1. Introduction
Thank you for choosing the Kunray E-bike Motor Bike Display. This universal LCD speedometer is designed for electric scooters and bikes operating on 48V to 72V systems, providing essential riding data at a glance. This manual provides detailed instructions for installation, operation, and maintenance to ensure safe and optimal performance of your display.
2. Safety Information
⚠ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
- Ensure the display is installed by a qualified technician if you are unsure about the wiring process.
- Always disconnect power before performing any installation or maintenance.
- Do not attempt to modify the display or its wiring, as this may cause damage or injury.
- Keep the display clean and dry. Refer to the maintenance section for waterproofing details.
3. Package Contents
Verify that all items are present in your package:
- Kunray E-bike Motor Bike Display
- Wiring Harness
- Mounting Bracket
- Mounting Nuts
4. Specifications
| Feature | Description |
|---|---|
| Type | Display |
| Voltage Compatibility | 48V-72V Universal |
| Display Type | LCD Color Display |
| Speed Measurement | Phase Hall Sensor (requires compatible controller) |
| Dimensions (L x W) | 150mm x 85mm |
| Cable Length | 300mm |
| Weight | 220g |
| Mounting Hole Distance | 70mm |
| Waterproof Rating | IP54 |
5. Setup & Installation
Follow these steps to install your Kunray E-bike Motor Bike Display:
- Mounting: Secure the display to your e-bike's handlebar using the provided mounting bracket and nuts. Ensure it is positioned for clear visibility and does not obstruct your riding.
- Wiring Connection: Carefully connect the display's wiring harness to your e-bike's controller and power supply according to the diagram below.
Wiring Diagram and Function Description:
- Red Wire: Positive pole - Connect to the positive pole of the power supply.
- Green Wire: Negative pole - Connect to the negative pole of the power supply.
- Purple Wire (Instrument/Speed Line): Connect to the instrument line of your controller.
- Orange Wire: Turn left signal - Connect to the steering switch.
- Light Blue Wire: Turn right signal - Connect to the steering switch.
- Dark Blue Wire: Headlights - Connect to the headlight switch.
Important Note on Speed Measurement: The display uses phase hall sensor for speed measurement. Ensure your controller is a phase controller for proper speed display. For one-wire communication, the original vehicle instrument is connected to the yellow line for speed measurement on the first line. If not, this connection will not be used.
Voltage Connection: For 48V-72V systems, ensure the appropriate voltage connection. If your system is 60V, connect the designated 60V line; otherwise, disconnect it for 48V/72V systems.
6. Operating Instructions
Once installed and powered on, the display will show various riding data. Refer to the diagram below for an explanation of each indicator:
- Turn Left Indicator: Illuminates when the left turn signal is active.
- Speed: Displays current riding speed in km/h.
- Headlight Indicator: Illuminates when the headlights are on.
- Turn Right Indicator: Illuminates when the right turn signal is active.
- Battery Indicator: Shows the current battery charge level.
- Voltage: Displays the current system voltage.
- Mileage: Shows the total distance traveled.
The display provides clear and visible riding data, enhancing your e-bike experience.
7. Maintenance
- Cleaning: Wipe the display screen with a soft, damp cloth. Avoid using abrasive cleaners or solvents.
- Waterproofing: The display has an IP54 waterproof rating, meaning it is protected against dust and splashing water. When using it in rainy days, please don't soak it in water and wipe it dry in time after use to prevent damage.
- Storage: Store the display in a dry, cool place when not in use for extended periods.
- Wiring Inspection: Periodically check all wiring connections to ensure they are secure and free from corrosion or damage.
8. Troubleshooting
If you encounter issues with your display, refer to the following common problems and solutions:
- Display Not Turning On:
- Check all power connections (Red and Green wires) to ensure they are securely connected to the correct poles of your power supply.
- Verify that your e-bike's battery has sufficient charge.
- Ensure the voltage of your e-bike system (48V-72V) matches the display's compatibility.
- Incorrect Speed Reading:
- Confirm that your e-bike's controller is a phase controller, as the display relies on this for speed measurement.
- Check the Purple (Instrument/Speed) wire connection to your controller.
- If using one-wire communication, ensure the yellow line is correctly connected to the original vehicle instrument.
- Turn Signals or Headlight Indicator Not Working:
- Check the Orange (turn left), Light Blue (turn right), and Dark Blue (headlight) wire connections to their respective switches.
- Ensure the turn signals and headlights themselves are functioning correctly.
- Inaccurate Battery/Voltage Reading:
- Verify the main power connections (Red and Green wires) are stable.
- Ensure the display is correctly configured for your system's voltage (48V, 60V, or 72V).
If the problem persists after checking these points, please consult the official user manual PDF or contact customer support.
9. User Tips
- Programming: Based on common user inquiries, this display is generally designed for plug-and-play functionality with compatible controllers and does not typically feature advanced user-programmable settings. Its primary function is to display real-time riding data.
- Visibility: For optimal visibility, especially in bright sunlight, ensure the display is angled correctly during installation.
- PDF Manual: For more detailed guides and specific technical information, please refer to the comprehensive user manual available in PDF format.
10. Warranty & Support
For specific warranty information and customer support, please refer to the documentation provided at the time of purchase or contact the seller directly. If you have any problems with your order, please contact us first before leaving feedback.
You can also consult the official user manual (PDF) for additional information: View User Manual (PDF)
11. Manufacturing Process
The Kunray E-bike Motor Bike Display undergoes a rigorous manufacturing process to ensure quality and reliability. This includes automated assembly of circuit boards and thorough testing before packaging.