AKKO MOD001

Contents

Akko MOD001 CNC Mechanical Keyboard Kit Instruction Manual

Model: MOD001

Introduction

This manual provides comprehensive instructions for the assembly, operation, and maintenance of your Akko MOD001 CNC Mechanical Keyboard Kit. The MOD001 is an 80% form factor custom DIY kit featuring a programmable PCBA and hot-swappable Gateron sockets, allowing for personalized mechanical keyboard builds.

Akko MOD001 CNC Mechanical Keyboard Kit (Purple/Red)

Figure 1: Akko MOD001 CNC Mechanical Keyboard Kit (Purple/Red variant)

Package Contents

Please verify that all items are present in your package:

  • Aluminum Top Case (x1)
  • Plate (x1)
  • EVA Foam (x1)
  • PCBA (Printed Circuit Board Assembly) (x1)
  • Bottom Dampening Sheet (x1)
  • Aluminum Bottom Case (x1)
  • USB-A to USB-C Cable (x1)

Note: Keycaps and switches are NOT included in this kit and must be purchased separately.

Setup and Assembly

The Akko MOD001 kit is designed for easy assembly. Follow these steps to build your mechanical keyboard:

  1. Unpack Components: Carefully remove all components from the packaging.
  2. Prepare the PCBA: The PCBA is the main circuit board.
  3. Install Switches: The MOD001 features hot-swappable Gateron sockets. Align the pins of your chosen 3-pin or 5-pin mechanical switches with the holes on the PCBA and gently press them into place until they click. No soldering is required.
  4. Layer Assembly: The keyboard uses a sandwich mount structure. Assemble the layers in the following order from bottom to top:
    • Aluminum Bottom Case
    • Bottom Dampening Sheet
    • PCBA (with switches installed)
    • EVA Foam
    • Plate
    • Aluminum Top Case
    Ensure all components align correctly to prevent wobbling.
  5. Secure the Case: Fasten the top and bottom aluminum cases together using the provided screws (if any, typically included with the case).
  6. Attach Keycaps: Once switches are installed, press your desired keycaps onto the switches.
  7. Connect Cable: Connect the detachable USB-A to USB-C cable to the keyboard and your computer.
Exploded view of Akko MOD001 keyboard layers

Figure 2: Exploded view of keyboard layers: 1. Aluminum Top Case, 2. Plate, 3. EVA Foam, 4. PCBA, 5. Bottom Dampening Sheet, 6. Aluminum Bottom Case.

Close-up of hot-swappable Gateron sockets on PCBA

Figure 3: Hot-swappable Gateron sockets on the PCBA for easy switch installation.

Video 1: Unboxing and initial setup demonstration, including RGB lighting test.

Operating Instructions

RGB Backlight

The Akko MOD001 kit is equipped with North-facing RGB SMD lighting. Once connected to your computer, the RGB lighting should activate. Specific key combinations or software (if available from Akko) can be used to customize lighting effects, colors, and brightness. Refer to Akko's official website or support resources for detailed software instructions.

RGB backlight demonstration on Akko MOD001 keyboard without keycaps

Figure 4: RGB backlight in action, showcasing various colors on the keyboard without keycaps.

RGB backlight demonstration on Akko MOD001 keyboard with some switches installed

Figure 5: RGB backlight illuminating switches on the Akko MOD001.

Maintenance

To ensure the longevity and optimal performance of your Akko MOD001 keyboard kit, regular maintenance is recommended:

  • Cleaning: Use a soft brush or compressed air to remove dust and debris from between the keycaps and switches. For deeper cleaning, keycaps can be removed.
  • Switch Replacement: Thanks to the hot-swappable sockets, individual switches can be easily replaced without soldering. Use a switch puller tool to carefully remove a switch and insert a new one, ensuring the pins are straight and align with the socket.
  • Cable Care: Avoid sharp bends or excessive pulling on the USB-C cable to prevent damage.

Troubleshooting

If you encounter issues with your Akko MOD001 kit, try the following troubleshooting steps:

  • Keyboard Not Recognized:
    • Ensure the USB-C cable is securely connected to both the keyboard and your computer.
    • Try a different USB port on your computer.
    • Test with a different USB-C cable if available.
    • Restart your computer.
  • Keys Not Responding:
    • Carefully remove the keycap and then the switch for the non-responsive key.
    • Inspect the switch pins for any bends or damage. Straighten bent pins gently with tweezers.
    • Reinsert the switch firmly into the hot-swap socket.
    • Test with a known working switch in the same socket to rule out a PCBA issue.
  • RGB Lighting Issues:
    • Ensure the keyboard is properly connected.
    • Check if any software or key combinations are controlling the RGB.
    • Verify that the switches are installed correctly, as some RGB effects might depend on proper switch contact.

If problems persist, please contact Akko customer support for further assistance.

Specifications

FeatureDetail
ModelMOD001 CNC Mechanical Keyboard Kit
Layout87-Key (TKL - Tenkeyless)
Mounting StyleTray-mount (Sandwich Mount / Up-Down Structure)
Switch CompatibilityHot-swappable Gateron sockets, compatible with most North-facing 3-pin/5-pin mechanical switches (e.g., Cherry MX, Kailh, Gateron)
BacklightNorth-facing RGB SMD Backlit
ConnectivityDetachable USB-A to USB-C Cable
Case MaterialAluminum
Product Dimensions400mm (L) x 140mm (W)
WeightApprox. 2kg (total weight of assembled case)
DampeningDouble muffled foams (bottom, and between PCB/plate)
Akko MOD001 keyboard kit in Neon and Psittacus color variants with example keycap sets

Figure 6: Akko MOD001 kit shown with example keycap sets in Neon and Psittacus colorways. Note: Keycaps and switches are not included.

User Tips

Here are some general tips to enhance your experience with the Akko MOD001 kit:

  • Switch Selection: Experiment with different mechanical switches (linear, tactile, clicky) to find the typing feel that best suits your preference, taking advantage of the hot-swappable feature.
  • Keycap Customization: The standard layout allows for a wide variety of aftermarket keycap sets to personalize your keyboard's aesthetic.
  • Sound Customization: The included dampening foams significantly reduce hollow sounds. For further sound tuning, consider adding additional dampening materials or modifying stabilizers.
  • Software Customization: Check the official Akko website for any available software that allows for advanced key remapping, macro creation, and RGB lighting customization.

Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Akko website or contact the seller directly. Keep your proof of purchase for warranty claims.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.