Heltecbms HT-616L Series BMS BOARD

Contents

Heltec HT-616L Series Battery Management System User Manual

Model: HT-616L Series BMS BOARD | Brand: Heltecbms

1. Product Introduction

This device is an intelligent balancing protection board designed specifically for 6S-16S series lithium batteries, supporting ternary lithium/lithium iron phosphate batteries. Its main advantages include protecting the battery from overcharging, over-discharging, over-current, over-temperature, and short circuit. It provides balanced charging to achieve long-term maintenance of the battery through voltage balancing, thereby extending the service life of the battery pack. It is suitable for series-connected lithium battery packs. Once the individual cell voltage reaches the equilibrium turn-on voltage, the high voltage battery will be balanced until the equilibrium release voltage is reached.

2. Product Model Selection

ParameterValue
Number of strings6S-16S
Current30A/50A/80A
Applicable batteryNCM/LFP

Note: The currently available models are listed in the table above. For other requirements, customization of 6-16S series is supported.

3. Product Model Description

To understand the model naming convention, consider a 50A protective board with 12 strings as an example:

  • HT-616 LOS 12S 50A or HT-616 LPS 12S 50A
    • 616: Indicates this series can support 6 to 16 strings.
    • LOS: Denotes suitability for NCM (Nickel Cobalt Manganese) batteries.
    • LPS: Denotes suitability for LFP (Lithium Iron Phosphate) batteries.
    • 12S: Represents the number of strings for this BMS board.
    • 50A: Specifies the discharge current of this BMS board.

4. Specifications

4.1. Lithium Iron Phosphate (LFP) Parameters

Test conditions: room temperature 25 °C. The over-current value and internal resistance of the protection board are dynamic parameters. The voltage of each battery cell needs to be ≥ 3.25 V during testing.

ProjectSymbolDetailed ContentStandard
Serial numberSNumber of battery strings6-16S
CurrentACurrent that the shield can withstand30/50/80A
Battery typeLithium iron phosphateLithium iron phosphate
Overcharge detection voltageVDET1Overcharge detection voltage3.65V±0.035V
Overcharge detection delay timetVDET1Overcharge detection delay time1.3s (MAX)
Overcharge relieve voltageVREL1Overcharge relieve voltage3.55V±0.025V
Over discharge test voltageVDET2Over discharge test voltage2.350V±0.025V
Delay time for over discharge detectiontVDET2Delay time for over discharge detection1.5s (MAX)
Over discharge relieve voltageVREL2Over discharge relieve voltage2.55V±0.025V relieve
Discharge over-current detection voltageVDET3Discharge over-current detection voltage100mV±25mV
Theoretical instantaneous single pulse currentIDP@3.6V, 20-45°C MOSFET temp120A/200A/320A
Actual instantaneous multi-pulse currentIDP90A/150A/240A
Duration1s
Protection release conditionBreak short circuit
Short-circuit protection conditionsExternal load circuit short circuit
Short-circuit detection delay timeTSHORT300uS (MAX)
Short-circuit protection release conditionsBreak short circuit
Main circuit on state resistanceRDS@3.4V battery voltageB- to P-RDS≤0.3mΩ
Internal consumptionIDDDuring operationMIN: 0.3μΑ MAX: 100μΑ
Electricity balance detection voltageVBU3.405V±0.035V
Balance startup delay timetVBU1.6S (MAX)
Balance release voltageVBL3.4V±0.035V
4.2V battery balance currentIB100mA±5mA
Low temperature charging protection-0 °C± 5 °CNo
High temperature charging protection75 °C± 5 °CYes
MAX continuous working current (Charge)Rated current of charger30A/50A/80A (Equivalent to A of the protective board)
MAX continuous working current (Discharge)Rated current of battery pack30A/50A/80A (Equivalent to A of the protective board)
Charger selection voltageNumber of strings × 3.65V ± 0.05V30A/50A/80A (Equivalent to A of the protective board)
Charging MOS MAX withstand voltageVDSDC 85V

4.2. Ternary Lithium (NCM) Parameters

Test conditions: room temperature 25°C. The over-current value and internal resistance of the protection board are dynamic parameters. The voltage of each battery cell needs to be ≥ 3.7 V during testing.

