SUSWE SUSWE 820

Contents

SUSWE 820 Variable Frequency Drive (VFD) Instruction Manual

Single-Phase 220V Input to Three-Phase 220V Output Motor Driver

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the SUSWE 820 Variable Frequency Drive (VFD). This device is designed to convert single-phase 220V input power into three-phase 220V output, enabling precise control over three-phase AC motors. It is suitable for applications requiring motor fan speed regulation, constant pressure water supply by water pump, and general energy-saving motor control.

Key Features:

  • Vector overload type for enhanced motor control.
  • Output power options: 750W (0.75KW) and 1500W (1.5KW).
  • Output Frequency range: 1.0-99.0Hz.
  • Built-in radiator for efficient heat dissipation.
  • Compact design for easy integration.

2. Safety Information

Please read and understand all safety warnings and instructions before installing, operating, or performing maintenance on the VFD. Failure to comply with these instructions may result in electric shock, fire, serious injury, or death.

  • Ensure the power supply is disconnected before any wiring or maintenance work.
  • Only qualified personnel should install and service this equipment.
  • Verify correct voltage and current ratings for the VFD and motor.
  • Do not touch electrical components when power is applied.
  • Ensure proper grounding of the VFD and motor.
  • Keep the VFD away from moisture, dust, and corrosive environments.
  • Do not operate the VFD with damaged cables or terminals.

3. Product Overview

3.1. Dimensions

The SUSWE 820 VFD features a compact design. Refer to the diagram below for detailed dimensions.

SUSWE 820 VFD Dimensions
Figure 1: SUSWE 820 VFD Dimensions (Length: 60.5mm, Height: 102.5mm, Depth: 130mm)

3.2. Control Panel Layout

The front panel provides all necessary controls and indicators for operation and parameter setting.

SUSWE 820 VFD Control Panel Layout
Figure 2: Control Panel Overview

3.3. Key Descriptions

The following table details the function of each key on the control panel:

SUSWE 820 VFD Key Descriptions
Figure 3: Detailed Key Descriptions
  • MODE key: View set frequency (Fxxx), operating frequency (Hxxx), operating current (Axxx), motor direction (FWD/REV), input voltage (Uxxx), inverter temperature (Txxx), input point status (Lxxx), PID parameter display (X.X-X X), and setpoint/feedback value.
  • ▲ (UP) key: Add function when setting data or add frequency when frequency is controlled by panel.
  • ▼ (DOWN) key: Subtract data function when setting data or reduce frequency when frequency is controlled by panel.
  • ENTER key: Press to enter parameter mode when setting Pxxx parameters, and press again to save parameters after modification.
  • JOG key: Initiates jog operation function.
  • RUN key: Starts inverter panel operation.
  • STOP / RESET key: Stops operation mode and clears fault alarm function in fault display mode.
  • ENTER +: Composite key. In panel lock mode, press this key to unlock the function. When panel lock is enabled, press this key to enter panel lock function.

Description of panel settings: When the panel displays Pxxx, use the UP and DOWN arrow buttons to adjust the specified parameter number, then press ENTER to enter the data mode of this menu item. Data can be modified to the specified size according to the table. After modification, press ENTER to save. If the panel does not display Pxxx mode, press the MODE key until Pxxx is displayed.

4. Setup (Installation and Wiring)

4.1. Mounting

The VFD is designed for panel mounting. Ensure adequate ventilation around the unit. The recommended opening size for installation is 52.5mm x 80mm x 130mm.

4.2. Wiring

All wiring must be performed by a qualified electrician. Ensure the power supply is disconnected before connecting any wires. Refer to the wiring diagram below for proper connections.

SUSWE 820 VFD Wiring Diagram
Figure 4: Main Wiring Diagram
SUSWE 820 VFD Wiring Terminals
Figure 5: Wiring Terminal Labels

Terminal Descriptions:

  • L, N: Single-phase 220V AC input.
  • PE: Ground connection.
  • U, V, W: Three-phase output to the motor.
  • CM, NC, ON: Relay output terminals.
  • YO, 12V/P: Multi-function composite output point (YO point is a multi-function composite output point. Only one of brake resistor and general transistor output can be used).
  • X0, X1, X2, X3: External sensor inputs.
  • 12V, GND, 5V: Power supply for external sensors.
  • AI: Analog input (0-5V/0-10V).
  • A+, B-: 485 communication interface.

Note: For single-phase three-wire output, connect U, V, W to the motor. For single-phase two-wire output without dismantling, connect U, V to the motor. For encoder input, connect X2, X3, GND, 5V/12V.

