retekess TD173

Contents

RETEKESS TD173 Coaster Pager Receiver User Manual

Instructions for the TD173 Series Guest Paging System Receiver

Introduction

Thank you for choosing the Retekess TD173 Coaster Pager Receiver. This product is designed to expand your existing TD173 Guest Paging System, providing additional pagers for efficient customer notification in various service environments such as restaurants, coffee shops, food courts, and clinics. The system utilizes RF wireless technology for reliable communication.

This manual provides detailed instructions for setting up, operating, and maintaining your pager receivers, ensuring optimal performance and longevity.

Safety Information

Before using this product, please read this guide carefully. It contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

RF Energy Exposure and Product Safety Guide

  • Unauthorized Modification and Adjustment: Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this radio. Transmitter adjustments should only be made by certified technicians.
  • FCC Requirements: This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • CE Requirements: The radio equipment type is in compliance with essential requirements of RED Directive 2014/53/EU, ROHS Directive 2011/65/EU, and WEEE Directive 2012/19/EU.
  • Disposal: Do not dispose of electrical and electronic products, batteries, and rechargeable batteries as unsorted municipal waste. Dispose of them according to local laws.

Avoid Choking Hazard

The product contains small parts. Keep out of reach of children under 3 years.

Protect Your Hearing

  • Use the lowest volume necessary.
  • Increase volume only in noisy surroundings.
  • Turn down volume before adding headset or earpiece.
  • Limit time using headsets/earpieces at high volume.
  • When using the radio without a headset/earpiece, do not place the speaker directly against your ear.
  • Excessive sound pressure from earphones and headphones can cause hearing loss.

Setup and Initial Use

1. Charging the Pagers

Before first use, or if pagers are not charged, place them onto the charging slots of your TD173 transmitter. Ensure the transmitter is connected to its power supply.

  • The charging indicator on the pager will flash quickly during charging.
  • The indicator will stay on when fully charged.
  • Pagers automatically turn on and begin charging when inserted into the charging slot.
  • After removing a pager, the charging indicator flashes slowly, indicating standby mode and readiness for calls.
Pager with charging indicator and battery icon
Pager showing long standby time and LED charging indicator.

2. Paring Operation (Adding New Pagers)

To add new pager receivers to your TD173 system, follow these steps:

  1. Ensure the transmitter is in charging mode.
  2. Press the SET key on the transmitter to enter setting mode. F1 will be shown on the display.
  3. Press the CALL key to enter the paring mode. The charging indicators on pagers will turn off, and other indicators will turn on. 000 will show on the display.
  4. Remove a pager from the charging slot. Within 10 seconds, enter a desired number (1-998) for the pager using the transmitter's keyboard.
  5. Press the CALL key to confirm. The pager will beep, indicating successful pairing.
  6. Repeat steps 4 and 5 to pair other pagers.
  7. Press the BACK key twice to exit the setting mode.

Note: If there is no operation within 10 seconds after removing the pager from the charging slot, the system will automatically exit the pairing mode.

Front and side view of the TD173 pager receiver
Front and side view of the TD173 Pager Receiver.

Operating Instructions

1. Calling a Pager

  • Ensure the transmitter is in Call Mode (display shows 000).
  • If in another mode, continuously press the BACK key to return to Call Mode.
  • Enter the desired pager number (1-998) using the keyboard.
  • Press the CALL key to activate the corresponding pager.

2. Checking Call History

  • Press the △ or ▽ key on the transmitter to display recently called numbers.
  • The transmitter can store up to 10 recent called numbers.
  • To re-call a number from the history, press the CALL key when the number is displayed.

Note: Paging up and down through history does not cycle.

3. Turning Off Pagers

To turn off all pagers that are currently charging:

  1. In Call Mode, enter 999.
  2. Press the CALL key. All charging pagers will turn off.
  3. The charging indicators will turn off for 5 seconds, then light up again to indicate charging status.
  4. The indicator light goes out when a pager is removed from its charging slot after being shut down.

To turn pagers back on, simply insert them into the charging slots with the transmitter connected to power.

Note: This instruction is not valid for pagers that are not currently charging.

4. One-Click Mute Feature

Each pager receiver is equipped with a one-click mute button, allowing customers to easily turn off the sound notification. This provides flexibility and comfort for guests.

Pager with one-click mute button highlighted
The one-click mute button on the pager receiver.

Advanced Settings (Transmitter)

These settings are configured on the TD173 transmitter and affect the behavior of the pager receivers.

1. Prompt Settings (F2) - Reminder Modes

To change the reminder mode for pagers:

  1. On the charging mode, press SET to enter setting mode (F1 displayed).
  2. Press the △ key once. F2 will be displayed.
  3. Press CALL to enter the sub-menu.
  4. Use the △ or ▽ keys to select the desired prompt mode value (see Code Description below).
  5. Press CALL to confirm. The transmitter will beep, and F2 will be displayed, indicating the setting is complete.
  6. Press BACK to exit the setting mode.

