SUNBUCK 336BU

Contents

SUNBUCK 2000W Bluetooth Stereo Amplifier User Manual

Model: 336BU

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your SUNBUCK 2000W Bluetooth Stereo Amplifier. Designed for home cinema and karaoke applications, this amplifier offers versatile connectivity and powerful audio output. Please read this manual thoroughly before using the product to ensure proper and safe operation.

2. Features

  • Suitable for small party and home audio setups.
  • Dual signal inputs: DVD and AUX.
  • LINE output for connecting to active subwoofers or other external audio equipment.
  • Center surround output with 2 channels (center one, surround two).
  • Includes a remote control for convenient operation.
  • Integrated Bluetooth 5.0 for wireless audio streaming.
  • Built-in FM radio tuner.
  • 5-band EQ mixer for precise audio customization.
  • Reverberation, fine tuning, and balance controls.
  • SD and USB interfaces for media playback.
  • Four microphone inputs with reverb and delay adjustment for karaoke.

3. Specifications

ParameterValue
Model336BU
Dimensions (L x W x H)290 × 95 × 240 mm (11.4 x 3.7 x 9.4 in)
Rated VoltageAC 110V/220V 50/60Hz, DC12V
Rated Power1200W
Peak Power2000W
Rated Frequency20Hz - 20KHz
Signal to Noise Ratio90dB
Standard Impedance4 to 16 ohm
Channel Type2.0 channel (AV power amplifier)
Total Harmonic Distortion≤ 0.5%
Signal Input Sensitivity200mv (± 30mv)
Microphone Input Sensitivity9 mv (± 2mv)
Recording Level Output1V
Auxiliary Level Output1V
Supported MediaUSB Disk/Max 64GB SD Card (Not included)
ColorBlack

Note: Actual maximum power output is approximately 80-90W.

4. Package Contents

Please check the package for the following items:

  • 1 x SUNBUCK Audio Power Amplifier
  • 1 x Remote Control
  • 1 x User Manual

Note: USB Disk and SD Card (up to 64GB) are not included and must be purchased separately.

5. Safety Information

  • Ensure the amplifier is placed on a stable, flat surface with adequate ventilation.
  • Do not expose the unit to rain, moisture, or extreme temperatures.
  • Before connecting or disconnecting any cables, ensure the amplifier is turned off and unplugged from the power source.
  • Use only the specified power voltage (AC 110V/220V or DC12V) to avoid damage.
  • Do not open the amplifier casing; there are no user-serviceable parts inside. Refer all servicing to qualified personnel.
  • Keep out of reach of children.

6. Setup and Connections

Before powering on, ensure all connections are secure.

6.1 Front Panel Overview

Front panel of the SUNBUCK amplifier with labels for MIC inputs, volume, EQ, USB/SD, and LED display.
Figure 6.1: Front Panel Controls and Inputs

The front panel features controls for microphone input (MIC1-MIC4), individual mic adjustments, Treble, Mid, Bass, Echo, and Balance. The main Volume knob controls overall output. The USB/SD/MMC/FM/BT Player section includes an LED display, USB port, and SD card slot.

6.2 Rear Panel Connections

Rear panel of the SUNBUCK amplifier with labels for Audio Input, Audio Output, Speaker System, Antenna, AC power, and DC 12V input.
Figure 6.2: Rear Panel Connections
  • Antenna: Connect the FM antenna for radio reception.
  • AC 110V/220V Input: Connect the amplifier to a suitable AC power outlet using the provided power cord.
  • DC 12V Input: For alternative power supply, connect a DC 12V source.
  • Audio Input (LINE IN): Connect external audio sources (e.g., DVD player, CD player) using RCA cables. The amplifier supports both DVD and AUX signal inputs.
  • Audio Output (LINE OUT): Connect to an active subwoofer or other audio equipment.
  • Speaker System (Left/Right Channels): Connect your passive speakers to these terminals. Ensure correct polarity (+ to + and - to -) for optimal sound. The amplifier supports speakers with an impedance of 4 to 16 ohms.
Diagram showing how to connect various types of speakers to the amplifier's speaker system terminals.
Figure 6.3: Speaker Connection Diagram

6.3 Microphone Inputs

Close-up of the four microphone input jacks on the front panel.
Figure 6.4: Four Microphone Inputs

The amplifier provides four microphone inputs (MIC1-MIC4) on the front panel, each with independent volume and effect adjustments for karaoke or public address use.

