1. Introduction
The Douk Audio T4 PLUS is a versatile vacuum tube phono stage preamp, stereo audio preamp, and headphone amplifier designed for home audio systems. It features MM/MC phono input with adjustable impedance, a 3.5mm AUX input, and a built-in VU meter for visual feedback. Equipped with 6CS6 vacuum tubes (replaceable for sound-shaping), it delivers a warm, detailed, and dynamic sound. The T4 PLUS also includes a 3.5mm headphone output capable of driving 32-300 ohm headphones, making it an all-in-one solution for audiophiles.
This manual provides detailed instructions for setting up, operating, and maintaining your T4 PLUS to ensure optimal performance and longevity.

Figure 1: Douk Audio T4 PLUS Tube Preamp
2. Packing List
Please check the contents of your package. If any items are missing or damaged, contact customer support.
- 1x T4 PLUS Preamp
- 2x 6CS6 Vacuum Tube
- 1x DC 12V Power Adapter
- 1x 3.5mm to RCA Cable

Figure 2: Package Contents
3. Product Overview
Familiarize yourself with the controls and connections of your T4 PLUS unit.

Figure 3: T4 PLUS Front and Rear Panel
- VU meter
- Power switch/Volume knob (Anti-clockwise rotate to off/Vol-; Clockwise rotate to on/Vol+)
- 3.5mm Headphone output
- MM/MC switch; MC mode impedance setting
- PHONO GND interface
- PHONO input (red: right channel; white: left channel)
- Aux input
- RCA output interface (red: right channel; white: left channel)
- Power interface (DC 12V/1.5A (5.5*2.1mm))
- VU meter sensitivity regulator
4. Setup Instructions
Follow these steps to set up your Douk Audio T4 PLUS:
- Insert Vacuum Tubes: Carefully insert the provided 6CS6 vacuum tubes into the sockets on the T4 PLUS. Ensure the pins are not bent or deformed before insertion.
- Connect Audio Outputs: Connect your active speakers or an amplifier to the RCA output (8) of the T4 PLUS. Alternatively, you can connect headphones to the 3.5mm headphone output (3). Both stereo RCA and 3.5mm headphone jack can output audio simultaneously.
- Connect Audio Inputs:
- PHONO IN: Connect your turntable to the PHONO input (6) of the T4 PLUS. Use the MM/MC switch (4) to select the appropriate mode (MM for Moving Magnet, MC for Moving Coil) and adjust the matching impedance using the dip switches. Connect the turntable's ground wire to the PHONO GND interface (5) if available.
- AUX IN: Connect your audio source (e.g., phone, tablet, PC, MP3 player) to the 3.5mm AUX input (7). Note that the AUX input has priority; if an AUX cable is connected, the PHONO input will be bypassed. Ensure the AUX cable is unplugged if you intend to use the PHONO input.
- Connect Power: Connect the DC 12V power adapter to the power interface (9) on the T4 PLUS, then plug the power cable into a wall socket.
- Power On and Enjoy: Rotate the Power switch/Volume knob (2) clockwise to power on the unit. Adjust the volume to your preference and enjoy your music.
- Power Off: After use, rotate the Power switch/Volume knob (2) anti-clockwise to power off the unit, then disconnect the power adapter.

Figure 4: Connection Diagram
5. Operating Instructions
5.1 Input Selection
The T4 PLUS automatically prioritizes the 3.5mm AUX input. If you wish to use the MM/MC phono input, ensure no cable is connected to the AUX input. Use the MM/MC switch (4) to select the correct phono cartridge type and adjust impedance settings as needed.
5.2 Volume Control
The main knob (2) controls the volume for both the RCA line output and the 3.5mm headphone output simultaneously.
5.3 VU Meter Adjustment
The T4 PLUS features a VU meter adjustment (10) on the side panel. This allows you to fine-tune its sensitivity to match different input signals, achieving better visual effects and accurate level indication.

Figure 5: T4 PLUS Detailed View
5.4 Tube Rolling
The T4 PLUS comes with a pluggable tube socket, allowing for 'tube rolling' – replacing the default 6CS6 tubes with other compatible types to alter the sound signature to your preference. Compatible tubes include: 6J1, 6J2, 6J3, 6J4, 6J5, 6K4, 6*1N, 6*4N, 6*5N, 5725, 6AK5, EF95, 6BA6, 403B, etc. Always ensure the unit is powered off and unplugged before replacing tubes.

Figure 6: Vacuum Tubes
5.5 Visual Experience
The integrated VU meter provides a dynamic visual representation of your audio levels, enhancing the vintage aesthetic and overall enjoyment of your HiFi music experience.

