1. Introduction
Thank you for choosing the Herdio HCS-4-628BT 6.5" Bluetooth Ceiling Speaker System. This system is designed to provide high-quality audio for various indoor and covered outdoor environments, including kitchens, home theaters, bedrooms, offices, and patios. This manual will guide you through the installation, operation, and maintenance of your new speaker system.
2. Package Contents
Please check the box for the following items:
- 4 x 6.5-inch Passive Ceiling Speakers (Model HCS818BT)
- 4 x Speaker Cables (5 meters each, red for positive +, black for negative -)
- 1 x 4-Channel Bluetooth Amplifier Box (Model AMP-BTX01)
- 1 x Power Adapter (12V3A, appropriate plug for your region: US/UK/AU/EU)
- 1 x User Manual (for speakers)
- 1 x User Manual (for amplifier)
- 1 x Cutout Template
- 4 x Gaskets

3. Specifications
| Feature | Specification |
|---|---|
| Model (System) | HCS-4-628BT |
| Model (Speaker) | HCS818BT |
| Speaker Size | 6.5 Inch |
| PMPO (Peak Music Power Output) | 600W |
| Max Power Output (per speaker) | 160W |
| Sensitivity | 89dB |
| Impedance | 8 Ohm |
| Frequency Range | 60Hz-23KHz |
| Cut-Out Diameter | 6.3 inches (16 cm) |
| Total Speaker Diameter | 7.5 inches (19 cm) |
| Mounting Depth | 3.15 inches (8 cm) |
| Bluetooth Version | 5.1 |
| Maximum Wireless Range | 10m-20m (33-66 ft) |
| Input/Output | AUX, Bluetooth |
| Power Source | AC (via 12V3A Power Adapter) |
| Voltage Range | USB (5-20V DC) |
| Cabinet Material | Plastic (ABS) |
| Waterproof | No |

4. Setup
4.1 Speaker Installation
- Prepare the Cutout: Use the provided cutout template to mark the desired location on your drywall or ceiling. Ensure there is at least a half-inch clearance between the wall stud/ceiling joist and the speaker cutout to allow the locking tabs to swivel into place. Carefully cut the drywall.
- Connect Speaker Wires: Connect the speaker cables to the speaker terminals. The red wire is for positive (+) and the black wire is for negative (-). The Herdio speakers feature spring-loaded terminals for easy connection. Press down on the terminal tab, insert the stripped wire, and release.
- Mount the Speaker: Insert the speaker into the cutout. Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall.
- Attach Grille: Replace the metal grille by gently pressing it into place.

4.2 Amplifier and Wiring Setup
- Connect Speakers to Amplifier: Connect the speaker cables from each of the four speakers to the corresponding L1+, L1-, R1+, R1-, L2+, L2-, R2+, R2- terminals on the 4-channel Bluetooth amplifier. Use a screwdriver to control the amplifier terminals, ensuring a secure connection for both red (positive) and black (negative) wires.
- Power Supply Connection: Plug the 12V3A power adapter into the PWR port on the amplifier box, then plug the adapter into a wall outlet.


Important Note on Amplifier Placement:
- Estimate the specific plug and the distance to the speakers BEFORE installation so that the wires are not long enough.
- This amplifier is NOT waterproof. Do not install it in an uncovered place or where it may be exposed to moisture.
5. Operating Instructions
5.1 Amplifier Controls

- Power (PWR): Long press to power on/off. Short press to play/pause.
- Mode: Long press to reset (restore factory settings). Short press to switch mode between Bluetooth, USB, AUX, and MIC.
- VOL-/TWS: Press and hold to turn on/off TWS (True Wireless Stereo) mode. Short press to decrease volume.
- VOL+/MONO: Press and hold to turn on/off Mono mode. Short press to increase volume.
- Previous Track: Press and hold for fast rewind. Short press for previous song.
- Next Track: Press and hold for fast forward. Short press for next song.
- USB Port: For USB input.
- AUX Port: For 3.5mm auxiliary input.
- MIC Port: For microphone input.
5.2 Bluetooth Pairing
- Ensure the power supply is connected to the amplifier. The blue LED on the amplifier should be flashing, indicating it is in pairing mode.
- Turn on your mobile device or other Bluetooth-enabled device.
- Scan for Bluetooth devices and select "Herdio" from the list.
- Once connected, you will hear a confirmation tone, and the blue LED on the amplifier will turn solid.
Note: The amplifier's blue light blinks during pairing and remains constant once connected.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the speakers and amplifier. Do not use harsh chemicals or abrasive cleaners.
- Avoid Moisture: The amplifier is not waterproof. Ensure it is installed in a dry location, away from direct exposure to water or high humidity. While the speakers are designed for covered outdoor patios, prolonged exposure to extreme moisture should be avoided.
- Grille Care: The speaker grilles are removable and paintable. If painting, ensure the paint is thin and does not clog the perforations, which could affect sound quality.
7. Troubleshooting
- No Sound:
- Check all speaker wire connections to ensure they are secure and correctly polarized (red to + and black to -).
- Verify the amplifier is powered on and the blue LED is solid, indicating a successful Bluetooth connection.
- Ensure the volume on both your source device and the amplifier is turned up.
- Confirm the correct input mode (Bluetooth, USB, AUX, MIC) is selected on the amplifier.
- Bluetooth Pairing Issues:
- Make sure the amplifier's blue LED is flashing, indicating it's in pairing mode. If it's solid, it's already connected to another device.
- Try resetting the amplifier by long-pressing the 'Mode' button to restore factory settings.
- Ensure your mobile device's Bluetooth is on and within the 10-20m range.
- Disconnect and reconnect the power to the amplifier.
- Distorted Sound:
- Reduce the volume on both the source device and the amplifier.
- Check speaker wire connections for any loose strands or short circuits.
- Ensure the audio source is of good quality.
- Multiple Music Streams: The system supports a single Bluetooth connection to the amplifier. You cannot stream different music to different speakers simultaneously from separate devices. All connected speakers will play the same audio from the paired device.
8. User Tips
- Users have reported excellent sound quality once the speakers are properly mounted.
- Ensure all wiring is correctly done, paying attention to positive and negative terminals, for optimal performance.
- Consider the amplifier's placement carefully, as it is not waterproof.
9. Warranty & Support
All Herdio speaker products come with a 1-year limited warranty against defects in materials and workmanship. Proof of purchase is required for all claims. During the warranty period, Herdio will replace any defective part and correct any manufacturing defects free of charge for parts or labor. The customer is not responsible for labor costs.
For questions or support, please contact us:
Email: support@herdiotech.com
Website: www.herdiotech.com
10. FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.