1. Introduction
The RHUNDO RS-21S is a versatile 3-way cigarette lighter socket splitter designed to expand your vehicle's power outlets. It features three extended 12V DC power outlets and dual USB ports, each controllable via individual touch sensor power switches. The device also includes a master power switch, multi-mode display for battery voltage, USB output current, timing, and temperature (with optional external sensor), along with advanced features like Power-on Delay, Automatic Power-off, and Battery Discharge Prevention. This manual provides detailed instructions for installation, operation, and maintenance to ensure safe and efficient use of your device.
2. Safety Information
- Ensure the device is compatible with your vehicle's 12V-24V DC power system.
- Do not exceed the maximum load capacity of 127W total (90W per single socket, 110W total for 3 sockets, 17W for USB ports).
- Avoid exposing the device to extreme temperatures, direct sunlight for prolonged periods, or moisture.
- Keep out of reach of children.
- Do not attempt to disassemble or modify the device.
- Ensure proper ventilation around the device during operation.
- Always turn off the device or unplug it when not in use or when leaving the vehicle for extended periods, especially if your vehicle has an "always on" cigarette lighter socket.
3. Package Contents
Please check the box for the following items:
- Main Unit (3-way splitter with USB ports)
- Control Unit (with touch sensor switches and display)
- Power Plug (cigarette lighter plug)
- Double-sided Adhesive
- Wire Clip
- Spare Fuse
- User Manual (this document)

4. Product Overview
The RS-21S consists of a main unit and a separate control unit, connected by a cable. This split design allows for flexible placement within your vehicle.

Main Unit
The main unit houses the three cigarette lighter sockets and two USB charging ports. It connects to your vehicle's 12V DC power outlet.

Control Unit
The control unit features a digital display and four touch sensor power switches to individually control the three outlets and the USB ports. It also includes a master power switch for overall device control and function configuration.

Wireless Temperature Sensor (Optional RTW-15)
The RTW-15 Wireless Temperature Sensor Module (sold separately) can be paired with the RS-21S to display real-time temperature readings on the control unit's screen. It connects via a small USB receiver that plugs into one of the main unit's USB ports.

5. Setup
5.1 Installation of Main and Control Units
- Connect the Power Plug: Insert the power plug into your vehicle's cigarette lighter socket.
- Position the Main Unit: Place the main unit in a discreet location where it will not interfere with driving, such as under a seat or in a console.
- Position the Control Unit: Mount the control unit within arm's reach and clear view, using the provided double-sided adhesive. Ensure the cable connecting the main and control units is routed safely and secured with the included wire clips.


5.2 Wireless Temperature Sensor Pairing (RTW-15, if applicable)
To pair the optional RTW-15 Wireless Temperature Sensor Module:
- Ensure the RS-21S control unit is powered on and the USB port is active.
- Plug the RTW-15 USB receiver into one of the USB ports on the main unit.
- Press and hold the button on the RTW-15 USB receiver while inserting it into the USB port.
- Press and hold the button on the RTW-15 Wireless Temperature Sensor Module until pairing is complete. The display on the control unit will show temperature readings once paired.
Note: The battery (CR2032) for the RTW-15 is removed for international shipping purposes. Customers need to buy their own battery and install them prior to use.
6. Operating Instructions
6.1 Master Power Switch
The mechanical master power switch on the control unit serves multiple functions:
- Turn on or off the entire device.
- Switch between the display modes.
- Adjust the brightness for the backlighting of the touch switches.
- Clear the timer values.
- Restore from overload protection.
- Configure functions Fn.1 to Fn.6.

6.2 Touch Sensor Power Switches
The four capacitive touch sensor switches allow you to turn on or off power to each of the three extended outlets and the dual USB ports independently. These switches have memory, retaining their ON/OFF state even after the device is shut off or disconnected from power.

Sequential Power-on: When the device is powered on, the touch switches and their corresponding outlets/USB ports activate sequentially. This reduces current surge that could occur if all attached appliances turned on simultaneously.

6.3 Multi-Mode Display
Briefly pressing the master power switch allows you to cycle through the display modes:
- Battery Voltage: Displays the vehicle's battery voltage.
- USB Output: Displays the output current of the two USB ports.
- Temperature: Displays temperature (requires external temperature sensor cable or wireless sensor).
- Timer: Displays the elapsed time since the unit powered on.

6.4 Power-on Delay Timer (Fn.1)
This feature protects attached appliances from voltage surges during engine startup. You can set a delay time from 1 to 30 seconds. The device will not switch on until the set time has elapsed after being connected to the power supply.

