Kunray G51, GZ3, S830 Displays with 250W/350W/500W Controllers

Contents

Kunray Ebike/E-Scooter Controller Kit Instruction Manual

Models: G51, GZ3, S830 Displays with 250W/350W/500W Controllers

1. Important Safety Information

Please read this manual carefully before installation and use. Failure to follow instructions may result in damage to the product or personal injury.

⚠️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.

  • Ensure all connections are secure before powering on.
  • Do not attempt to modify the controller or display.
  • Keep the components away from water and extreme temperatures.
  • Always wear appropriate safety gear when operating an e-bike or e-scooter.

2. Product Overview

This kit provides essential components for controlling your e-bike or e-scooter, including a brushless DC motor controller and a display unit (G51, GZ3, or S830), along with throttle, brake levers, and a headlight.

Overview of Kunray Ebike Kit Components
Figure 2.1: Overview of Kunray Ebike Kit Components (Controller, Display, Throttle, Brake Levers, Headlight)

2.1. Components Included

  • Brushless DC Motor Controller (250W/350W or 500W)
  • Display Unit (G51, GZ3, or S830)
  • Thumb Throttle
  • Brake Levers
  • Control Switch
  • Headlight
  • PAS Sensor (Pedal Assist System)
Individual Ebike Kit Components
Figure 2.2: Individual Ebike Kit Components (Throttle, Brake Levers, Switch, Headlight)

3. Specifications

FeatureSpecification
Motor StyleBrushless
Rated Voltage24V / 36V / 48V
Rated Power350W / 500W
Current15A (for 350W), 17A (for 500W)
Controller Size (250W/350W)85mm (L) x 52mm (W) x 30mm (H)
Controller Size (500W)121mm (L) x 50mm (W) x 30mm (H)
Controller Weight (250W/350W)185g (approx.)
Display Shell MaterialABS
Display Gear Mode (G51)1-3
Display Gear Mode (S830, GZ3)1-5
Display Net Weight (G51)120g
Display Net Weight (S830)210g
Display Net Weight (GZ3)130g
Waterproof RatingIP65 (for displays)
Controller Dimensions (85x53x30mm)
Figure 3.1: Controller Dimensions (250W/350W)
Controller Dimensions (121x50x30mm)
Figure 3.2: Controller Dimensions (500W)
G51 Display Basic Information and Function Settings
Figure 3.3: G51 Display Basic Information and Function Settings
S830 Display Basic Information and Function Settings
Figure 3.4: S830 Display Basic Information and Function Settings
GZ3 Display Basic Information and Function Settings
Figure 3.5: GZ3 Display Basic Information and Function Settings

4. Setup and Installation

Follow these steps to correctly install and connect your e-bike controller kit. Ensure the e-bike's power is OFF before starting any installation.

4.1. Wiring Connections

Refer to the wiring diagrams below for proper connection of all components to the controller. Each connector is typically color-coded or uniquely shaped to prevent incorrect connections.

Comprehensive Ebike Controller Wiring Diagram
Figure 4.1: Comprehensive Ebike Controller Wiring Diagram (All components including display, motor, throttle, brake, PAS sensor, battery, headlight)

4.1.1. 250W/350W Controller Wiring

250W/350W Controller Wiring Diagram
Figure 4.2: Wiring Diagram for 250W/350W Brushless DC Motor Controller

4.1.2. 500W Controller Wiring

500W Controller Wiring Diagram
Figure 4.3: Wiring Diagram for 500W Brushless DC Motor Controller

4.2. Display Installation

Mount the display unit securely on your e-bike handlebars. Ensure it is within easy reach and view for safe operation.

S830 Display Mounted on Handlebars
Figure 4.4: S830 Display Mounted on Handlebars
G51 Display Mounted on Handlebars
Figure 4.5: G51 Display Mounted on Handlebars

5. Operating Instructions

This section covers the basic operation of your Kunray e-bike display and controller kit.

5.1. Basic Display Functions (G51, GZ3, S830)

The display units (G51, GZ3, S830) offer various functions for monitoring and controlling your e-bike. While specific button layouts may vary slightly, the core functionalities are similar.

G51 Display Functions
Figure 5.1: G51 Display Functions (Mileage, Switch, Mode, Electricity, Brightness, Fault, Voltage, Speed, Headlight)
S830 Display Functions
Figure 5.2: S830 Display Functions (Mileage, Switch, Mode, Electricity, Key Setting, Fault, Gear, Speed, Headlight)
GZ3 Display Functions
Figure 5.3: GZ3 Display Functions (Mileage, Switch, Mode, Electricity, Brightness, Fault, Voltage, Speed, Headlight)

5.2. Display Operation (Refer to Video)

Video 5.1: Demonstration of connecting the display to the controller and basic display functions.