Figure 7: VU Meter in Action
5.6 Product Demonstration Video
Video 1: Douk Audio T4 PLUS Product Demonstration
A short video demonstrating the Douk Audio T4 PLUS Tube Preamp, showing its connections and the VU meter in operation.
6. Specifications
| Feature | Specification |
|---|---|
| Brand | Douk Audio |
| Model | T4 PLUS |
| Audio Input | MM Phono/Turntable, 3.5mm AUX |
| Audio Output | Stereo L/R RCA, 3.5mm Headphone Jack |
| Max Headphone Output Power | 150mW @32Ω |
| Matched Headphone Impedance | 32-300Ω |
| Working Voltage | DC 12V/1.5A (5.5*2.1mm) |
| AUX Input Level | 0.775V |
| AUX RCA Max Output Level | 1.5V |
| AUX Frequency Response | 20Hz-20KHz (±0.3dB) |
| AUX S/N Ratio | ≥110dB |
| AUX THD | 0.2% |
| Phono Input Level | 0.005V |
| Phono RCA Max Output Level | 300mV (MM) / 3V (MC) |
| Phono Frequency Response | Conforms to RIAA characteristics (±3dB) |
| Phono S/N Ratio | 71dB |
| Phono THD | 0.8% |
| Dimensions (W*D*H) | 50*137*146mm / 1.97*5.39*5.75in |
| Net Weight | 640g / 1.41lb |
| Package Weight | 1000g / 2.20lb |
For more detailed specifications, please refer to the official user manual PDF: Douk Audio T4 PLUS User Manual (PDF)
7. Troubleshooting (FAQ)
- Q: Why are all cables connected but there is no sound?
- A: 1. Check the LED below the tubes: If it lights up normally, ensure the corresponding input mode is selected. If it doesn't light up, try another DC 12V power supply. 2. If the indicator light is on but no sound, check the audio signal transmission chain: audio source → audio cable → preamp/decoder → amplifier → speaker. 3. Confirm the audio source is not muted, paused, or has very low volume.
- Q: Why is the sound distorted?
- A: This may be due to excessive input amplitude. If both the audio source and T4 PLUS volumes are maxed out, distortion can occur. Reduce the volume of either the audio source or the T4 PLUS. Generally, set the amplifier volume to about 60% and fine-tune with the preamp.
- Q: Why is there a loud current sound or buzzing sound on the speaker?
- A: 1. Use the original power supply, as many third-party power supplies can cause interference. 2. Use shielded signal cables, especially when no load is connected, to prevent interface signals. 3. If noise persists, disconnect all inputs, leaving only power. If the noise disappears, it's from the audio input; if it remains, it may be the power supply or an internal product issue.
- Q: Why is there no sound output when using MC or MM mode?
- A: The AUX input has priority. Ensure the AUX input cable is unplugged, otherwise, the phono input will not produce sound.
- Q: Why is there a thumping sound when switching on/off?
- A: Ensure the correct on/off sequence. When turning on, follow the signal path: audio source → preamp/DAC → amplifier → speaker. When turning off, reverse the sequence. Turning off the preamp first can cause an impact sound that may damage the amplifier or speakers.
- Q: Why is the sound not clear every time the vacuum tube preamp starts to be used?
- A: Vacuum tubes are sensitive components that require a warm-up period to reach normal working status. It is generally recommended to warm up for about 15 minutes for optimal performance.
- Q: Why is there a faint sound even when the volume is turned up to the maximum without vacuum tubes?
- A: The preamp is designed for audio signal amplification. Even without vacuum tubes, other components can still produce weak signal coupling. Always install the vacuum tubes correctly before use.
- Q: Why is the sound from the headphone distorted after connecting to the headphone amplifier?
- A: Confirm the volume levels of both the audio source and the headphone amplifier. If the volume is too high and exceeds the headphone's power handling capacity, distortion will occur.
- Q: What is the difference between MM/MC? How to determine which type of phono cartridge it is?
- A: MM stands for Moving-Magnetic cartridge; MC stands for Moving-Coil cartridge. You can check your turntable's product model or specifications to determine the cartridge type. MM cartridges are commonly used in most modern record players.
- Q: What is RIAA?
- A: RIAA is a unified standard for the recording and playback of vinyl records, issued by the Recording Industry Association of America. Most phonographs and vinyl records produced today adhere to this standard.
- Q: What is the function of the phonograph GND? Why are not all phonographs grounded?
- A: The PHONO GND (Ground) connects the phono cartridge or turntable shell to the preamp's signal ground. This helps prevent inductive loads (like phono motors) from interfering with audio signals. Older turntables often have a dedicated GND wire or terminal, while newer ones might integrate the GND wire directly into the signal cable's negative pole.
8. User Tips
- Minimize Noise: To reduce potential current or buzzing sounds, always use shielded signal cables and ensure proper grounding for your turntable.
- Volume Balance: If you experience slight channel imbalance at very low volumes, especially with high-sensitivity headphones or speakers, try reducing the source volume and increasing the T4 PLUS volume. An impedance adapter can also help with headphones.
- Tube Warm-up: Allow your T4 PLUS about 15 minutes to warm up after powering on for the best sound clarity and performance from the vacuum tubes.
9. Safety Warnings
Failure to follow these warnings may result in injury, damage to the device, or voiding of the warranty.
- Do not open the shell of the T4 PLUS yourself. Improper operation may cause a risk of electric shock.
- Use only the original or a regular manufacturer's switching power supply. Using an incompatible power supply risks damage to the T4 PLUS.
- Do not use the T4 PLUS in high temperature or high humidity environments.
- Never unplug or plug in vacuum tubes while the T4 PLUS is powered on, as this can damage the tubes or the unit.
- Do not replace tubes with mismatched models. This can damage both the tubes and the T4 PLUS.
- The T4 PLUS is designed for a 12V power supply. Do not use a voltage exceeding 12V, as this will damage the unit.
- Keep the vacuum tube device as far away as possible from RF interference or electromagnetic interference sources and avoid vibration.
- Ensure adequate ventilation and heat dissipation around the vacuum tubes, as they generate heat during operation.
10. Warranty & Support
For technical support, warranty inquiries, or any questions regarding your Douk Audio T4 PLUS, please contact us through the following channels:
- Website: www.doukaudio.com
- Email: nobsound@doukaudio.com
- WeChat/Whatsapp: +86-17704028602
- Address: Room A304, Chunenghui, Digital Economy Industrial Base, No. 9, Baoye Road, Guanhu Street, Longhua District, Shenzhen, Guangdong
DOUK AUDIO - MAKE HI-FI AFFORDABLE