Jessinie FT4232-4TTL

Contents

FT4232-4TTL USB to 4 Way TTL Module

Model: FT4232-4TTL | Brand: Jessinie

1. Introduction

This manual provides detailed instructions for the proper use, installation, and maintenance of the Jessinie FT4232-4TTL USB to 4 Way TTL Module. This module, featuring the FT4232HL chip, is designed for high-demand industrial applications, enabling simultaneous communication with four independent UART serial ports via a single USB expansion. It offers flexible voltage selection (5V, 3.3V, 2.5V, 1.8V) and a maximum communication rate of 12Mbps.

Please read this manual thoroughly before operating the device to ensure safe and efficient use.

2. Safety & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

3. Product Overview

The FT4232-4TTL module is a versatile USB to 4-channel TTL serial port converter, ideal for various electronic projects and industrial applications. It features the high-performance FT4232HL chip, providing stable and reliable communication.

3.1 Key Features

  • Single USB expansion to 4 independent UART serial ports.
  • VCC, TX, RX can be switched to 5V, 3.3V, 2.5V, or 1.8V.
  • DC5.5-2.1 interface for providing high current to power external devices.
  • TX/RX indicators for each of the four UARTs to show communication status.
  • Four serial ports use XH2.54 interfaces for easy connection.
  • Maximum communication rate of 12Mbps.

3.2 Component Identification

Labeled diagram of FT4232-4TTL module components
Figure 1: Labeled components of the FT4232-4TTL Module. Key components include MicroUSB interface, Power Indicator, FT4232 chip, TTL power selection jumpers, Four-way TTL interfaces (J3), DC5V power supply input (J1), and TTL data sending/receiving indicators.
Top view of FT4232-4TTL module with dimensions
Figure 2: Top view of the FT4232-4TTL module showing its dimensions (76mm length x 30mm width).
Diagram showing VCC/TX/RX voltage selection and DC5.5-2.1 interface
Figure 3: Illustration of VCC, TX, RX voltage switchability (1.8V/2.5V/3.3V/5V) and the DC5.5-2.1 interface for external high-current power supply.
Diagram showing TX/RX indicators and XH2.54 serial interfaces
Figure 4: Illustration highlighting the TX/RX status indicators for each UART and the XH2.54 interface for the four serial ports.
Examples of applications for the FT4232-4TTL module
Figure 5: Various application examples for the FT4232-4TTL module, including keyboards, mice, mobile hard drives, USB drives, printers, and other USB-enabled devices.

Video 1: Product showcase of the FT4232-4TTL module, demonstrating its physical appearance and interfaces.

4. Specifications

FeatureDescription
Product NameFT4232-4TTL USB to 4 Way TTL Module
ModelFT4232-4TTL (FT4232HL chip)
TypeLogic ICs, Module
Supply VoltageDC 5V (via USB or external DC5.5-2.1 interface)
VCC TX RX Output VoltagesSelectable: 1.8V, 2.5V, 3.3V, 5V
Communication RateUSB high speed 480Mbps, UART up to 12Mbps
InterfacesMicroUSB, DC5.5-2.1 power input, 4-channel XH2.54 TTL serial ports
IndicatorsPower indicator, TX/RX indicators for each UART
ApplicationComputer, Switch and Sensor for Arduino STM
Dimensions (L x W x H)76mm x 30mm x 10mm (approx.)
Weight0.025 kg (approx.)
ConditionNew
CustomizationYes (is_customized)
High-concerned chemicalNone

5. Setup Instructions

5.1 Pre-Installation Considerations

Before integration, ensure that the operational environment aligns with specified technical parameters. It is recommended to verify compatibility with existing systems to facilitate seamless implementation.

5.2 Driver Installation

The FT4232HL chip requires specific drivers to function correctly with your computer. These drivers are typically available from the FTDI website or the manufacturer's support page. Install the appropriate drivers for your operating system before connecting the module.

