Estardyn BBX1-8S

Contents

User Manual: 1-8S Lipo Battery Voltage Tester / Low Voltage Buzzer Alarm

Model: BBX1-8S

Introduction

This manual provides instructions for the Estardyn 1-8S Lipo Battery Voltage Tester and Low Voltage Buzzer Alarm (Model BBX1-8S). This device is designed to accurately measure the voltage of 1-8S Lipo, Li-ion, LiMn, and Li-Fe batteries and alert users to low voltage conditions with an audible buzzer and visual LED indicator. It is an essential tool for RC enthusiasts and anyone using multi-cell lithium batteries.

Estardyn 1-8S Lipo Battery Voltage Tester and Low Voltage Buzzer Alarm, showing both cased and uncased versions.

Figure 1: Estardyn 1-8S Lipo Battery Voltage Tester (BBX1-8S).

Specifications

FeatureValue
Battery Type Compatibility1-8S Lipo / Li-ion / LiMn / Li-Fe
Voltage Detection Precision±0.01V
Unit Voltage Display Range0.5V - 4.5V
Total Voltage Display Range0.5V - 36V
1S Test Mode Voltage Range3.7V - 30V
Low Voltage Alarm ModeFor 2-8S batteries
Alarm Set Value RangeOFF - 2.7V - 3.8V
Pre-set Alarm Value3.3V
Dimensions3.9cm x 2.4cm x 0.9cm
Operating Temperature-40°C to +85°C

The device features a digital LED display for clear voltage readings and dual speakers for an audible low voltage alarm.

Setup and Connection

Before use, ensure the battery type matches the device's compatibility (1-8S Lipo/Li-ion/LiMn/Li-Fe).

  1. Identify Battery Balance Port: Locate the balance charging port on your Lipo/Li-ion/LiMn/Li-Fe battery. This port typically has multiple pins.
  2. Connect the Tester: Plug the tester's balance port connector into your battery's balance port. Ensure the negative (-) terminal of the tester aligns with the negative terminal of the battery's balance port. The pins are usually labeled on the battery or the tester.
  3. Power On: Once connected, the tester will automatically power on and display the total voltage of the battery, followed by the individual cell voltages.
Diagram showing how to connect the battery voltage tester to a Lipo battery's balance port, indicating positive and negative terminals.

Figure 2: Battery Connection Diagram. Connect the tester to the battery's balance port, ensuring correct polarity.

Back view of the Lipo Battery Voltage Tester showing specifications and a push button for settings.

Figure 3: Rear view of the tester with specifications and setting button.

Operating Instructions

Voltage Display:

  • Upon connection, the device will first display the total voltage of the battery pack.
  • It will then cycle through and display the voltage of each individual cell (e.g., 1S, 2S, 3S, etc.).
  • The red LED display provides clear readings.

Low Voltage Alarm Setting:

The low voltage alarm function is available for 2-8S batteries. The pre-set alarm value is 3.3V per cell.

  1. Locate the small push button on the side of the tester (refer to Figure 3).
  2. Press the button to cycle through the alarm set values: OFF, 2.7V, 2.8V, ..., up to 3.8V.
  3. Release the button when the desired alarm voltage is displayed. The setting will be automatically saved.
  4. When the voltage of any individual cell drops below the set alarm value, the device will emit a loud buzzer sound and a red LED light will illuminate to indicate a low voltage condition.
Front view of the 1-8S Lipo Battery Voltage Tester showing the digital display and dual speakers.

Figure 4: Front view of the tester displaying voltage and showing dual speakers.

Maintenance

  • Keep the device clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
  • Avoid exposing the tester to extreme temperatures or direct sunlight for prolonged periods.
  • Store the device in a safe place when not in use to prevent physical damage to the pins or casing.
  • Do not attempt to disassemble or modify the device, as this may void any potential warranty and could cause damage.

Troubleshooting

  • No Display/No Power:
    • Ensure the battery is properly connected to the balance port with correct polarity.
    • Verify that the battery itself has sufficient charge.
    • Check for any bent or broken pins on the tester or battery balance lead.
  • Alarm Not Sounding:
    • Confirm that the alarm set value is not set to "OFF".
    • Ensure the battery is a 2-8S type, as the alarm mode is not active for 1S batteries.
    • Check if any cell voltage is actually below the set alarm threshold.
  • Inaccurate Readings:
    • Ensure all connections are secure and clean.
    • Test with a known good battery to verify device functionality.
    • Avoid using the tester in environments with extreme electromagnetic interference.

User Tips

  • Always connect the tester to the battery's balance port before connecting the main power leads to your device (e.g., RC model) to monitor voltage from the start.
  • Set the low voltage alarm slightly higher than your ESC's (Electronic Speed Controller) cut-off voltage to provide an earlier warning and prevent over-discharge.
  • Regularly check individual cell voltages, not just total voltage, to identify any unbalanced cells which can affect battery performance and lifespan.
  • When storing batteries, ensure they are at a safe storage voltage (typically around 3.8V per cell for LiPo) and use the tester to confirm.

Warranty and Support

Specific warranty information for this product is not provided in the available documentation. For any warranty claims, technical support, or service inquiries, please contact the seller or manufacturer directly.

Manufacturer: Estardyn

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.