Dooya DC1600

Contents

Dooya DC1600 Single Channel Emitter User Manual

Smart 433MHz Remote Control for Dooya Motor Roller Blinds and Zebra Blinds

1. Product Overview

The Dooya DC1600 is a single-channel radio frequency (RF) emitter designed to control Dooya motor-driven roller blinds and zebra blinds. It operates on a 433MHz frequency, providing convenient and reliable control over your automated window treatments.

Dooya DC1600 Single Channel Emitter remote control and its packaging.
Figure 1: Dooya DC1600 Single Channel Emitter

Package Contents:

  • Dooya DC1600 Single Channel Emitter
  • Mounting screws (typically included for wall mount)
  • User Manual (this document)

Note: Battery (CR2450) is not included and must be purchased separately.

2. Specifications

FeatureSpecification (DC1600)
Model NumberDooya DC1600
Control ChannelsSingle Channel
Max Receivers per Channel20 receivers
Power Supply3V (1 unit CR2450 battery)
Battery Service Life>2 years
Emission Distance (Outdoor)200 meters
Emission Distance (Indoor)35 meters
Emission Frequency433.92MHz ± 100KHz
Dimensions (L x W x H)130mm x 44mm x 10.5mm
Wattage0.03W
CertificationCE
Comparison table of Dooya DC1600, DC1602, and DC1603 remote control emitters with their respective specifications.
Figure 2: Dooya Emitter Series Comparison (DC1600, DC1602, DC1603)

3. Setup

3.1 Battery Installation

  1. Locate the battery compartment on the back of the DC1600 emitter.
  2. Open the battery compartment cover.
  3. Insert one CR2450 3V battery, ensuring correct polarity (+/-).
  4. Close the battery compartment cover securely.

Important: The CR2450 battery is not included in the package and must be purchased separately from a local market.

Diagram showing the front and back of the DC1600 and DC1602 remote controls, highlighting button functions and the battery compartment on the back.
Figure 3: DC1600 Button Layout and Back View (Battery Compartment)

3.2 Pairing with Dooya Motor

Refer to your Dooya motor's instruction manual for specific pairing procedures. Generally, the process involves:

  1. Ensure the motor is powered on.
  2. Activate the motor's pairing mode (often by pressing a small button on the motor head or receiver).
  3. Within a short timeframe (e.g., 5-10 seconds), press the "Up" button on the DC1600 emitter.
  4. The motor should respond (e.g., jog slightly, beep) to confirm successful pairing.
  5. Test the remote control to ensure full functionality (Up, Down, Stop).

4. Operating Instructions

The Dooya DC1600 Single Channel Emitter features three primary buttons for controlling your blinds:

Diagram showing the front and back of the DC1600 and DC1602 remote controls, highlighting button functions and the battery compartment on the back.
Figure 4: DC1600 Button Functions
  • Up Button (▲): Press to raise the blinds.
  • Stop Button (■): Press to stop the blinds at their current position.
  • Down Button (▼): Press to lower the blinds.

For optimal performance, ensure the remote is pointed towards the motor or receiver and within the effective indoor emission distance of 35 meters.

5. Maintenance

5.1 Cleaning

  • Wipe the remote control with a soft, dry cloth.
  • Do not use abrasive cleaners, solvents, or wet cloths, as these may damage the surface or internal components.

5.2 Battery Replacement

When the remote's range decreases or it becomes unresponsive, it's likely time to replace the battery. The battery service life is typically over 2 years.

  1. Follow the steps for battery installation (Section 3.1).
  2. Dispose of the old CR2450 battery according to local regulations.

5.3 Storage

  • Store the remote control in a dry place, away from direct sunlight and extreme temperatures.
  • If storing for an extended period, consider removing the battery to prevent leakage.

6. Troubleshooting

  • Remote not responding:
    • Check if the battery is correctly installed and has sufficient power. Replace the CR2450 battery if necessary.
    • Ensure the remote is within the effective operating range (35 meters indoors) and pointed towards the motor/receiver.
    • Verify that the motor is powered on and functioning correctly.
    • Re-attempt the pairing process (refer to your motor's manual).
  • Blinds move erratically or not to desired position:
    • This may indicate an issue with the motor's limit settings. Refer to your Dooya motor's instruction manual for adjusting limit positions.
    • Ensure no obstructions are blocking the blinds' path.

7. User Tips

  • Always keep a spare CR2450 battery on hand to avoid interruptions in control.
  • For optimal signal transmission, avoid placing large metal objects or other strong RF interference sources between the remote and the motor.
  • If you have multiple Dooya motors, ensure each is correctly paired to its designated channel (if using a multi-channel remote) or a dedicated single-channel remote to prevent unintended operation.

8. Warranty and Support

This Dooya DC1600 Single Channel Emitter is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and duration, please refer to the documentation provided with your purchase or contact your retailer.

Customer Support:

For technical assistance, troubleshooting, or warranty claims, please contact the seller or the official Dooya customer support channels. Have your product model number (DC1600) and purchase details ready when contacting support.

© 2024 Dooya. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.