7. Operating Instructions

7.1 Power On/Off

Press the 'POWER' switch on the front panel to turn the amplifier on or off.

7.2 Input Selection

Use the 'INPUT' button or the remote control to cycle through available audio sources: DVD, AUX, USB, SD, FM, and Bluetooth.

7.3 Volume and Tone Control

  • VOLUME: Adjust the master volume using the large knob on the front panel or the remote control.
  • TREBLE, MID, BASS: Use these knobs to adjust the high, mid, and low frequencies of the audio output.
  • BALANCE: Adjust the left/right channel balance.

7.4 USB/SD Card Playback

Close-up of the USB and SD card input slots on the front panel.
Figure 7.1: USB/SD Card Inputs

Insert a USB disk or SD card (up to 64GB, not included) into the respective slot on the front panel. The amplifier will automatically switch to USB/SD mode and begin playback. Use the controls in the USB/SD/MMC/FM/BT Player section or the remote to navigate tracks and control playback.

7.5 AUX Input

Close-up of the AUX input jack on the front panel.
Figure 7.2: AUX Input

Connect an audio device (e.g., smartphone, MP3 player) to the AUX input jack on the front panel using a 3.5mm audio cable. Select 'AUX' as the input source.

7.6 Bluetooth Connectivity

Image showing the amplifier with a Bluetooth symbol and a smartphone, indicating Bluetooth connectivity.
Figure 7.3: Bluetooth 5.0 Connectivity

Select 'BT' (Bluetooth) as the input source. The amplifier will enter pairing mode. On your mobile device, search for available Bluetooth devices and select 'SUNBUCK' (or similar name) to connect. Once paired, you can stream audio wirelessly.

7.7 FM Radio

Select 'FM' as the input source. Use the tuning controls on the front panel or remote to scan for and select radio stations.

7.8 Microphone and Karaoke Functions

  • Connect microphones to the MIC1-MIC4 inputs.
  • Adjust individual microphone volumes using the dedicated knobs.
  • Use the 'ECHO' knob to add reverberation to the microphone sound.
  • Fine-tune microphone effects with the 'DELAY' and 'REVERB' adjustments.

8. Maintenance

  • Clean the amplifier's exterior with a soft, dry cloth. Do not use liquid cleaners or aerosols.
  • Ensure ventilation openings are clear of dust and debris.
  • Store the amplifier in a cool, dry place when not in use for extended periods.

9. Troubleshooting

ProblemPossible CauseSolution
No powerPower cord not connected; Power switch off; No power from outletCheck power cord connection; Turn power switch on; Test outlet with another device
No sound outputIncorrect input selected; Volume too low; Speaker cables loose/incorrectly connected; Mute function activeSelect correct input source; Increase volume; Check speaker connections and polarity; Deactivate mute
Bluetooth not connectingAmplifier not in pairing mode; Device too far; Bluetooth already connected to another deviceEnsure 'BT' input is selected; Move device closer; Disconnect from other devices and try again
USB/SD card not playingIncorrect format; Card not inserted properly; Card capacity too largeEnsure files are in supported format (e.g., MP3); Reinsert card; Use a card up to 64GB
Poor FM receptionAntenna not connected or poorly positionedConnect FM antenna; Adjust antenna position for better signal

10. User Tips

  • For optimal sound quality, ensure your speakers match the amplifier's impedance range (4-16 ohms).
  • When using microphones for karaoke, experiment with the Echo and Delay controls to find the best vocal effect for your voice.
  • To prevent overheating, always ensure the amplifier has sufficient airflow around its vents.

11. Warranty and Support

For any issues or questions not covered in this manual, please contact the seller or authorized service center for assistance. Keep your purchase receipt as proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.