Introduction
This manual provides essential information for the installation, operation, maintenance, and troubleshooting of your new FGHGF Vacuum Cleaner Wheel Motor Assembly. This replacement part is designed to restore optimal mobility to your compatible robot vacuum cleaner, ensuring efficient cleaning performance.

Compatibility
This wheel motor assembly is compatible with the following robot vacuum cleaner models:
- ZACO V5s Pro
- ILIFE V5s Pro
- ZACO V3s Pro
- ILIFE V3s Pro
- ZACO V5x
- ILIFE V5x
- ZACO V4
- ILIFE V4
Please ensure your robot vacuum cleaner model matches one of the listed compatible models before proceeding with installation.
Specifications
| Attribute | Value |
|---|---|
| Brand Name | FGHGF |
| Model Number | for ZACO v5s pro v3s pro V5x V4 |
| Material | Metal, ABS Plastic |
| Vacuum Part Type | Wheels |
| Type | Vacuum Cleaner Parts |
| Origin | Mainland China |

Installation Instructions
Replacing the wheel motor assembly requires basic tools and careful handling. Always ensure the robot vacuum is powered off and disconnected from its charging base before beginning.
- Power Off: Turn off your robot vacuum cleaner and disconnect it from any power source or charging dock.
- Access Wheels: Carefully flip the robot vacuum cleaner over to expose the underside where the wheels are located.
- Remove Bottom Cover (if applicable): Some models may have a bottom cover secured by screws that needs to be removed to access the wheel modules. Use a screwdriver to remove these screws and set the cover aside.
- Locate Wheel Module: Identify the wheel module that needs replacement. Each module typically consists of the wheel, motor, and housing.
- Remove Old Module: Unscrew any retaining screws holding the faulty wheel module in place. Gently disconnect any wiring harnesses connected to the module. Note the orientation of the wiring for reinstallation.
- Install New Module: Connect the wiring harness of the new FGHGF Wheel Motor Assembly to the corresponding port on the robot vacuum. Ensure the connection is secure.
- Secure New Module: Place the new wheel module into its designated slot and secure it with the retaining screws.
- Reassemble: Reattach the bottom cover (if removed) and secure it with its screws.
- Test Functionality: Flip the robot vacuum back to its upright position, power it on, and initiate a test cleaning cycle to ensure the new wheel motor functions correctly.

Caution: If you are unsure about any step, it is recommended to consult a professional or refer to your robot vacuum's specific service manual.
Operating the Wheel Motor Assembly
The FGHGF Wheel Motor Assembly is a component part of your robot vacuum cleaner. Once correctly installed, it operates automatically as part of the robot's navigation and cleaning system. There are no direct user controls for the wheel motor itself. Its function is to provide propulsion and steering for the robot vacuum, allowing it to move across various surfaces and navigate around obstacles.
Ensure that the robot vacuum's wheels are free from obstructions to allow the motor to operate efficiently.
Maintenance
Proper maintenance of your robot vacuum's wheels and motors can extend their lifespan and ensure consistent performance.
- Regular Cleaning: Periodically inspect the wheels and wheel wells for accumulated hair, dust, string, or other debris. Use a small brush or a pair of tweezers to carefully remove any obstructions.
- Check for Wear: Over time, the wheel treads may wear down. While the motor assembly itself is robust, excessive wear on the wheel's rubber can affect traction and navigation.
- Avoid Liquid Exposure: Do not expose the wheel motor assembly directly to water or cleaning solutions, as this can damage the internal electronic components and motor.
- Gentle Handling: When cleaning or handling the robot vacuum, avoid applying excessive force to the wheels, which could strain the motor or its mounting.
Troubleshooting
If your robot vacuum experiences issues related to movement after installing the new wheel motor, consider the following:
- Robot Not Moving:
- Ensure the wheel module is correctly installed and all screws are tightened.
- Verify that the wiring harness is securely connected to the robot's mainboard.
- Check for any debris or hair caught in the wheel mechanism that might be preventing movement.
- Uneven Movement or Turning in Circles:
- This could indicate an issue with one of the wheel motors. Ensure both left and right wheel motors are functioning properly.
- Re-check the installation of both wheel modules to ensure they are seated correctly and not obstructed.
- If only one wheel motor was replaced, ensure the other original wheel motor is also clean and functioning.
- Unusual Noise from Wheels:
- Inspect the wheel area for any foreign objects that might be causing friction or grinding sounds.
- Ensure the wheel module is properly seated and not loose.
If problems persist after troubleshooting, further inspection by a qualified technician may be necessary.
User Tips
- When replacing a single wheel motor, consider inspecting the other wheel motor for signs of wear or damage, as they often experience similar usage.
- Keep a small toolkit with appropriate screwdrivers handy for routine maintenance and part replacement.
- Regularly check the robot vacuum's app (if applicable) for error codes related to wheel or motor issues, which can help diagnose problems quickly.
Warranty and Support
For information regarding warranty coverage, returns, or technical support, please refer to the seller's policies or contact the seller directly through the platform where the purchase was made. Keep your purchase receipt or order number readily available when contacting support.