ProjectSymbolDetailed ContentStandard
Serial numberSNumber of battery strings6S-16S
CurrentAMax continuous current30/50/80A
Battery typeTernary lithiumTernary lithium
Overcharge detection voltageVDET1Overcharge detection voltage4.25V±0.035V
Overcharge detection delay timetVDET1Overcharge detection delay time1.3s (MAX)
Overcharge relieve voltageVREL1Overcharge relieve voltage4.2V±0.025V
Over discharge test voltageVDET2Over discharge test voltage2.8V±0.025V
Delay time for over discharge detectiontVDET2Delay time for over discharge detection1.5s (MAX)
Over discharge relieve voltageVREL2Over discharge relieve voltage3.0V±0.025V relieve
Discharge over-current detection voltageVDET3Discharge over-current detection voltage100mV±5mV
Theoretical instantaneous single pulse currentIDP@3.6V, 20-45°C MOSFET temp120A/200A/320A
Actual instantaneous multi-pulse currentIDP90A/150A/240A
Duration1s
Protection release conditionBreak short circuit
Short-circuit protection conditionsExternal load circuit short circuit
Short-circuit detection delay timeTSHORT300uS (MAX)
Short-circuit protection release conditionsBreak short circuit
Main circuit on state resistanceRDS@3.4V battery voltageB- to P-RDS≤0.3mΩ
Internal consumptionIDDDuring operationMIN: 0.3μΑ MAX: 100μΑ
Electricity balance detection voltageVBU4.22V±0.035V
Balance startup delay timetVBU1.6S (MAX)
Balance release voltageVBL4.21V±0.035V
3.59V battery balance currentIB100mA±5mA
Low temperature charging protection-0 °C± 5 °CNo
High temperature charging protection75 °C± 5 °CYes
MAX continuous working current (Charge)Rated current of charger30A/50A/80A (Equivalent to A of the protective board)
MAX continuous working current (Discharge)Rated current of battery pack30A/50A/80A (Equivalent to A of the protective board)
Charger selection voltageNumber of strings × 3.65V ± 0.05V30A/50A/80A (Equivalent to A of the protective board)
Charging MOS MAX withstand voltageVDSDC 100V

4.3. Specific Configuration Parameters

The following parameters apply to specific configurations of the HT-616L Series BMS:

11S, 12S, 13S, 14S (30A, 3.7V, Same Port)

  • Size: 72*55*8mm
  • Overcharge protection: 4.25V ± 0.25V
  • Charging recovery: 4.2V
  • Over-discharge protection: 2.8V ± 0.25V
  • Discharge recovery: 3.0V
  • Maximum continuous current: 30A
  • Peak Current: 66A
  • Balance current: 80 mA
  • Balanced starting voltage: 4.15V ± 0.25V
  • Self-consumption: ≤35uA
  • Application: Applicable to 48V Electric bicycle and electric tools within 550W

6S, 7S (20A, 3.7V, Same Port)

  • Size: 72*55*8mm
  • Overcharge protection: 4.25V ± 0.25V
  • Charging recovery: 4.2V
  • Over-discharge protection: 2.8V ± 0.25V
  • Discharge recovery: 3.0V
  • Maximum continuous current: 30A
  • Peak Current: 100A
  • Balance current: 80 mA
  • Balanced starting voltage: 4.15V ± 0.25V
  • Self-consumption: ≤35uA
  • Application: Applicable to 48V Electric bicycle and electric tools within 550W

8S (30A, 3.2V, Same Port)

  • Size: 72*55*8mm
  • Overcharge protection: 3.75V ± 0.25V
  • Charging recovery: 3.55V
  • Over-discharge protection: 2.2V ± 0.25V
  • Discharge recovery: 2.7V
  • Maximum continuous current: 30A
  • Peak Current: 100A
  • Balance current: 80 mA
  • Balanced starting voltage: 3.515V ± 0.25V
  • Self-consumption: ≤35uA
  • Application: Applicable to 48V Electric bicycle and electric tools within 550W

5. Size and Dimensions

The length and width of the 6-16S series protection board are consistent, with thickness varying based on the current rating.

