EFT Spreader V2.0

Contents

EFT Spreader V2.0 Instruction Manual

Model: Spreader V2.0 | Brand: EFT

1. Introduction

The EFT Spreader V2.0 is an advanced and versatile spreading system designed for integration with plant protection drones. This system is engineered for precise and efficient distribution of various solid particles, including seeds, fertilizers, and baits. Available in 10L and 22L capacities, it offers robust performance and multi-platform compatibility for agricultural and other specialized drone applications.

This manual provides essential information for the safe and effective setup, operation, and maintenance of your EFT Spreader V2.0.

2. Key Features

  • Versatile Particle Spreading: Supports a wide range of solid particles such as grass seeds, sowing seeds, feeding pellets, fertilizers, and deicing agents.
  • Capacity Options: Available in 10L and 22L tank capacities to suit different operational needs.
  • Precise Control: Features an adjustable discharge valve and rotary table speed for accurate control over discharge quantity and speed.
  • Advanced Control Module: Equipped with an integrated independent control module, featuring a board-level potting process and an integrated heat sink for enhanced stability and reliability.
  • Dual Control Modes: Supports both conventional PWM control mode and CAN bus control mode, allowing deep adaptation to various flight control systems.
  • Robust Waterproof Design: Adopts multiple waterproof processes, achieving an IP67 waterproof level, allowing direct washing with water for easy cleaning.
  • Tool-Free Quick Release: Designed for quick assembly and disassembly with three hand-tight screws, simplifying maintenance and interchangeability.
  • 360° Large Flow Spreading: Features a 360° spreading mechanism with a maximum discharge opening area of 43 cm², significantly improving spreading efficiency.
  • Multi-Platform Compatibility: As an independent subsystem, it is compatible with various flying platforms, including EFT G series and EP series plant protection drones (e.g., E410P, E416P, E610P, E616P).

3. Setup and Installation

The EFT Spreader V2.0 is designed for straightforward installation on compatible plant protection drones. Follow these general steps for setup:

  1. Unpacking: Carefully unpack all components of the spreader system. Verify that all parts are present according to the packing list.
  2. Mounting the Spreader Unit:

    Attach the main spreader unit (motor and fan assembly) to the designated mounting points on your drone's frame. Ensure it is securely fastened. The system is designed to be mounted to the drone's "Upper Shell" or chassis.

    EFT Spreader V2.0 side view showing motor and wiring

    Image: Side view of the EFT Spreader V2.0, illustrating the motor and wiring connections.

  3. Attaching the Tank:

    Position the 10L or 22L tank onto the spreader unit. The system features a tool-free quick release design, utilizing three hand-tight screws for secure attachment. Ensure the tank is properly aligned and locked into place.

    EFT Spreader V2.0 tank with mounting plate

    Image: The EFT Spreader V2.0 tank with its integrated mounting plate, ready for attachment.

    Diagram showing tool-free quick release design with three hand-tight screws

    Image: Diagram illustrating the tool-free quick release design, highlighting the three hand-tight screws for easy assembly and disassembly.

  4. Electrical Connections:

    Connect the spreader's power and control wiring to your drone's flight controller or power distribution board. The spreader uses an independent control module. Refer to your drone's manual for specific wiring diagrams and power requirements. Ensure all connections are secure and properly insulated.

    Diagram showing 4 independent control module and multi-type particle spreading

    Image: Diagram detailing the 4 independent control module and its integration, alongside examples of multi-type particle spreading.

  5. System Integration:

    Configure your drone's flight control system to recognize and operate the spreader. The system supports both PWM and CAN control modes. Select the appropriate mode and calibrate as necessary according to your flight controller's instructions.

    Diagram showing multi-platform compatibility and two control modes (PWM and CAN)

    Image: Diagram illustrating multi-platform compatibility with G series and EP series drones, and the two available control modes: PWM and CAN.

4. Operating Instructions

Once installed and configured, the EFT Spreader V2.0 offers precise control over material distribution.

  1. Filling the Tank:

    Open the tank cap and carefully fill the tank with the desired solid particles (seeds, fertilizer, bait, etc.). Ensure the material is dry and free of large clumps that could obstruct the discharge mechanism. Do not overfill the tank beyond its rated capacity (10L or 22L).

