ALLSOME BG-3306

Contents

ALLSOME BG-3306 Variable Speed Mini Benchtop Wood Lathe User Manual

Model: BG-3306

Introduction

This manual provides essential information for the safe and efficient operation of your ALLSOME BG-3306 Variable Speed Mini Benchtop Wood Lathe. Please read these instructions carefully before use and keep them for future reference. This machine is designed for multi-function use, serving as a wood lathe and, when equipped with a bench drill machine, a Buddha Beads machine.

Safety Instructions

WARNING: Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses; they are not safety glasses. Be certain the safety glasses you wear meet the appropriate standards.

General Safety Rules for Power Tools

  1. KEEP GUARDS IN PLACE and in working order.
  2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning on.
  3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
  4. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted.
  5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.
  6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
  7. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
  8. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed.
  9. DON'T OVERREACH. Keep proper footing and balance at all times.
  10. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.
  11. DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and the like.
  12. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.
  13. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories. The use of improper accessories may cause risk of injury.
  14. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
  15. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave tool until it comes to a complete stop.

Additional Safety Instructions For Lathes

  1. MAKE SURE ALL GUARDS are in place and that the Lathe sits on a flat, stable surface.
  2. ALWAYS WEAR EYE PROTECTION or a face shield when operating the Lathe. Use a respirator to avoid inhaling dust. All safety equipment should be ANSI approved.
  3. BEFORE STARTING THE MACHINE be certain the workpiece has been properly imbedded on the headstock and tailstock centers and that there is adequate clearance for the full rotation.
  4. ADJUST TOOL REST to provide proper support for the turning tool you will be using. Test tool rest clearance by rotating workpiece by hand before turning lathe on.
  5. SELECT THE TURNING SPEED which is appropriate for the type of work. Allow the lathe to gain its full speed before beginning turning.
  6. ALWAYS OBSERVE THE CONDITION of the materials you are turning. Pay particular attention to knots, splits and other potentially dangerous conditions.
  7. WHEN FACE PLATE TURNING, use lathe chisels on the downward spinning side of the workpiece only.
  8. NEVER OPERATE THE LATHE WITH DAMAGED OR WORN PARTS. Maintain your lathe in proper working condition. Perform routine inspections and maintenance promptly when called for. Put away adjustment tools after use.
  9. MAKE SURE YOUR WOOD LATHE IS TURNED OFF, disconnected from its power source and all moving parts have come to a complete stop before starting any inspection, adjustment, or maintenance procedure.
  10. DO NOT LEAVE LATHE RUNNING UNATTENDED for any reason.
  11. DO NOT STOP LATHE USING YOUR HAND against the workpiece.
  12. KEEP LOOSE CLOTHING ARTICLES such as sleeves, belts or jewelry items away from the lathe spindle.
  13. REMOVE THE TOOL REST when performing sanding or polishing operations on the rotating spindle.
  14. KEEP LATHE TOOLS PROPERLY SHARPENED and hold firmly in the proper position when turning.

Product Components and Controls

Diagram of ALLSOME BG-3306 Mini Benchtop Wood Lathe with labeled parts
Figure 1: Main parts of the ALLSOME BG-3306 Mini Benchtop Wood Lathe. Key components include the Headstock case, Speed controller, On/Off switch, Bed, Tool rest, Tailstock, Connector to drill machine, and Rubber feet. Specific controls labeled are Power switch, Speed switch, Plum top, Turning tool backing, Lock knob, and Advance and retreat knob.
Close-up of lathe headstock showing connections for accessories and replaceable drill chuck
Figure 2: Detail view showing the headstock's capability to connect to polishing discs, flexible shafts, etc., and the replaceable drill chuck on the tailstock.

Specifications

FeatureSpecification
Rated Input Power480W
No Load Speed0-5000 RPM (Variable Speed)
Output Shaft Thread SizeM14x1 (Note: Some descriptions mention M12x1, please verify on product nameplate)
Max. Wood Workpiece SizeLength 300mm x Diameter 40mm
Model NumberBG-3306
ConditionNew
OriginMainland China
CertificationNONE

Note: Specifications may be revised due to improvements. Always check the correct and real specifications on the nameplate of your machine.

Dimensions of the ALLSOME BG-3306 Mini Benchtop Wood Lathe
Figure 3: Overall dimensions of the lathe, showing length (660mm), height (160mm), and width (140mm), with a maximum workpiece length of 400mm and tailstock height of 90mm.

Assembly

This machine is designed for multi-functionality, serving as a wood lathe and a Buddha Beads machine when equipped with a bench drill machine.

