1. Introduction
Thank you for purchasing the CORONA C4SF-HV 2.4GHz S-FHSS/FHSS compatible receiver. This product is designed to provide enhanced, smooth control when used with FUTABA S-FHSS/FHSS link systems. Please read this manual thoroughly before operation to ensure proper setup and safe use.

2. Features
- 4-channel servo output in normal operating status.
- S.BUS output support for expanding servo channels on the 4th channel when in special status.
- Waterproof function for enhanced durability.
3. Specifications
| Parameter | Value |
|---|---|
| Operating Current | 60mA max (45mA under linked status) |
| Operating Voltage | 3.6V ~ 8.5V |
| Sensitivity | About -95dBm |
| Operation Temperature | -10°C ~ 70°C |
| Weight | 11g (actual measured weight may be 6.3g) |
| Latency | 13.6mS or 20.4mS |
| Size | 34mm * 22mm * 10mm |
| Material | Composite Material |
| Recommended Age | 14+ years |
| For Vehicle Type | Airplanes |
| RC Parts & Accs | Receivers |

4. Setup
4.1. Compatibility
The CORONA 2.4GHz S-FHSS/FHSS Compatible Receiver is designed for use with FUTABA S-FHSS/FHSS 2.4GHz transmitters. This includes air systems such as T4YF, T6J, T6K, T8J, T10J, T14SG, T18MZ, T18SZ, and surface systems like 3PL, T3PRKA, 4PLS, T4PX, T4GRS, operating under S-FHSS/FHSS protocol mode.
4.2. Bind Procedure
- Turn on your S-FHSS/FHSS transmitter. Keep it approximately 0.5 to 1 meter away from the receiver.
- While pressing the F/S (Failsafe) button on the receiver, connect the battery to the receiver.
- The receiver's Red LED will light up, and the Green LED will be off, indicating it is searching for signals.
- Once binding is successful, the Green LED will light up, and the Red LED will turn off.

5. Operating Instructions
5.1. Failsafe Setting
Set the failsafe feature on your S-FHSS/FHSS transmitter, similar to how you would operate with other FUTABA receivers, if this feature is available on your transmitter. It is highly recommended to set a failsafe feature when operating your models. A common and useful failsafe setting is to shut down the model's throttle, preventing it from flying or driving away uncontrolled in case of signal loss.
5.2. Special/Normal Mode Switch Guide
If your receiver has already been linked with your transmitter, follow these steps to switch between Special and Normal modes:
- Power off your transmitter.
- When the receiver's LED light is red, push and hold the button on your receiver for more than 6 seconds but less than 10 seconds.
- Release the button. The green LED will flash.
- Push the button again immediately. The receiver will return to a solid red light.
- The MODE status has now changed.
- A slow green LED flash indicates a switch from Normal mode to Special mode.
- A fast green LED flash indicates a switch from Special mode to Normal mode.
In Special mode, the S.BUS output feature is available on the 4th servo channel. Other channels remain unchanged.
5.3. Servo Selection Guide
If you intend to use analog servos with your model, ensure the receiver is operating in Normal mode.
5.4. LED Status Table
| RED LED | GREEN LED | Status |
|---|---|---|
| ON | off | No signal searched |
| OFF | solid | Signal is very good |
| OFF | flash | Signal is not very good |
| OFF | off-flash | Signal is weak |

6. User Tips
- Transmitter Compatibility: Always double-check your specific Futaba transmitter model (e.g., T4PM) against the listed compatible models to ensure full functionality and avoid issues.
- Failsafe Importance: Do not skip setting up the failsafe feature. It is a critical safety measure for your model.
- Mode Switching: When switching between Special and Normal modes, ensure your transmitter is powered off to prevent accidental control inputs during the process.
7. Troubleshooting
7.1. Binding Issues
- Receiver not binding: Ensure your transmitter is within 0.5-1 meter of the receiver during the binding process. Verify that you are pressing the F/S button on the receiver while connecting power.
- LEDs not indicating successful bind: If the Red LED remains ON and Green LED OFF, the receiver is still searching for a signal. Re-check transmitter power and proximity. If the Green LED flashes, refer to the LED Status Table for signal quality.
7.2. Signal Issues
- Weak or no signal: Refer to the LED Status Table (Section 5.4) to diagnose signal quality. Check antenna placement on both receiver and transmitter. Ensure no obstructions or interference sources are nearby.
- Intermittent control: This could indicate a weak signal (Green LED flashing). Check battery levels on both transmitter and receiver.
7.3. Servo Functionality
- Analog servos not working correctly: Ensure the receiver is in Normal mode if you are using analog servos (refer to Section 5.2 for mode switching).
- S.BUS output not active: Verify the receiver is in Special mode if you intend to use the S.BUS output on the 4th channel.
8. Maintenance
- Keep the receiver clean and free from dust and debris.
- Avoid exposing the receiver to extreme temperatures or direct sunlight for prolonged periods.
- While the receiver has a waterproof function, it is not designed for submersion. Avoid direct contact with water where possible.
- Regularly inspect all connections and wiring for any signs of wear or damage.
9. Warranty and Support
For any technical assistance or warranty inquiries, please contact the retailer or manufacturer directly. Keep your proof of purchase for warranty claims.