Code Description for Prompt Modes:

  • 000: Mute (no prompt)
  • 001: Beep
  • 002: Vibration
  • 003: Beep and Vibration
  • 004: Pager prompt mode: Beep
  • 005: Pager prompt mode: Vibration
  • 006: Pager prompt mode: LED Flash
  • 007: Pager prompt mode: Beep and Vibration
  • 008: Pager prompt mode: Vibration and LED Flash
  • 009: Pager prompt mode: Beep and LED Flash
  • 010: Pager prompt mode: Beep, Vibration, and LED Flash
Diagram showing 7 reminder modes for pagers
Available reminder modes: Vibration + Flash, Vibration, Flash, Beep + Vibration + Flash, Beep + Vibration, Beep + Flash, Beep.

2. Prompt Time Setting (F3)

To set the duration of the pager prompt:

  1. On the charging mode, press SET to enter setting mode (F1 displayed).
  2. Press the △ key twice. F3 will be displayed.
  3. Press CALL to enter the sub-menu.
  4. Enter the desired prompt time (1-999 seconds) using the keyboard.
  5. Press CALL to confirm. The transmitter will beep, and F3 will be displayed.
  6. Press BACK to exit the setting mode.

3. Transmitter ID Setting (F4)

To change the transmitter's ID:

  1. On the charging mode, press SET to enter setting mode (F1 displayed).
  2. Press the △ key three times. F4 will be displayed.
  3. Press CALL to enter the sub-menu.
  4. Enter the desired transmitter ID (1-999) using the keyboard.
  5. Press CALL to confirm. The transmitter will beep, and F4 will be displayed.
  6. Press BACK to exit the setting mode.

Important Note: You must re-pair all pagers after changing the transmitter ID.

Maintenance

1. Changing Advertising Paper

The pager receivers allow for customized advertising inserts. To change the paper:

  • Carefully remove the transparent cover from the pager.
  • Insert your desired advertising paper into the designated slot.
  • Replace the transparent cover securely.
Diagram showing how to customize the pager with ad paper and transparent cover
Customizing the pager with ad paper and transparent cover.

2. Cleaning

To maintain the cleanliness and functionality of your pagers and charging base, wipe them with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials that could damage the surfaces.

Troubleshooting

  • Pager not responding: Ensure the pager is charged. If it was recently removed from the charging slot, ensure it was paired correctly. If the transmitter ID was changed, all pagers must be re-paired.
  • Paring mode exits automatically: If no operation is performed within 10 seconds after removing a pager from the charging slot during paring, the system will exit paring mode. Re-enter paring mode and try again.
  • Pagers not turning off: Ensure pagers are placed in the charging slots and the transmitter is connected to power before attempting to turn them off using the 999 + CALL sequence. This function is only valid for pagers that are currently charging.

Specifications

FeaturePager
BatteryLi-ion 3.7V 200mAh
Frequency433.92MHz
Standby Current<12mA
Sensitivity-108dBm
Prompt ModeVibration/Buzzer/Flashing
Prompt Time1-999s
MaterialPC+ABS
Dimensions100*50*10mm
Detailed specifications table for the pager
Detailed specifications for the TD173 Pager Receiver.

User Tips

  • Expanding Your System: These 10-piece pager sets are designed to expand an existing TD173 system. If you need to add more pagers, you can purchase additional sets and pair them using the instructions provided in the "Paring Operation" section.
  • Custom Pager Numbers: When pairing new pagers, you can assign any number from 1 to 998. This allows for flexible numbering schemes to suit your operational needs.
  • Replacing Lost Pagers: If a pager is lost or damaged, a single replacement pager can be purchased and paired to your existing system following the "Paring Operation" steps.

Warranty and Support

1. Guarantee Information

Most new Retekess products carry a two-year manufacturer's warranty from the date of purchase. Please retain your guarantee card and proof of purchase for verification.

  • To obtain warranty service, contact the seller where you purchased the product.
  • Products may be repaired by a local repair center.

Exclusions from Warranty Coverage:

  • Damage caused by accident.
  • Misuse, abuse, unauthorized alterations, or repairs.
  • Products with altered, defaced, or removed serial numbers.

2. Manufacturer Contact

For support or inquiries, you may contact the manufacturer:

  • Company: Henan Eshow Electronic Commerce Co., Ltd
  • Address: 7/F, Sanjiang Building, No.170 Nanyang Road, Huiji District, Zhengzhou, Henan, China
  • E-mail: support@retekess.com
  • Website: www.retekess.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.