Wood Lathe Configuration

  1. If using the machine solely as a wood lathe, remove the four rubber feet and the Connector plate designed for the drill machine.
  2. Secure the lathe to a bench using the two included screws. This will enhance stability during operation.

Buddha Beads Machine Configuration (with Bench Drill Machine)

  1. To configure as a Buddha Beads machine with a bench drill machine, slide the four included screws into both grooves of the Connector plate.
  2. Fix the lathe to the base of the bench drill machine.
  3. Tighten the nuts of the four screws securely.
ALLSOME BG-3306 Mini Benchtop Wood Lathe configured with a drill press for Buddha beads
Figure 4: The lathe assembled with a bench drill machine, demonstrating its use for creating Buddha beads.

Operation

To operate this, or any power tool, safely and efficiently, it is essential to become as familiar with its characteristics as possible. The time you invest before you begin to use this machine will be time well spent. DO NOT operate this machine until you are completely familiar with the contents of this manual. Make sure you read and understand all of the safety procedures. If you do not understand something, DO NOT operate the machine.

Operating Tips

  1. Make sure cutting tools are sharp and clean for best tool performance and safe operation.
  2. To avoid accidental starts, make sure the Speed Control knob is set at "0" before plugging in the electrical power cord.
  3. If any part of the Mini Wood Lathe becomes damaged during use, turn off the power immediately. Do not proceed with using the lathe until the problem area has been investigated and corrected.
  4. Never leave the working area until the lathe has been turned off and the spindle has come to a complete stop.
  5. Once a workpiece has been clamped onto the lathe, always rotate the workpiece by hand and check for proper tool rest clearance before turning on the electrical power.
  6. When turning a workpiece, always rough the wood to round form at a low speed to reduce the risk of workpiece kickback.
  7. Always position the Tool Rest above the centerline of the workpiece when shaping a piece of stock.
  8. Remove all loose knots in the stock before it is mounted on to the lathe.
  9. Always keep a firm hold on and maintain control of the cutting tool.
  10. If you are uncertain about the optimal speed, it is better to start with the slowest RPM and increase your speed as your comfort with the tool and the workpiece increases.
  11. Never force the tool or attachment to do the work of a larger industrial tool. It is designed to do the job better and more safely at the rate for which it was intended.

Turning Between Centers

  1. It is suggested that you start with a small workpiece for practicing wood lathe operation. Draw diagonal lines on each end to locate the center. Place the Center point or Cup center on the center point of one end of wood, and drive them using a wooden mallet. Then remove Spur center and cup center.
  2. Insert the Spur center into the headstock, and the Cup Center into the tailstock. Place the wood between the Spur Center and Cup Center, ensuring the diagonal point meets the center of them, and lock the Tailstock.
  3. Move the Cup Center into the workpiece by turning the Hand Wheel. Make sure that the Spur Center and the Cup Center are holding the workpiece in the end center points marked above.
  4. Adjust the Tool Rest so that the top of the Tool Rest is 2mm away from the corners of the workpiece and 2-5mm above the centerline of the workpiece. Rotate the workpiece by hand to make sure no portion of the workpiece touches the Tool Rest.
  5. Before turning on the Mini Wood Lathe, put the Speed Control Knob in position "0". Turn the Red button to start the lathe and slowly rotate the Speed Control Knob clockwise to increase the Spindle speed. If you are uncertain about the optimal spindle speed, it is better to start with the slowest RPM and increase the speed as your comfort with the tool and the workpiece increases.
  6. Positioning the Tool Rest for cutting: When cutting, the object is to pierce the outer skin of the workpiece to a certain designed depth, then hold the cutting tool steady with the beveled edge parallel to the work circumference. In this manner, the cutting tool will shove the workpiece at the desired depth. The best way to hold the cutting tool steady is to rest it on the Tool Rest. The Tool Rest will act as a fulcrum point to support the cutting tool against the downward force of the revolving workpiece.

A Tool Rest which is placed too low will result in the cutting edge continuing to dig deeper into the workpiece, resulting in a "bite" so deep that the cutting tool will begin to bounce and chatter and become very difficult to hold safely. If the Tool Rest is placed too high and the cutting tool hits the workpiece near to top (where the direction of force exerted by the workpiece is nearly horizontal), a strong and dangerous kickback will occur. If the Tool Rest is placed too far away from the workpiece, the cutting tool will again hit too high on the workpiece. Leverage will be reduced and it will be very difficult to safely hold the cutting tool. As a general rule, with small diameter workpiece the Tool Rest should be positioned very close to the workpiece 2mm.