6.5 Automatic Power-off & Battery Discharge Prevention (Fn.2 & Fn.3)
Designed for vehicles with "always on" cigarette lighter sockets, this feature prevents battery drain. You can set the device to automatically power off after a specified time (1-120 minutes) once the engine shuts off (Fn.2). Additionally, you can set a threshold voltage (11.0V-14.0V) for Fn.2 to activate, ensuring the device cuts off if the battery voltage drops too low (Fn.3).


6.6 Temperature Display (Fn.4)
With an external temperature sensor (wired or wireless) connected, you can toggle the temperature display function on or off, and choose between Centigrade (°C) and Fahrenheit (°F) units using Fn.4.

External Temperature Sensor Cable: The optional external temperature sensor cable uses a high-precision, high-sensitivity 18B20 temp sensor chip with an accuracy of ±0.5°C. It features a stainless steel casing sealed with heat-conducting resin for reliability and water resistance, suitable for outdoor applications. Note: This cable is not a standard accessory and must be purchased separately.

6.7 Voltage Display Offset (Fn.5)
This function allows you to manually calibrate the displayed battery voltage readings for improved accuracy.
6.8 Low Voltage Alert Value (Fn.6)
Set values for a low battery voltage alert to be displayed on the control unit.
6.9 Overload Protection
The device features circuit-based overload protection. Once the total output reaches 90W, the power to the 3 outlets and USB ports will be cut off, and the flashing text "HGH" will be displayed, indicating an overload. The overload protection circuit uses a constantan wire as a sampling resistor for accurate and reliable protection. A conventional glass-tube fuse is also integrated into the power plug for additional safety.

6.10 Function Configuration (Fn.1 - Fn.6)
The master power switch is used to access and configure functions Fn.1 through Fn.6. When a setting is completed, "SET" will be displayed.

7. User Tips
- The device is designed to work with both 12V and 24V vehicle electrical systems.
- Utilize the auto power-off feature to prevent your car battery from draining, especially if your vehicle's cigarette lighter socket remains powered when the ignition is off.
- For optimal temperature readings, ensure the wireless temperature sensor (RTW-15) is placed in an area with good signal reception and away from direct heat sources or air vents.
8. Troubleshooting
- Device not powering on: Check the connection to the cigarette lighter socket. Ensure the vehicle's ignition is on (if applicable). Verify the master power switch is in the ON position. Check the fuse in the power plug and replace if blown.
- No power from an outlet/USB port: Ensure the corresponding touch sensor switch is activated (blue light). Check for overload (display shows "HGH").
- Temperature not displayed: Ensure the external temperature sensor (wired or wireless) is properly connected or paired. Verify Fn.4 is set to ON.
- Inaccurate voltage reading: Use Fn.5 to calibrate the voltage display offset if you suspect inaccuracies.
- Device shuts off unexpectedly: Check your Fn.2 (Auto Power-off) and Fn.3 (Threshold Voltage) settings. The device might be shutting off due to these settings or an overload.
9. Specifications
| Feature | Specification |
|---|---|
| Input Voltage | DC 10-28V |
| Max. Output for USB Ports | DC5V-3.4A (Total) / 2.4A (Single) |
| Load Capacity for Outlets | Single 7.5A (~90W) / Total 9A (~110W) |
| Total Load Capacity | 127W |
| Display Modes | Battery Voltage / USB Output / Timer / Temperature (External temp sensor needed for temp display) |
| Ways to Switch Between Display Modes | Manually / Automatically |
| Power-on Delay Timer | 1-30 Seconds |
| Auto Power-off Delay Timer | 1-120 Minutes |
| Threshold Voltage Setting | 11.0V-14.0V (with each step of 0.1V) |
| Temperature Display Range | -58°F ~ 248°F (-50°C ~ 120°C) |
| Voltage Display Offset | -0.5V-0.5V |
| Overload Warning for Outlets | >90W ("HGH" displayed) |
| Overload Warning for USB Ports | >3.4A (Output Amps & "HGH" alternately displayed) |
| Length of Main Power Cord | 2.95ft (85cm) |
| Length of Cable for Control | 3.94ft (120cm) |
Wireless Temperature Sensor Module RTW-15 (Optional)
| Feature | Specification |
|---|---|
| Wireless Range | 10m (33ft) |
| Operating Temp | -20°C ~ 60°C (-4°F ~ 140°F) |
| Temp Measurement Precision | ±0.5°C (±0.9°F) |
| Temp Display Resolution | 0.1°C (0.2°F) |


10. Warranty and Support
This product is covered by a standard manufacturer's warranty. For warranty claims, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Please retain your proof of purchase for warranty validation.