5.3 Hardware Connection

  1. Connect to Computer: Use a USB cable to connect your computer to the MicroUSB interface (J2) on the module.
  2. Verify COM Ports: After the driver is installed, your computer should recognize the module and display 4 COM ports in your device manager.
  3. Select TTL Voltage: Use the short-circuit cap (jumper) to select the desired VCC/TX/RX voltage (1.8V, 2.5V, 3.3V, or 5V) on the TTL power selection interface (P1) to output the corresponding voltage to the connected devices. Refer to Figure 1 for the location of the TTL power selection.
  4. Connect TTL Devices: Connect your TTL devices to the four-way TTL interfaces (J3), ensuring correct pin alignment for VCC, RX, TX, and GND. The smallest value of the COM port typically corresponds to the first TTL interface, and the largest value corresponds to the fourth TTL interface (note that the COM port value assignment is not fixed and may vary).

Note on Power Supply:

  • When the module is powered by USB, the load must not exceed 500mA. Exceeding this limit may overload and damage the module or the computer's USB port.
  • If the module needs to carry a load of more than 500mA, it can be connected to a 5V high-current power supply at the DC5.5-2.1 interface (J1). Do not connect a power supply of other voltages to this interface.

6. Operating Instructions

6.1 General Guidance

This product is designed and manufactured in accordance with industry-standard specifications to ensure optimal performance and reliability. Users are expected to adhere to the following guidelines to maximize component functionality and service life.

6.2 Communication

Once connected and drivers are installed, you can use serial communication software on your computer to interact with devices connected to the TTL interfaces. The TX/RX indicator LEDs on the module will illuminate to show data transmission and reception status for each channel.

6.3 Simple Test

For a simple test of the module's functionality, you can short-circuit the TX and RX pins on one of the TTL interfaces. Then, use your host computer to send a message. If the setup is correct, you should receive an immediate data echo back to your computer.

6.4 Operational Notes

During use, maintain conditions within the prescribed ranges. Continuous monitoring of performance indicators is advised to sustain operational excellence.

7. Maintenance & Care

Implement routine maintenance protocols to uphold product standards. Periodic inspections are encouraged to ensure ongoing compliance with quality expectations. Store the module in a dry place and keep it away from children.

8. Troubleshooting

  • Module not recognized: Ensure drivers are correctly installed. Try a different USB port or cable.
  • No data transmission/reception: Check your wiring connections (VCC, RX, TX, GND) to the TTL device. Verify the selected voltage matches your device's requirements. Ensure the correct COM port is selected in your software.
  • Module overheating or computer USB port issues: Ensure the total current draw from the module (including connected devices) does not exceed 500mA when powered by USB. If higher current is needed, use an external 5V high-current power supply via the DC5.5-2.1 interface.
  • Incorrect voltage output: Double-check the position of the short-circuit cap on the TTL power selection interface (P1) to ensure it's set to the desired voltage.

9. User Tips

No specific user tips are available from provided reviews or Q&A content at this time. Always refer to the official documentation for best practices.

10. Compliance Information

10.1 CE Marking

The product conforms to the following EU Directives:

  • 2014/35/EU (Low Voltage Directive)
  • 2014/30/EU (Electromagnetic Compatibility Directive)

10.2 RoHS Declaration

This product is in compliance with Directive 2011/65/EU and its amendment (EU) 2015/863, concerning the restriction of hazardous substances (Pb, Cd, Hg, etc.) in electrical and electronic equipment.

11. Manufacturer & EU Representative Information

11.1 Manufacturer

Company Name: Shenzhen sijie electronics co., ltd

Full Address: CN-A, sixth floor, factory building no. 3, no. 41, baoan district 1, xin'an street, baoan district, shenzhen city, guangdong province, China, 518000

Phone: 86-17727547744

Email: jessinie2010@outlook.com

11.2 EU Authorized Representative

Company Name: eVatmaster Consulting GmbH

Full Address: Raiffeisen Street2 B11, 63110 Rodgau, Hessen, Germany

Email: contact@evatmaster.com

12. Support

For further details, consult the official documentation or contact our support team via the provided manufacturer's email address.

Disclaimer: The manufacturer assumes no liability for outcomes resulting from non-compliance with these instructions, improper use, or unauthorized modifications. Specifications are subject to change without prior notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.