Introduction
Thank you for purchasing the Cherub WMT-578RC Tuner Metronome. This device is designed to provide accurate tuning and metronome functions for various wind instruments, including flutes and saxophones. Please read this manual carefully to ensure proper use and to get the most out of your new instrument accessory.

Image: Cherub WMT-578RC Tuner Metronome in black and red, showing the front display and buttons.
Package Contents
Please check the package for the following items:
- 1 x Cherub WMT-578RC Tuner Metronome (Color: Black or Red)
- 1 x User Manual
Setup
1. Battery Installation
The WMT-578RC requires two AAA batteries (not included) for operation.
- Locate the battery compartment on the back of the device.
- Slide open the battery compartment cover.
- Insert two AAA batteries, ensuring correct polarity (+ and -).
- Close the battery compartment cover securely.

Image: Back view of the device, highlighting the battery compartment and integrated kickstand.
2. Powering On/Off
Press and hold the power button (usually marked with a circle and vertical line) to turn the device on or off.
3. Using the Kickstand
The device features an integrated kickstand on the back for convenient tabletop use. Fold it out to prop up the tuner metronome for better viewing.
Operating Instructions
The WMT-578RC has three main modes: Tuner, Metronome, and Tone Generator. Use the "M/T" button to cycle through these modes.

Image: Visual representation of the Tuner, Metronome, and Tone Generator modes on the device's display.
1. Tuner Mode
In Tuner mode, the device helps you accurately tune your instrument.
- Selecting Tuning Mode: Press the "M/T" button until "Tuner" is displayed. You can select between Chromatic and specific Wind Instrument modes (C, F, B♭, E♭). Use the arrow buttons to change the key.
- A4 Calibration: The default A4 reference pitch is 440Hz. To adjust this, use the arrow buttons to set the desired frequency between 430Hz and 450Hz.
- Detection Method: The tuner can detect pitch via its built-in microphone (MIC) or through a line-in connection. Ensure your instrument is close to the microphone or connected via line-in.
- Reading the Display:
- The large LCD display shows the detected note, cent deviation, and Hz frequency.
- The needle-like indicator moves left or right to show if the pitch is flat or sharp.
- LED indicators (red for flat/sharp, green for in-tune) provide quick visual feedback.
- Tuning Process: Play a single note on your instrument. Adjust your instrument until the display shows the correct note, the needle is centered, and the green LED lights up.
2. Metronome Mode
Use Metronome mode to practice with a steady beat.
- Activating Metronome: Press the "M/T" button until "Metronome" is displayed.
- Adjusting Tempo (BPM): Use the Up (▲) and Down (▼) arrow buttons to set the desired tempo from 30 to 250 beats per minute (bpm).
- Adjusting Beat: Press the note symbol button to cycle through beat patterns (e.g., 0, 1, 2, 3, 4, 5, 6, 7, 8, 9). Use the arrow buttons to select the desired beat.
- Start/Stop: Press the power button to start or stop the metronome sound.
- Volume: Adjust the volume using the volume control dial on the side of the device.
3. Tone Generator Mode
The Tone Generator produces reference tones for ear training or manual tuning.
- Activating Tone Generator: Press the "M/T" button until "Sound" or "Tone" is displayed.
- Selecting Reference Tone: Use the Up (▲) and Down (▼) arrow buttons to select the desired reference tone within the range of 2A to 6A.
- Volume: Adjust the volume using the volume control dial on the side of the device.
Maintenance
- Cleaning: Wipe the device with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
- Storage: Store the device in a dry place, away from extreme temperatures and direct sunlight. Remove batteries if the device will not be used for an extended period to prevent leakage.
- Handling: Avoid dropping the device or subjecting it to strong impacts.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Batteries are dead or incorrectly inserted. | Replace batteries with new ones, ensuring correct polarity. |
| Tuner is not detecting pitch accurately. | Incorrect tuning mode selected, instrument too far from mic, or background noise. | Ensure correct tuning mode (Chromatic or specific wind instrument key). Move instrument closer to the built-in microphone. Tune in a quiet environment. Check A4 calibration. |
| No sound from metronome or tone generator. | Volume is too low or muted. | Adjust the volume control dial on the side of the device. |
Specifications
| General | |
|---|---|
| Model Number | WMT-578RC |
| Product Name | Flute/Sax Tuner Metronome |
| Brand Name | Cherub |
| Type | Tuner |
| Material | Metal, Plastic |
| Color | Black, Red |
| Screen | LCD display |
| Power Supply | 3V (2xAAA batteries, not included) |
| Dimensions (W x D x H) | 100mm x 19mm x 63mm |
| Weight | 0.1 kg |
| Origin | Mainland China |
| Tuner | |
| Tuning Range | A0(27.5Hz)~C8(4186Hz) |
| Tuning Mode | Chromatic, Wind instruments (C, F, B♭, E♭) |
| Tuning Precision | ±1 cent |
| A4 Range | 430~450Hz |
| Detection Method | Mic, Line-in |
| Display Mode | Color LCD display, LED display |
| Tuning Method | Auto |
| Tone Generator | |
| Reference Tone Range | 2A~6A |
| Reference Tone Precision | ±0.5 cent |
| Metronome | |
| Tempo Range | 30~250 bpm |
| Beat | 0~9 |
| Tempo Precision | ±0.3% |
| Metronome Sound | Electronic sound |

Image: Dimensions of the Cherub WMT-578RC Tuner Metronome (100mm x 63mm).
User Tips
- This tuner metronome is specifically designed for wind instruments such as saxophones and flutes, ensuring optimal performance for these instruments.
- Users have noted the product offers good value for its functionality.
Warranty and Support
For detailed warranty information and customer support, please refer to the official product documentation or contact the seller directly.
A digital version of the user manual is available in PDF format: View User Manual (PDF)