1. Introduction
The Garmin Speed Sensor 2 and Cadence Sensor 2 are wireless sensors designed to monitor your cycling performance. These easy-to-install sensors provide accurate speed, distance, and pedaling cadence data, which can be transmitted to compatible Garmin devices, cycling computers, and training apps via ANT+ and Bluetooth Low Energy technology. Their magnet-free design allows for simple installation, maintenance, and transfer between multiple bicycles.
2. Setup and Installation
The Garmin Speed Sensor 2 and Cadence Sensor 2 are designed for quick and easy installation without the need for magnets.
2.1 Cadence Sensor Installation
- Select the appropriate size rubber band for your crank arm.
- Place the cadence sensor on the inside of any crank arm.
- Secure the sensor firmly using the rubber band, ensuring it is stable and does not interfere with pedaling.
2.2 Speed Sensor Installation
- Select the appropriate size rubber band for your wheel hub.
- Place the speed sensor on the hub of either the front or rear wheel.
- Secure the sensor firmly using the rubber band, ensuring it is centered and stable on the hub.
2.3 Pairing with a Device
Once installed, the sensors will automatically begin transmitting data. To receive data, you need to pair them with a compatible device (e.g., Garmin Edge cycling computer, GPS watch, or smartphone app).
- Ensure your receiving device (e.g., Garmin Edge) is powered on and within range of the sensors.
- On your receiving device, navigate to the sensor pairing menu.
- Select to add a new speed sensor and a new cadence sensor. The sensors should appear in the list of available devices.
- Follow the on-screen prompts to complete the pairing process. The sensors will self-calibrate to provide accurate data.
The sensors support both ANT+ and Bluetooth Low Energy (BLE) for broad compatibility.
3. Operating the Sensors
After successful installation and pairing, the sensors operate automatically when you start cycling.
- Speed Sensor 2: Detects wheel rotation to calculate current speed and distance traveled. It provides accurate data even when GPS signal is unavailable (e.g., indoors or in tunnels).
- Cadence Sensor 2: Measures your pedaling rate in revolutions per minute (RPM), helping you maintain an efficient cadence for your training.
- Data Transmission: Both sensors continuously transmit data wirelessly via ANT+ and Bluetooth to your paired device.
4. Maintenance
The Garmin Speed and Cadence Sensors are designed for durability and low maintenance.
- Cleaning: Wipe the sensors with a damp cloth to remove dirt and debris. Avoid using harsh chemicals or abrasive cleaners.
- Battery Replacement: The sensors use a replaceable coin cell battery (CR2032). When the battery is low, your paired device may indicate a low battery warning. To replace:
- Carefully remove the sensor from its mounting.
- Use a small coin to twist open the battery cover on the back of the sensor.
- Remove the old battery and insert a new CR2032 battery with the positive (+) side facing up.
- Replace the battery cover and twist to secure it.
- Re-install the sensor on your bike.
- Storage: If storing the bike or sensors for an extended period, consider removing the batteries to prevent drainage.
5. Troubleshooting
- Sensor Not Detected:
- Ensure the sensors are correctly installed and the bike is in motion (for speed sensor) or pedals are turning (for cadence sensor) to activate them.
- Check the battery. Replace if necessary.
- Ensure your receiving device's ANT+ or Bluetooth is enabled and it's within range.
- Try re-pairing the sensors with your device.
- Inaccurate Readings:
- Verify the sensors are securely mounted and not shifting during use.
- For speed sensor, ensure your wheel size is correctly configured on your receiving device, if applicable. The sensor self-calibrates, but manual input can sometimes override or assist.
- Ensure no strong electromagnetic interference sources are nearby.
- Connectivity Issues:
- Move closer to your receiving device.
- Ensure no other devices are interfering with the ANT+ or Bluetooth signal.
- Restart both the sensors (by removing and reinserting the battery) and your receiving device.
6. Specifications
| Feature | Detail |
|---|---|
| Brand | Garmin |
| Model | Speed Sensor 2, Cadence Sensor 2 |
| Connectivity | ANT+, Bluetooth Low Energy (BLE) |
| Sensor Type | Magnet-free speed and cadence sensors |
| Speed Sensor Mounting | Wheel hub |
| Cadence Sensor Mounting | Crank arm |
| Battery Type | CR2032 (user-replaceable) |
| Function | Passometer, Remote Control |
| Language | English (for associated software/manuals) |
7. User Tips
- For optimal accuracy, ensure sensors are mounted securely and do not rotate or shift during your ride.
- When using with multiple bikes, the easy-to-move design allows for quick transfer. Remember to re-pair if switching to a different head unit.
- Keep the sensor firmware updated through your Garmin device or Garmin Connect app for best performance and new features.
- If you experience intermittent data, check for potential obstructions or interference between the sensor and your receiving device.
8. Warranty and Support
Garmin products are typically covered by a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or visit the official Garmin support website. For technical assistance, troubleshooting, or service inquiries, please contact Garmin customer support directly.