EHEIM aquacompact 40/60 (2004/2005)

Contents

EHEIM aquacompact 40/60 External Filter Spare Parts Instruction Manual

Models: 2004 / 2005

Introduction

This manual provides detailed information regarding the spare parts for your EHEIM aquacompact 40 (Model 2004) and aquacompact 60 (Model 2005) external filters. It includes an overview of available parts, specifications, and general guidance for installation, operation, maintenance, and troubleshooting. Please refer to your main filter manual for complete instructions on the filter unit itself.

EHEIM aquacompact 40/60 External Filter Spare Parts Overview
Overview of EHEIM aquacompact 40/60 spare parts.

Product Overview: Spare Parts

The EHEIM aquacompact external filters are designed with modular components, allowing for easy replacement of individual parts. Below is an exploded view of the filter and a comprehensive list of available spare parts with their respective order numbers.

EHEIM aquacompact 40/60 Exploded View and Spare Parts List
Exploded view of EHEIM aquacompact filter with corresponding spare part numbers.

Detailed Spare Parts List

Order No.Spare Part
2616040Set of filter pads (2x blue, 3x white) for aquacompact 40 and 60 (type 2004 and 2005)
4009800Nozzle set, consisting of: jet nozzle, lower elbow connector, sleeve, wide jet outlet nozzle, outlet jet pipe, pipe plug
7218468Hose clamp (2 pieces)
7229698Sealing ring
7229868Silicon hose Ø 12/16 mm (2x 25 cm)
7312698Rubber feet (4 pieces)
7447150Set of pipe plugs
7481210Pump cover with screw
7481220Extension with inlet strainer
7481238Fastening clip (3 pieces)
7481240Filtermedia container for aquacompact 40 (type 2004)
7481250Filtermedia container for aquacompact 60 (type 2005)
7481268Filter container head
7635920Impeller (50 Hz)
7635930Impeller (60 Hz)

Individual Spare Part Visuals

  • Extension with suction basket, Order No: 7481220
    Extension with suction basket (Order No: 7481220)
  • Accessories kit, Order No: 350850
    Accessories kit (Order No: 350850)
  • Nozzle set components, Order No: 4009800
    Nozzle set components (Order No: 4009800)
  • Filter container head, Order No: 7481268
    Filter container head (Order No: 7481268)
  • Fastening clip, Order No: 7481238
    Fastening clip (Order No: 7481238)
  • Hose clamp, Order No: 7218468
    Hose clamp (Order No: 7218468)

Specifications

AttributeValue
Product TypeExternal Filter Spare Parts
Filter Modelsaquacompact 40 (Type 2004), aquacompact 60 (Type 2005)
Voltage220-240V (for compatible filter units)
ApplicationFish aquariums
OriginMainland China
Package Length10 cm
Package Width8 cm
Package Height10 cm
Package Weight0.5 kg

Setup and Installation of Spare Parts

When replacing any part of your EHEIM aquacompact filter, ensure the filter is disconnected from the power supply and removed from the aquarium. Follow these general steps:

  1. Disassembly: Carefully disassemble the filter unit according to your main filter manual. Note the position and orientation of each component.
  2. Part Identification: Identify the specific spare part you need to replace using the exploded view diagram and the order numbers provided in the Product Overview section.
  3. Replacement: Remove the old, damaged, or worn part. Install the new spare part, ensuring it fits securely and correctly. Pay close attention to seals (e.g., sealing ring, Order No: 7229698) to prevent leaks.
  4. Reassembly: Reassemble the filter unit in reverse order of disassembly. Double-check all connections, especially hoses and clamps (Order No: 7218468), to ensure they are tight and leak-proof.
  5. Testing: Before placing the filter back into operation, perform a leak test by filling the filter with water outside the aquarium and observing for any drips.

For specific component replacement, such as the impeller (Order No: 7635920/7635930) or filter container head (Order No: 7481268), refer to the detailed diagrams for correct placement.

Operating with New Spare Parts

Once new spare parts are installed and the filter is reassembled and leak-tested, you can resume normal operation. The EHEIM aquacompact filter operates by drawing water from the aquarium, passing it through various filter media, and returning clean water. Ensure proper water flow and check for any unusual noises or vibrations, which might indicate incorrect assembly or a faulty part.

  • Initial Start-up: After reassembly, prime the filter as per your main filter manual to ensure it fills with water and starts pumping correctly.
  • Flow Rate: Observe the water flow rate. A reduced flow rate might indicate blockages or an issue with the impeller or pump cover.
  • Noise Level: The filter should operate quietly. Excessive noise could be due to an improperly seated impeller or air trapped within the system.

Maintenance of Spare Parts

Regular maintenance of your filter and its components is crucial for optimal performance and longevity. This includes:

  • Filter Media Replacement: Replace filter pads (Order No: 2616040) regularly as recommended by EHEIM to maintain water quality. Rinse other filter media in old aquarium water to preserve beneficial bacteria.
  • Impeller Cleaning: Periodically inspect and clean the impeller (Order No: 7635920/7635930) and its shaft. Remove any debris or mineral buildup that could impede its rotation.
  • Seal Inspection: Check all sealing rings (Order No: 7229698) and O-rings for cracks, hardening, or deformation. Replace them if necessary to prevent leaks.
  • Hose and Connection Check: Inspect hoses (Order No: 7229868) and hose clamps (Order No: 7218468) for wear, kinks, or loose connections. Ensure all pipe plugs (Order No: 7447150) are securely in place.
  • Accessory Cleaning: Clean the extension with inlet strainer (Order No: 7481220) and nozzle set components (Order No: 4009800) to ensure unobstructed water intake and output.

Troubleshooting Common Issues

If you encounter problems after replacing spare parts, consider the following:

  • No Water Flow / Reduced Flow:
    • Check if the impeller (Order No: 7635920/7635930) is correctly installed and free of obstructions.
    • Ensure the pump cover (Order No: 7481210) is securely fastened.
    • Verify that hoses and inlet/outlet components (Order No: 7481220, 4009800) are not clogged or kinked.
    • Confirm the filter is properly primed and filled with water.
  • Leaks:
    • Inspect all sealing rings (Order No: 7229698) and O-rings for proper seating and damage. Replace if necessary.
    • Ensure hose clamps (Order No: 7218468) are tight and hoses (Order No: 7229868) are securely connected to the filter and aquarium.
    • Check the filter container head (Order No: 7481268) and fastening clips (Order No: 7481238) for secure closure.
  • Excessive Noise:
    • The impeller (Order No: 7635920/7635930) might be incorrectly installed or damaged. Inspect and reseat or replace.
    • Air trapped in the filter can cause noise. Tilt the filter gently to release air bubbles.
    • Ensure the filter is placed on a stable surface using the rubber feet (Order No: 7312698) to reduce vibration.

User Tips

  • Always keep a spare set of essential wear-and-tear parts, such as impellers and sealing rings, to minimize downtime in case of failure.
  • When replacing hoses, ensure you use the correct diameter (e.g., 12/16 mm for silicon hose, Order No: 7229868) to maintain proper flow and prevent leaks.
  • Regularly check the condition of all plastic components for brittleness or cracks, especially after prolonged use.

Warranty and Support

For specific warranty information regarding your EHEIM aquacompact filter and its spare parts, please refer to the documentation provided with your original filter purchase or contact the authorized EHEIM dealer or manufacturer directly. Keep your proof of purchase for any warranty claims.

If you require further technical assistance or have questions about specific spare parts, please reach out to EHEIM customer support or your product retailer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.