  1. **Power On/Off**: Long press the 'M' key to turn the display on or off.
  2. **Adjust Gear/Assist Level**: Press '+' or '-' to increase or decrease the assist gear level.
  3. **Mode Selection**: Double-click the 'M' key to enter mode selection (P01, P02, etc.). Use the 'M' key for single-point adjustment within modes.
  4. **Headlight Control**: Long press '+' to turn on/off the headlights.
  5. **Cruise Control**: Long press '-' to turn on/off cruise control.

5.3. Display Setting Parameters (G51, GZ3, S830)

To enter the display settings, press the '+' and '-' buttons together. Use the 'M' key to navigate through parameters (P01-PXX) and '+' or '-' to adjust values.

ParameterDescriptionRange/Notes
P01Backlight Brightness1 (Lowest), 3 (Brightest)
P02Mileage Unit Setting0: km, 1: mile
P03Voltage Setting24V, 36V, 48V
P04Sleep Time0: No Sleep, Other Numbers: 1-60 Minutes
P05Power/Gear Adjustment3, 5, 9 (Can Be Selected)
P06Wheel DiameterUnit: inch, Accuracy: 0.1
P07Magnet Poles Range1-100
P08Speed Limit0-100km/h
P09Zero / Non-zero Start0: Zero Start, 1: Non-zero Start
P10Drive Mode Setting0: Power Drive (Now Throttle Invalid), 1: Electric Drive (Drive by Throttle), 2: Both power assist drive and electric drive.
P11Boost Sensitivity SettingRange: 1-24
P12Boost Start Strength SettingRange: 1-5
P13PAS Assist Type Setting(5/8/12) Single Hall PAS: Set to 5/8, Double Hall PAS: Set to 12
P16ODO ClearLong press up button 5 seconds to clear.

Note: What we send is the standard manual; the function will be different if the version is different. Due to manual measurement, 1-3 mm error occurs.

6. Maintenance

Proper maintenance ensures the longevity and optimal performance of your e-bike controller kit.

  • **Cleaning**: Regularly wipe down the display and controller with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • **Water Resistance**: The display has an IP65 waterproof rating. While it can withstand splashes, avoid submerging it in water. If used in rainy conditions, wipe it dry promptly after use.
  • IP65 Waterproof Display
    Figure 6.1: IP65 Waterproof Display. Please wipe dry after use in rain.
  • **Connection Checks**: Periodically inspect all wiring connections for any signs of wear, corrosion, or looseness. Secure any loose connections.
  • **Storage**: When not in use for extended periods, store the e-bike and its components in a dry, cool place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

If you encounter issues with your e-bike controller kit, refer to the following common problems and solutions.

7.1. Fault Display

The display unit can show fault codes to indicate specific issues. Refer to the display's function diagram for the "Fault display" icon.

  • **No Power on Display**:
    • Check battery connection and charge level.
    • Ensure the display cable is securely connected to the controller.
    • Verify the 'M' button is long-pressed to power on.
  • **Motor Not Responding**:
    • Check motor phase and Hall sensor connections.
    • Ensure throttle and PAS sensor are correctly connected and functioning.
    • Verify the drive mode setting (P10) on the display.
  • **Incorrect Speed/Mileage Reading**:
    • Check wheel diameter setting (P06) on the display.
    • Verify mileage unit setting (P02).
  • **Headlight Not Working**:
    • Ensure headlight is properly wired to the controller.
    • Long press '+' on the display to activate the headlight.

For persistent issues or specific error codes not listed, consult a qualified technician or contact customer support.

8. User Tips

  • **Initial Setup**: Take your time during the initial wiring. Double-check each connection against the provided diagrams to avoid short circuits or component damage.
  • **Display Customization**: Experiment with the display settings (P01-P16) to personalize your riding experience, such as backlight brightness, speed limit, and assist levels.
  • **Water Protection**: Even with IP65 rating, it's good practice to cover the display and controller during heavy rain or when washing the bike to prevent moisture ingress over time.
  • **Cable Management**: Use zip ties or cable wraps to neatly secure all wires, preventing them from snagging or getting damaged during rides.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the Kunray Official Store directly through your purchase platform. Keep your order details handy for faster assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.