Heltec BMS board with dimensions 55mm width and 70mm height

Figure: Heltec BMS board showing approximate dimensions (55mm width, 70mm height).

Current30A50/80A
Thickness (MM)812

6. Setup: Wiring Diagram

Correct wiring is crucial for the safe and proper operation of the Battery Management System. Please follow the diagrams carefully for your specific battery configuration. Ensure all connections are secure before operation.

Wiring diagram for 6S Battery Management System

Figure: Wiring Diagram for 6S Battery Management System. This diagram illustrates the connections for a 6-cell series battery pack to the BMS, including battery positive (Pack+), battery negative (Pack-), charge negative (Charge-), and the balance leads (B- to B6).

Wiring diagram for 7S Battery Management System

Figure: Wiring Diagram for 7S Battery Management System. This diagram shows the connections for a 7-cell series battery pack to the BMS, including battery positive (Pack+), battery negative (Pack-), charge negative (Charge-), and the balance leads (B- to B7).

Wiring diagram for 8S Battery Management System

Figure: Wiring Diagram for 8S Battery Management System. This diagram details the connections for an 8-cell series battery pack to the BMS, including battery positive (Pack+), battery negative (Pack-), charge negative (Charge-), and the balance leads (B- to B8).

Wiring diagram for 10S Battery Management System

Figure: Wiring Diagram for 10S Battery Management System. This diagram illustrates the connections for a 10-cell series battery pack to the BMS, including battery positive (Pack+), battery negative (Pack-), charge negative (Charge-), and the balance leads (B- to B10).

For 12S, 13S, 14S, and 16S configurations, the wiring principle is similar to the diagrams provided above. Connect the balance leads from B- (negative terminal of the first cell) up to the positive terminal of the last cell (B12, B13, B14, or B16 respectively). Ensure the main battery positive (Pack+) and negative (Pack-) terminals are connected, along with the charge negative (Charge-) and controller connections as indicated in the general wiring diagrams.

General connection diagram for BMS

Figure: General connection diagram for the BMS, showing the main power connections and balance leads.

Detailed general connection diagram for BMS

Figure: Detailed general connection diagram for the BMS, providing a clearer view of the wiring points.

7. Product Accessories

The Heltec HT-616L Series BMS typically includes the following accessories:

  • BMS Board: The main Battery Management System unit.
  • Collection Line (Balance Leads): Two sets of balance wires (e.g., for 6S/7S/8S/10S configurations, one set of wires is provided). These wires are used to connect to each individual cell in the battery pack for voltage monitoring and balancing.
Heltec BMS board with included balance wires

Figure: Heltec BMS board with its accompanying balance wires.

8. Operating Principles

The Heltec HT-616L Series BMS is designed to manage and protect lithium battery packs, ensuring their longevity and safe operation. Its core functions include:

  • Overcharge Protection: Prevents individual battery cells from being charged beyond their safe voltage limit, which can lead to damage or thermal runaway.
  • Over-discharge Protection: Stops discharging when cells reach their minimum safe voltage, preventing irreversible damage and capacity loss.
  • Over-current Protection: Limits the current drawn from the battery to prevent damage to the cells and the BMS itself.
  • Short Circuit Protection: Immediately cuts off power in the event of a short circuit to prevent severe damage and fire hazards.
  • Over-temperature Protection: Monitors the battery temperature and takes action (e.g., reducing current or shutting down) if it exceeds safe operating limits.
  • Balanced Charging: Actively balances the voltage of individual cells within the pack during charging. When a cell reaches the equilibrium turn-on voltage, the BMS will balance it until the equilibrium release voltage is reached, ensuring all cells are charged uniformly.

