1. Product Overview
The T.SK105A.03 is a versatile universal LCD LED TV controller driver board designed to support analog TV signals and various display equipment ranging from 15 to 42 inches. It features VGA, HDMI, and USB inputs, making it suitable for a wide range of applications. This manual provides essential instructions for its setup, operation, and maintenance.
2. Setup Instructions
2.1. Firmware Update
- Prepare a USB flash drive.
- Obtain the correct firmware file (e.g.,
UTS6710_03F_100.bin) from the seller, matching your screen resolution. Copy this.binfile directly to the root directory of the USB flash drive. Note that the exact filename may vary due to manufacturer updates, but the process remains the same. - Set the correct voltage on the board (3.3V/5V/12V) according to your screen's input voltage requirements. This is typically done via a jumper on the board.
- Plug the USB drive into the board's USB port. Connect the 7-key button board to the controller board.
- Plug in the power adapter (12V4A recommended) to power on the board. The light on the key board will start flashing, indicating that the program is being installed. Do not disconnect power during this process.
- After a few minutes, the LED will stop flashing, signifying completion. Power off the board, remove the USB drive, and then connect the LVDS cable and inverter (if required by your panel).
- Power on the board again. The screen should display "no signal", indicating successful firmware installation.
2.2. Physical Connections
Ensure all connections are secure and correctly oriented. Refer to the diagram below for port identification.
- DC12V: Power input.
- VGA: Video Graphics Array input.
- HDMI-I: High-Definition Multimedia Interface input.
- AV: Audio/Video composite input.
- Audio: Audio input/output.
- USB: Universal Serial Bus port for firmware updates and media playback.
- TV: Antenna input for analog TV signals.
- Backlight: Connector for display backlight.
- Keyboard: Connector for the 7-key button board.
- LVDS: Low-Voltage Differential Signaling connector for the display panel.
- Speaker: Audio output for speakers.
Ensure the LVDS cable and inverter are selected according to your specific panel specifications. If unsure, contact the seller with your panel number for assistance.
3. Operating Instructions
3.1. Remote Control Functions
The included remote control provides full functionality for navigating the TV board's menu and controlling various settings.
- Power Button: Turns the TV board on/off.
- Input/Source: Selects between VGA, HDMI, AV, and TV inputs.
- Menu: Accesses the on-screen display (OSD) menu for settings.
- Navigation Buttons (Up/Down/Left/Right/Enter): Used to navigate through menu options and confirm selections.
- Volume (+/-): Adjusts audio volume.
- Channel (+/-): Changes TV channels in analog TV mode.
- Display (DISP): Shows current input information.
- Sleep: Sets a sleep timer.
- Zoom: Adjusts screen zoom level.
3.2. Basic Operation
- Power On/Off: Press the red power button on the remote control or the power button on the 7-key board.
- Input Selection: Press the 'INPUT' button on the remote to cycle through available video sources (VGA, HDMI, AV, TV).
- Menu Navigation: Press the 'MENU' button to open the OSD. Use the arrow keys to navigate and 'ENTER' to select options. 'EXIT' returns to the previous menu or closes the OSD.
- Media Playback (via USB): Insert a USB drive containing compatible media files into the USB port. Use the remote to navigate to the media player function and select your desired content.
4. Maintenance
- Cleaning: Clean the board with a soft, dry cloth when it is dirty. Avoid using liquids or abrasive materials.
- Inspection: Periodically check the board for any visible defects such as damaged components or weighty nicks.
- Environment: Keep the board in a clean, dry environment, away from excessive heat, moisture, and direct sunlight.
5. Troubleshooting
- "No Signal" Message: If you see "no signal" after a firmware update, ensure the USB drive was removed after the update, and the LVDS cable and inverter (if applicable) are correctly connected to your panel. Also, verify the input source is correctly selected.
- Screen Line Issues or Dislocation: Ensure the screen line (LVDS cable) is not reversed or dislocated. Incorrect connection can cause display anomalies.
- Screen Changes Color / Display Anomalies: This could indicate an incorrect voltage setting for your panel or an issue with the LVDS cable connection. Double-check the voltage jumper setting (3.3V/5V/12V) and ensure the LVDS cable is securely connected and not damaged. If the issue persists, try resetting the board to factory settings via the OSD menu.
- Board Not Powering On: Verify the power adapter meets the requirement of 12V4A. Check all power connections.
- Firmware Update Failure: Ensure the USB drive is formatted correctly (FAT32 is common) and contains only the correct
.binfirmware file. Do not interrupt power during the update process.
6. Specifications
| Feature | Specification |
|---|---|
| Model Number | T.SK105A.03 (V53BJK1) |
| Brand Name | ETAxopowo |
| Compatible Equipment Style | Display Equipment |
| Supported Screen Size | 15-42 inch |
| Inputs | VGA, HDMI, AV, USB, TV (Analog) |
| Power Requirement | DC 12V, 4A (recommended) |
| Dimensions (WxHxD) | 20 x 14 x 4 cm (approximate package dimensions) |
| Origin | Mainland China |
| Certification | NONE |
7. User Tips
- Menu Access: If you encounter difficulty accessing the menu or if the screen cycles through colors, ensure all cables are firmly connected and the correct input source is selected. A quick power cycle (unplugging and replugging the power adapter) can sometimes resolve temporary display glitches.
- Panel Compatibility: Always confirm the compatibility of your display panel with the board, especially regarding LVDS cable type and inverter requirements. Incorrect connections can damage the board or panel.
- Static Electricity: Handle the board with care, especially in dry environments, to protect it from static electricity which can damage integrated circuits (ICs).
8. Warranty and Support
For technical support, firmware downloads, or assistance with panel compatibility, please contact the seller directly. Provide your panel number if you need help selecting the correct LVDS cable or inverter.
General Precautions:
- Protect the board from static electricity to avoid damage to the IC.
- Keep the board away from conductors when it is working.
- Do not press, distort, or disassemble the board.
- Do not switch on the power supply before the panel is correctly connected.
- The brightness of the panel is influenced greatly by temperature; measure it after power on for 10-30 minutes.
- Keep the board surface clean. Check the appearance of the board for any defective parts, such as damage or weighty nicks.