5. Operating Instructions

5.1. Basic Operation

  1. Power On: Connect the VFD to the appropriate single-phase 220V power supply. The display will light up.
  2. Start Motor: Press the RUN key to start the motor.
  3. Stop Motor: Press the STOP / RESET key to stop the motor.
  4. Jog Operation: Press the JOG key for momentary motor operation.

5.2. Frequency Regulation

The VFD features a potentiometer on the front panel for regulating the output frequency. Turn the knob clockwise to increase the frequency and counter-clockwise to decrease it.

5.3. Parameter Settings

To access and modify parameters (Pxxx settings):

  1. Press the MODE key repeatedly until 'Pxxx' (e.g., P001) is displayed.
  2. Use the ▲ (UP) or ▼ (DOWN) keys to navigate to the desired parameter number.
  3. Press the ENTER key to enter the data modification mode for that parameter.
  4. Use the ▲ (UP) or ▼ (DOWN) keys to adjust the parameter value.
  5. Press the ENTER key again to save the new value.
  6. Press MODE to exit parameter setting mode.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your VFD.

  • Cleaning: Periodically clean the VFD's exterior and ventilation openings to prevent dust accumulation, which can hinder heat dissipation. Use a soft, dry cloth. Do not use liquid cleaners.
  • Inspection: Regularly check all wiring connections for tightness and signs of wear or damage. Inspect the cooling fan for proper operation and obstructions.
  • Environment: Ensure the operating environment remains within specified temperature and humidity ranges.

7. Troubleshooting

The VFD is equipped with fault detection capabilities. If an error occurs, a fault code will be displayed. Refer to the table below for common fault codes and their solutions.

SUSWE 820 VFD Fault Code Table
Figure 6: Fault Code Table
Alarm TypeFault DescriptionFault Comment
OCInstantaneous overcurrentCheck whether the motor is normal
OCAAcceleration overcurrentCheck whether the motor is normal
OCDDeceleration overcurrentAdjust the acceleration time appropriately
OCNConstant speed overcurrentAdjust the deceleration time appropriately
OUOverpressureCheck whether the machine is normal and the voltage is stable
LUUndervoltageAdjust the acceleration and deceleration time properly, and check whether the mains supply is normal (180V-240V)
OHInverter overheatingDetect whether the mains supply is normal
EFExternal faultDetect external sensors. Whether the input is normal
ERSFailure restart failedRestart the drive
LPInput phase failureCheck whether the mains supply is normal
OL1Motor overloadCheck whether the motor is normal and whether the load is too heavy
OL2Inverter overloadCheck whether the motor is normal and whether it matches the frequency converter power
OL3Temporary motor overloadCheck whether the motor matches the power of the frequency converter
OL4Temporary overload of frequency converterCheck whether the load matches the motor
485Communication failureCheck whether the communication line is normal, and whether the upper computer communication is normal
PIDPID failureCheck whether analog input is output and whether sensor is normal
NONo fault alarmCheck whether analog input is output and whether sensor is normal

8. Specifications

AttributeValue
Model NumberSUSWE-810 (Note: Product title refers to SUSWE 820)
TypeDC/AC Inverters
Input VoltageSingle-phase 220V
Output VoltageThree-phase 220V
Output Power750W (0.75KW) / 1500W (1.5KW)
Output Frequency1.0-99.0Hz
Weight0.5KG
Size (L*W*H)60.5mm * 102.5mm * 130mm (approx. 60*100*125 as per some specs)
OriginMainland China
CertificationCE

9. User Tips

  • Motor Compatibility: This VFD is designed for three-phase motors. Ensure your motor is compatible with a 220V three-phase supply. For example, a 1 HP motor (approx. 750W) should work well with the 750W variant.
  • Panel vs. Remote Control: The VFD can be operated directly from the control panel using the RUN/STOP keys and potentiometer. For remote control or advanced configurations, refer to the parameter settings for switching between digital and remote modes, and utilize the external sensor inputs or 485 communication interface as needed.
  • Parameter Configuration: Take time to understand the parameter settings (Pxxx) to optimize the VFD's performance for your specific application, such as adjusting acceleration/deceleration times to prevent overcurrent faults.

10. Warranty and Support

The SUSWE 820 VFD comes with a 1-year warranty from the date of purchase, covering manufacturing defects. For technical support, troubleshooting assistance, or warranty claims, please contact your seller or the manufacturer directly. Remote package debugging guidance may also be available.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.