufacturing and assembly defects for a period of one year from the time of purchase. The warranty applies only to material or operational defects present at the time of purchase. During this period, defective products will be repaired or replaced free of service charge.
This warranty does not cover damage resulting from misuse, modification, or failure to observe the procedures outlined in this manual. For warranty service, please contact your dealer or the point of purchase.
Note:
- The warranty service is typically valid in the country of purchase.
- For overseas warranty service, please contact your dealer. Due to shipping costs and customs procedures, direct overseas service from the manufacturer may not be available.
- For any questions not covered in this manual, please contact customer support.
13. Conformity Declaration
The Rocket TS160V2 Pro ESC and Programmer Card comply with all relevant and mandatory CE directives and FCC Part 15 Subpart B.