1. Introduction
The MYT-925 CB Radio is a compact and versatile 27MHz mini transceiver designed for reliable wireless communication. Featuring 40 channels, switchable AM/FM modes, and RF gain control, it is suitable for various mobile applications. This manual will guide you through the proper installation, operation, and maintenance of your device to ensure optimal performance.
2. Features
- High power output: 8W (High/Low power selective)
- Frequency range: 25.615-30.105MHz (3 groups selectable)
- 40 storage channels
- AM and FM mode switchable
- AM and FM mode squelch level adjustment
- RF gain control
- Keypad lock function
- Scan function
- Frequency is fixed and unprogrammable
3. Package Contents
Please check the package for the following items:
- 1x MYT-925 Mobile Radio Unit
- 1x Microphone
- 1x Mounting Bracket
- 1x Power Cable
- 1x Screw Set

4. Product Overview
Familiarize yourself with the main unit and microphone controls.


Controls:
- LCD Screen: Displays channel, frequency, and other operational information.
- SQ (Squelch) Button: Adjusts the squelch level to filter out weak signals and noise.
- A/F (AM/FM) Button: Toggles between Amplitude Modulation (AM) and Frequency Modulation (FM) modes.
- RFG (RF Gain) Button: Controls the sensitivity of the receiver to incoming signals.
- EMG (Emergency) Button: Activates emergency channel (if configured).
- Channel Knob: Used to select desired channels.
- Microphone: For transmitting voice. Includes a coiled cord and an RJ45 connector.
5. Setup
Follow these steps to set up your MYT-925 CB Radio:
- Mounting the Radio:
Use the provided mounting bracket and screw set to securely install the radio in your desired location (e.g., vehicle dashboard). Ensure the location allows for proper ventilation and easy access to controls.

Figure 5.1: Mounting bracket. - Power Connection:
Connect the red wire of the power cable to the positive (+) terminal of your vehicle's 13.2V power source, and the black wire to the negative (-) terminal or chassis ground. Ensure a secure connection to prevent power fluctuations.

Figure 5.2: Power cable. - Antenna Connection:
Connect a suitable CB antenna (UHF, SO-239 type) to the antenna connector on the rear of the radio. Ensure the antenna is properly tuned for 27MHz operation for optimal performance and to prevent damage to the transceiver.

Figure 5.3: Antenna connector on the rear of the unit. - Microphone Connection:
Plug the microphone's RJ45 connector into the corresponding port on the front of the radio.

Figure 5.4: Microphone connection.
6. Operating Instructions
- Power On/Off:
Turn the volume knob clockwise to power on the radio. Turn it counter-clockwise until it clicks to power off.
- Channel Selection:
Rotate the Channel Knob to select one of the 40 available channels. The selected channel will be displayed on the LCD screen.
- AM/FM Mode Switching:
Press the A/F button to switch between AM (Amplitude Modulation) and FM (Frequency Modulation) modes. The current mode will be indicated on the display.
- Squelch Level Adjustment:
Press the SQ button. Use the Channel Knob to adjust the squelch level. A higher squelch level will filter out more background noise but may also block weaker signals. Adjust until background noise is eliminated without losing desired signals.
- RF Gain Control:
Press the RFG button. Use the Channel Knob to adjust the RF Gain. This controls the sensitivity of the receiver. Lowering RF Gain can help reduce interference from strong nearby signals.
- Transmitting:
To transmit, press and hold the PTT (Push-To-Talk) button on the microphone. Speak clearly into the microphone. Release the PTT button to return to receive mode.
- Keypad Lock:
The radio features a keypad lock to prevent accidental changes to settings. Refer to the on-screen prompts or a combination of buttons (not specified in provided data, assume standard functionality) to activate/deactivate.
- Scan Function:
Activate the scan function to automatically cycle through active channels. Press the Scan button (if available, or a combination of buttons) to start/stop scanning.
- Emergency Channel (EMG):
Press the EMG button to quickly access a pre-programmed emergency channel. This is typically used for urgent communications.
Note: The frequency of this device is fixed and unprogrammable by the user.
7. Maintenance
- Cleaning: Use a soft, dry cloth to clean the radio's exterior. Do not use harsh chemicals or solvents.
- Storage: When not in use for extended periods, store the radio in a cool, dry place away from direct sunlight and extreme temperatures.
- Antenna Care: Regularly inspect your antenna and its connections for any signs of wear or damage. A damaged antenna can affect performance and potentially harm the radio.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Loose power connection, blown fuse, vehicle battery issue. | Check power cable connections. Inspect the fuse in the power line. Verify vehicle battery voltage. |
| No reception or poor reception | Antenna not connected, damaged antenna, high squelch level, low RF gain. | Ensure antenna is securely connected. Check antenna for damage. Adjust squelch level down. Increase RF gain. |
| Cannot transmit | Microphone not connected, PTT button faulty, antenna issue. | Check microphone connection. Ensure PTT button is fully pressed. Verify antenna connection and condition. |
| Excessive background noise | Low squelch level, strong interference. | Increase squelch level. Try adjusting RF gain. Move away from sources of electrical interference. |
9. Specifications
General Specifications
| Modulation mode | AM/FM |
| Frequency range | 25.615-30.105MHz |
| Frequency tolerance | ±5.0ppm |
| Input voltage | 13.2V |
| Dimensions (mm) | 109*104*25 |
| Weight (g) | 421 |
| Frequency control | PLL Synthesizer |
| Operating Temperature Range | -25℃ ~ +50℃ |
| Current Drain (Transmit) | 2A MAX |
| Current Drain (Receive Squelched) | 0.3A |
| Current Drain (VOL Max) | 0.8A |
| Antenna Connector | UHF, SO-239 |
Transmitter Specifications
| Power output | 8 Watts FM/AM |
| Transmission interference | Inferior to 4nW (-54dBm) |
| Frequency Response | 300-3000Hz |
| Modulated signal distortion | Inferior to 5% |
| Output Impedance | 50 ohms |
Receiver Specifications
| Sensitivity | Less than 1uV or 10dB (S+N)/N |
| Image Rejection | 70dB |
| Adjacent Channel Rejection | 60dB |
| IF Frequencies (1st) | 10.695MHz |
| IF Frequencies (2nd) | 455Khz |
| Audio Output Power | 1 watts |
| Squelch | Less than 1uV |
| Frequency Response | 300-3000Hz |
Frequency Table

10. User Tips
- Antenna Tuning: For optimal performance and to prevent damage to your radio, ensure your CB antenna is properly tuned (low SWR) for the 27MHz band. Consult an expert if you are unsure how to tune your antenna.
- Power Source: Always connect the radio directly to your vehicle's battery or a dedicated fused power source to avoid interference and ensure stable operation.
- Microphone Handling: Speak clearly and at a consistent distance from the microphone for best audio quality during transmission.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.