9. Maintenance

To ensure the optimal performance and longevity of your Heltec HT-616L Series BMS and battery pack, consider the following maintenance guidelines:

  • Regular Inspection: Periodically check all wiring connections for looseness or damage. Ensure the BMS board is securely mounted and free from physical stress.
  • Environmental Conditions: Operate the BMS within its specified temperature range. Avoid exposure to extreme heat, cold, moisture, or corrosive environments.
  • Battery Health: Monitor the overall health of your battery pack. While the BMS provides protection, severely degraded cells can still impact performance.
  • Software Updates: If applicable, check the manufacturer's website for any firmware or software updates for your BMS model.
  • Cleaning: Keep the BMS board clean and free of dust and debris. Use a soft, dry brush or compressed air for cleaning.

10. Troubleshooting and Fault Handling

This section outlines common fault phenomena, their potential causes, and recommended processing methods.

Fault PhenomenonFault Inspection and CauseProcessing Method
Can't dischargeFirst, connect the circuit to activate the protection board for charging, and then measure the voltage of each battery separately. If the voltage of any battery is lower than 3.0V±0.025V (NCM) / 2.35V±0.025V (LFP), the protection board will start over-discharge protection.If the battery is lower than 3.0V, please charge the battery to 3.7V (NCM) / 3.25V (LFP) and balance it before combining. Do not mix good batteries with poor batteries. If you cannot solve this problem, please contact after-sales service.
Can't chargeMeasure the voltage of each battery section. If any battery voltage is higher than 4.215V (NCM) / 3.615V (LFP), the protection board will start overcharge protection.If the battery is higher than 4.215V (NCM) / 3.615V (LFP), please discharge the battery to about 3.7V until it is balanced before combining. Do not mix good batteries with poor batteries (if you cannot solve this problem, please contact after-sales).
Charging/discharge failureB-, B1, B2, B3, ......B+ Wrong wiringRedraw the wiring or operate under the guidance of customer service.
Overcharge/discharge protection is invalidB-, B1, B2, B3, ......B+ Wrong wiringRedraw the wiring or operate under the guidance of customer service.
Discharge protectionCheck whether the current value of the load starting power supply exceeds the over-current protection current of the protection board.Replace the protection board with a larger current (if not solved, please contact after-sales).
Component is welded looselyOne of the components has a pin that is not connected to the PCB pad.You can repair the welding by yourself (if it still cannot be solved, please contact after-sales).
Component weldingThere is a short circuit between two or more pins of the element.Remove the component and re-weld (if not, please contact after-sales).
Electrostatic breakdownWhen the MOS tube is not powered, the forward and reverse resistance of any two pins of the G, D and S terminals are 0.You can remove and replace the MOS tube by yourself (if it still cannot be solved, please contact after-sales).

11. User Tips

No specific user tips were available from provided reviews or Q&A content.

12. Quality Assurance and Manufacturing

Heltec is committed to producing stable Battery Management System products. The manufacturing process involves automated assembly and rigorous testing to ensure product quality.

Video: Overview of the Heltec BMS manufacturing process, showcasing automated assembly lines and manual quality checks.

Detailed view of BMS components

Figure: Close-up view of BMS components, highlighting the quality of assembly.

Detailed view of BMS components

Figure: Another detailed view of BMS components, emphasizing precision manufacturing.

Detailed view of BMS components

Figure: A further detailed view of BMS components, showcasing the robust design.

13. Warranty and Support

Warranty Regulations

The warranty service period for this product is 1 year. The warranty service is limited to normal use and does not cover man-made damage, self-disassembly, modification and repair, use not in accordance with the instructions, or damage caused by external force majeure factors. Accessories such as test fixtures are considered consumables and are not covered by warranty.

For warranty service, please contact your dealer for processing. If you cannot contact the dealer, you can contact our company by email or phone. Please note that there are no after-sales service stations in other countries except China. If you require warranty service and are outside China, you will need to send the product to us for free repair, but you will be responsible for the freight for the round trip.

Our company guarantees that each product is shipped after being tested by professional protection board testing instruments. Due to the nature of electronic components, the combination battery of the protection board may be damaged by static electricity and current, and it is normal to have defective products in use.

For a comprehensive guide and additional documentation, please refer to the official user manual PDF: Heltec HT-616L Series User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.