Mini wood lathe in operation, turning a wooden workpiece
Figure 5: The lathe in operation, demonstrating turning a workpiece between centers.

Making Buddha Beads

  1. Adjust the position of the Lathe or the Head of the drill machine to ensure the diagonal line between the Spur Center and Cup Center of the Wood lathe is aligned with the center point of the drill bits. Otherwise, the Buddha beads will not be round.
  2. The speed of the Lathe and Drill machine affects the finish of the workpiece surface. Faster speeds generally result in a better finish. The highest speed is recommended for both Lathe and Drill machine operations.
  3. Feed the cutting tool very slowly when close to the Buddha beads center (2mm), and stop cutting when 1.5mm.
  4. After stopping the Lathe, remove the Buddha beads and cut them by hand knife. If the Buddha beads are slightly larger than desired, sanding and polishing can achieve the desired size.
Close-up of wood turning and drilling operations on the mini lathe
Figure 6: Demonstrating both wood turning (top) and drilling (bottom) operations, relevant for making Buddha beads.

Maintenance

  • After each use, the Mini Wood Lathe should be thoroughly cleaned.
  • Keep the lathe dry at all times.
  • Occasionally, moving parts should be lubricated with a good quality machine oil.

Troubleshooting

This section addresses common issues you might encounter with your ALLSOME BG-3306 Mini Benchtop Wood Lathe.

  • Tool not starting: Ensure the Speed Control knob is set to "0" before plugging in. Check the power connection and the On/Off switch.
  • Workpiece vibration/chatter: Verify that the workpiece is securely clamped between centers. Adjust the Tool Rest position (2mm from workpiece, 2-5mm above centerline) and ensure it's firmly locked. Reduce turning speed if necessary.
  • Inconsistent turning results: Ensure your cutting tools are sharp. Check for loose knots or splits in the wood. Maintain a firm grip on the cutting tool and apply steady pressure.
  • Overheating: Avoid forcing the tool. Ensure proper ventilation around the motor. If the tool feels excessively hot, turn it off and allow it to cool before resuming operation.
  • Damaged parts: If any part is damaged, discontinue use immediately. Inspect the tool thoroughly and replace or repair damaged components before further operation.

User Tips

  • Spindle Thread Size: While specifications might vary, some users have noted the spindle thread is M14x1. If you plan to use a lathe chuck, K01-50 and K02-50 models are often compatible, but verify the thread size on your specific unit.
  • Chuck Compatibility: The machine typically comes with centers, not a lathe chuck. If you need a 4-jaw chuck or mandrel for specific projects like pen turning, these usually need to be purchased separately.
  • Power Supply: The machine operates on 220V. Ensure your power supply matches this requirement.
  • RPM Stability: The variable speed control allows adjustment from 0-5000 RPM. While it maintains speed well, heavy loads might cause slight drops. Start with lower RPMs and gradually increase as you gain comfort and the workpiece allows.

Spare Parts List

Refer to the table below for a list of common spare parts. For detailed diagrams, please consult the official user manual PDF.

No.Part NameNo.Part NameNo.Part Name
1Screw ST4X1821Screw M4x1041Screw M5x22
2Headstock cover22Plastic screw M4x1642Spur center
3Upper Headstock23Copper adjust plate43Chuck nut
4Motor assy.24Connector plate44Chuck
5Speed controller25Nut M545Output shaft
6Thin nut M826Screw M5x2546Bearing 6002
7Speed knob27Right cover47Driven pulley
8Cord sleeve28Screw ST4x1648Lock screw M5x5
9Cord29Tailstock fix nut49Circlip for shaft 15
10Down headstock30Tailstock fix screw50Cord anchor
11Screw M5x1231Tailstock51Belt
12Flat washer 532Handwheel52Bearing cover
13Spring washer 533Threaded rod M4x853Drive pulley
14Lathe bed34Cup center54Lock screw M4x6
15Rubber feet35Tool rest fix nut55On/Off switch
16Screw ST5X2036Tool rest base56Guard stand
17Screw M8x2537Tool rest stand57Guard
18Flat washer 838Adjust screw58Spring
19Nut M839Tool rest59Screw M5x50
20Nut M440Nut M5
Included accessories and parts for the mini wood lathe
Figure 7: Various accessories and spare parts included with the lathe, such as chuck, belt, wrenches, and screws.

Warranty and Support

For detailed warranty information, technical support, or to access the full user manual, please refer to the official documentation provided by ALLSOME. A PDF version of the user manual is available for download: User Manual (PDF).

For further assistance, please contact ALLSOME customer service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.