Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of FGHGF replacement parts for the Jashen S10 Robot Vacuum Cleaner. These parts include the main roller brush, side brushes, HEPA filters, and mop cloths. Regular replacement and maintenance of these components are crucial for ensuring the optimal performance and longevity of your robot vacuum cleaner.

Figure 1: Assortment of FGHGF replacement parts for Jashen S10 robot vacuum cleaner.
Setup and Installation
Before installing any replacement parts, ensure your Jashen S10 robot vacuum cleaner is powered off and disconnected from its charging base. Always refer to your robot vacuum's original manual for specific safety precautions.
1. Side Brushes Installation
- Turn the robot vacuum cleaner upside down.
- Locate the side brushes. They are usually held in place by a screw.
- Unscrew the old side brush and carefully remove it.
- Align the new side brush (Figure 2) with the corresponding slot and screw it into place. Ensure it is securely fastened but not overtightened.

Figure 2: Replacement side brushes.
2. Main Roller Brush Installation
- Turn the robot vacuum cleaner upside down.
- Locate the brush guard or cover, typically secured by clips or latches.
- Open the guard and remove the old main roller brush.
- Insert the new main roller brush (Figure 3), ensuring the ends align correctly with the brush unit's slots.
- Close the brush guard until it clicks into place.

Figure 3: Replacement main roller brush.
3. HEPA Filter Installation
- Open the dustbin compartment of your robot vacuum.
- Remove the dustbin.
- Locate the filter assembly within the dustbin. Remove the old HEPA filter.
- Place the new HEPA filter (Figure 4) into the designated slot, ensuring it fits snugly to maintain proper filtration.
- Reinsert the dustbin into the robot vacuum until it locks.

Figure 4: Replacement HEPA filters.
4. Mop Cloth Installation
- If your Jashen S10 model supports mopping, locate the mop pad attachment.
- Remove the used mop cloth.
- Attach the new mop cloth (Figure 5) to the mop pad, ensuring it is flat and covers the entire surface.
- Reattach the mop pad to the robot vacuum if it was removed.

Figure 5: Replacement mop cloths.
Operating with New Parts
Once all replacement parts are installed, you can resume normal operation of your Jashen S10 robot vacuum cleaner. The new components are designed to integrate seamlessly and restore the vacuum's cleaning efficiency.
- Initial Run: After replacing parts, it is recommended to perform a short cleaning cycle to ensure all components are functioning correctly.
- Performance Check: Observe the vacuum's cleaning performance. You should notice improved dust pickup, debris collection, and mopping effectiveness (if applicable).
- Noise Levels: New brushes might initially produce slightly different sounds, which should normalize after a few cleaning cycles.
Maintenance
Regular cleaning and timely replacement of these parts are essential for maintaining your robot vacuum's performance.
Side Brushes
- Cleaning: Periodically check for tangled hair or debris. Use scissors or a small brush to remove any obstructions.
- Replacement: Replace side brushes every 3-6 months, or sooner if they become visibly worn, bent, or damaged, as this can affect edge cleaning.
Main Roller Brush
- Cleaning: Remove the main brush after each few uses. Use the cleaning tool provided with your vacuum (or a similar tool) to cut and remove tangled hair and fibers from the brush bristles and ends.
- Replacement: Replace the main roller brush every 6-12 months, or if bristles are significantly worn or damaged, impacting cleaning effectiveness.
HEPA Filters
- Cleaning: Tap the filter gently over a trash can to dislodge dust and debris. Do NOT wash HEPA filters with water unless explicitly stated by the manufacturer, as this can damage the filter material.
- Replacement: Replace HEPA filters every 1-3 months, depending on usage frequency and pet presence. A clogged filter reduces suction power and air quality.
Mop Cloths
- Cleaning: After each mopping session, remove the mop cloth and wash it thoroughly with water and mild detergent. Allow it to air dry completely before reuse.
- Replacement: Replace mop cloths every 3-6 months, or if they become stained, torn, or lose their absorbency.
Troubleshooting
If you encounter issues after replacing parts, consider the following common solutions:
- Reduced Suction Power: Check if the HEPA filter is correctly installed and not clogged. Ensure the dustbin is empty.
- Poor Debris Pickup: Verify that the main roller brush and side brushes are free of tangles and spinning correctly. Ensure they are installed securely.
- Vacuum Not Moving Straight/Turning: Inspect side brushes for damage or excessive wear.
- Wet Spots After Mopping: Ensure the mop cloth is clean and properly attached. Check the water tank for proper function (if applicable to your model).
- Unusual Noises: Remove and re-install all brushes to ensure they are seated correctly. Check for any foreign objects caught in the brush mechanisms.
Specifications
| Attribute | Detail |
|---|---|
| Material | PP, Fabric, PVC, ABS Plastic |
| High-concerned chemical | None |
| Vacuum Part Type | BRUSHES |
| Model Number | for jashen s10 |
| Brand Name | FGHGF |
| Origin | Mainland China |
| Type | Vacuum Cleaner Parts |
| Compatible Parts | Side brush, Hepa filter, Cleaning mop, Roller brush, Mop cloth, Mop rags |
User Tips
- Regular Checks: Make it a habit to quickly check brushes and filters for debris after each cleaning cycle, especially if you have pets.
- Stock Up: Consider keeping a spare set of filters and brushes on hand so you can replace them immediately when needed, avoiding downtime for your vacuum.
- Gentle Cleaning: When cleaning filters, tap them gently. Avoid harsh brushing or washing unless the filter is specifically designed for it, as this can damage the delicate filter material.
- Mop Cloth Care: For best mopping results, pre-wet the mop cloth before attaching it to the vacuum. This helps ensure even moisture distribution from the start of the cleaning cycle.
Warranty and Support
For any questions regarding the FGHGF replacement parts or for support, please contact the seller directly through the platform where the purchase was made. Ensure you retain your purchase records for any warranty claims or support inquiries.
For detailed instructions on your Jashen S10 robot vacuum cleaner, including part replacement visuals and troubleshooting, please consult the official user manual. A PDF version of the item guide is available and can be viewed here.