    EFT Spreader V2.0 top view showing motor, wiring, and cap

    Image: Top view of the EFT Spreader V2.0, showing the tank cap for filling.

  2. Adjusting Discharge Quantity:

    The discharge valve can be adjusted to control the flow rate of the material. Perform ground tests to determine the optimal valve setting for your specific material and desired spreading density.

  3. Adjusting Spreading Speed:

    The speed of the rotary table is adjustable, influencing the spread width and uniformity. Experiment with different speeds to achieve the desired coverage pattern.

    Close-up of the spreader's motor and fan mechanism

    Image: Close-up of the spreader's motor and fan mechanism, responsible for particle distribution.

  4. Initiating Spreading:

    Once the drone is airborne and positioned correctly, activate the spreading function via your drone's remote controller. Monitor the spreading operation and adjust settings as needed.

  5. Ending Spreading:

    Deactivate the spreading function before landing or when the task is complete. Ensure the discharge valve is closed to prevent accidental spills.

5. Maintenance and Care

Regular maintenance ensures the longevity and optimal performance of your EFT Spreader V2.0.

  • Cleaning:

    Due to its IP67 waterproof rating, the entire system can be washed directly with water. After each use, especially when spreading corrosive materials like certain fertilizers, thoroughly clean the tank and spreading mechanism to prevent residue buildup and corrosion. Ensure all components are dry before storage.

  • Disassembly for Cleaning:

    Utilize the tool-free quick release design to easily detach the tank and access the spreading mechanism for thorough cleaning. This allows for removal of any lodged particles or debris.

  • Inspection:

    Periodically inspect all moving parts, electrical connections, and the tank for any signs of wear, damage, or loose fasteners. Replace any worn or damaged components immediately.

  • Storage:

    Store the spreader in a clean, dry environment away from direct sunlight and extreme temperatures when not in use.

6. Troubleshooting

This section addresses common issues you might encounter with your EFT Spreader V2.0.

ProblemPossible CauseSolution
Spreader not activating
  • Loose electrical connection
  • Incorrect flight controller configuration
  • Power supply issue from drone
  • Check all wiring connections for security.
  • Verify PWM/CAN settings in your drone's flight controller.
  • Ensure the drone's power system is supplying adequate power.
Uneven spreading or no material discharge
  • Discharge valve closed or obstructed
  • Material clumping or foreign objects in tank
  • Rotary table not spinning
  • Check and adjust the discharge valve.
  • Empty the tank, inspect for obstructions, and ensure material is free-flowing.
  • Check motor connections and ensure it's receiving power.
Spreader motor making unusual noise
  • Debris caught in the mechanism
  • Motor damage
  • Disassemble using quick-release and inspect for debris; clean thoroughly.
  • If noise persists after cleaning, contact support.

7. Specifications

AttributeDetail
Model NumberEFT Spreader V2.0
Capacities Available10L, 22L
Dimensions (Approx.)800 x 800 x 500 mm
MaterialCarbon Fiber (frame/mount), Durable Plastic (tank)
Waterproof RatingIP67
Control ModesPWM, CAN Bus
Discharge Opening AreaMax 43 cm²
CompatibilityEFT G series, EP series plant protection drones (e.g., E410P, E416P, E610P, E616P)
Power SourcePowered by drone (No internal battery)
Recommended Age14+ years

8. User Tips

No specific user tips were available from reviews or Q&A for this product. However, general best practices for drone spreading systems include:

  • Always perform a pre-flight check of the spreader, ensuring it's securely mounted and connections are tight.
  • Test the spreading pattern and flow rate with inert material before applying valuable or sensitive substances.
  • Keep the spreading material dry and free of debris to prevent clogging.
  • Regularly clean the spreader, especially after using corrosive chemicals, to extend its lifespan.

9. Warranty and Support

For warranty information, technical support, or service inquiries regarding your EFT Spreader V2.0, please contact the seller or manufacturer directly. Keep your purchase receipt and product model details handy when contacting support.

Seller: June Airplane RC Store

Seller Contact: Refer to your purchase platform for direct messaging or contact options.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.