NISSEI RS-402

Contents

NISSEI RS-402 SWR Watt Meter User Manual

Model: RS-402

1. Introduction

The NISSEI RS-402 is a high-quality SWR & Power Meter designed for mobile radio communication. It provides accurate measurements of Forward (FWD) power, Reflected (REF) power, and Standing Wave Ratio (SWR) across a frequency range of 125-525MHz, with a power handling capability of up to 200W. This manual provides essential information for the proper setup, operation, and maintenance of your RS-402 meter.

2. Safety Information

  • Always ensure the device is connected to a stable 13.8V DC power source.
  • Do not exceed the maximum power rating of 200W to prevent damage to the meter.
  • Ensure all connections (TX, ANT) are secure before transmitting. Loose connections can lead to inaccurate readings or equipment damage.
  • Avoid operating the meter in wet or excessively humid environments.
  • Do not attempt to open the casing or modify the internal circuitry, as this will void the warranty and may cause electric shock or damage.

3. Package Contents

Upon unpacking, please verify that all the following items are included:

  • 1 x NISSEI RS-402 SWR & Power Meter
  • 1 x Operation Manual (this document)
  • 1 x 13.8V DC Power Wire
NISSEI RS-402 SWR Watt Meter with included manual and DC power cable
Image: NISSEI RS-402 SWR Watt Meter with included manual and DC power cable.

4. Specifications

FeatureSpecification
Frequency Range125-525MHz
Power Range1-200W
Power Scale5W / 20W / 200W
Maximum Power200W
Accuracy (5W range)(AVG) +/-10%; (REP) +/-15%
Accuracy (20-200W range)(AVG) +/-5%; (REP) +/-10%
Maximum Power for SWR3W
Input/Output ConnectorsM or N type (SO-239)
Net Weight800g
Insertion LossLess than 0.1dB
Testing FunctionFWD/REF POWER, REP, SWR
Input/Output Impedance50 Ohm
Size (W*H*D)190 x 85 x 135mm
CertificationCE, FCC, RoHS

5. Product Overview

5.1 Front Panel Controls

Front view of NISSEI RS-402 SWR Watt Meter showing dial, function knob, range knob, PEP button, AVG/SSB switch, and CAL knob.
Image: Front view of NISSEI RS-402 SWR Watt Meter.
  • S.W.R & Power Meter Dial: Displays SWR and power readings.
  • FUNCTION Knob (REF, FWD, SWR): Selects the measurement mode.
    • FWD: Measures forward power.
    • REF: Measures reflected power.
    • SWR: Measures Standing Wave Ratio.
  • RANGE Knob (5W, 20W, 200W): Selects the maximum power range for measurement.
  • PEP Button: Press to measure Peak Envelope Power (PEP).
  • AVG/SSB Switch: Toggles between Average power measurement and SSB (Single Sideband) mode for PEP measurement.
  • CAL Knob (MIN, MAX): Used for calibration in SWR mode.

5.2 Rear Panel Connectors

Rear view of NISSEI RS-402 SWR Watt Meter showing TX, ANT, and DC 13.8V connectors.
Image: Rear view of NISSEI RS-402 SWR Watt Meter.
  • TX Connector (SO-239): Connects to your radio's antenna output.
  • ANT Connector (SO-239): Connects to your antenna.
  • DC 13.8V Input: Power input for the meter.

6. Setup

Follow these steps to properly set up your NISSEI RS-402 SWR Watt Meter:

  1. Connect Power: Connect the supplied 13.8V DC power wire to the 'DC 13.8V' input on the rear panel of the meter. Connect the other end to a suitable 13.8V DC power supply.
  2. Connect Radio: Connect the antenna output of your radio to the 'TX' connector on the rear panel of the meter using a suitable coaxial cable.
  3. Connect Antenna: Connect your antenna to the 'ANT' connector on the rear panel of the meter using a suitable coaxial cable.
Video: A brief demonstration of the NISSEI RS-402 SWR Watt Meter in operation, showing its functionality and display.

7. Operating Instructions

To measure SWR and power, follow these steps:

  1. Power On: Ensure the meter is powered on via the 13.8V DC input.
  2. Select Power Range: Turn the RANGE knob to select the appropriate power range (5W, 20W, or 200W) that is higher than your radio's output power.
  3. Measure Forward Power (FWD):
    • Set the FUNCTION knob to FWD.
    • Transmit a continuous carrier (e.g., by pressing the PTT button on your radio).
    • Read the forward power directly from the meter's dial.
  4. Measure Reflected Power (REF):
    • Set the FUNCTION knob to REF.
    • Transmit a continuous carrier.
    • Read the reflected power directly from the meter's dial.
  5. Measure SWR:
    • Set the FUNCTION knob to FWD.
    • Transmit a continuous carrier.
    • Adjust the CAL knob until the meter needle points to the 'CAL' mark on the dial.
    • Without changing the CAL knob, switch the FUNCTION knob to SWR.
    • Read the SWR value directly from the SWR scale on the dial.
  6. PEP Measurement (for SSB):
    • Set the AVG/SSB switch to SSB.
    • Press the PEP button.
    • Transmit an SSB signal. The meter will display the Peak Envelope Power.

8. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the meter. Do not use abrasive cleaners or solvents.
  • Storage: Store the meter in a cool, dry place away from direct sunlight and extreme temperatures.
  • Connections: Periodically check all coaxial cable connections for tightness and corrosion.

9. Troubleshooting

  • No Power Indication: Ensure the 13.8V DC power supply is connected correctly and providing power. Check the power cable for damage.
  • Inaccurate Readings: Verify that the correct power range is selected. Ensure all coaxial connections are secure and that the antenna is properly tuned. Perform SWR calibration as described in the operating instructions.
  • High SWR Readings: A high SWR indicates a mismatch between your radio and antenna. Check your antenna system for faults, such as damaged cables, poor connections, or an improperly tuned antenna.

10. User Tips

  • For consistent SWR measurements, always calibrate the meter at the desired frequency and power level before taking a reading.
  • When measuring high power, start with the highest power range setting (200W) and decrease if necessary to avoid damaging the meter.

11. Warranty and Support

For warranty information or technical support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.