1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the SR SUNTOUR XCR LO Cartridge, model FUN006-26. This component is a traditional shoulder lockout damping rod designed for compatible SR SUNTOUR XCR front forks with 26-27.5 inch wheel sizes. It features a nitrogen-sealed, lightweight steel design with an oil spring damping system, offering reliable lockout functionality for mountain bikes.

Figure 1: SR SUNTOUR XCR FUN006-26 Cartridge for 26-27.5 inch Fork
2. Safety Warnings
CHILD SAFETY ALERT:
- All metal components (sharp edges, bolts), small parts, and moving mechanisms must be kept out of children's reach (under 12 years old).
- Children must not attempt to assemble, disassemble, or touch bicycle parts. Risk of cuts, pinching injuries, choking (small parts), or mechanical failure exists.
- Adult supervision is required during installation, maintenance, and storage.
General Safety:
- Always inspect all bolts and components of your bicycle, including the fork and cartridge, before each ride. Tighten any loose fasteners immediately.
- Do not modify structural parts of the fork or cartridge without manufacturer approval.
- Store the bicycle in a dry, child-proof area.
- Replace worn or damaged fork components with compatible parts only.
- Improper installation or disregard of safety instructions may result in injury. For professional assistance, contact a certified bicycle mechanic.
3. Preparation Tools (Required)
The following tools are recommended for the installation and maintenance of the XCR LO Cartridge:
- Hex wrench set (4mm, 5mm, 6mm)
- Torque wrench (recommended range: 4-12 Nm)
- Screwdriver (Phillips & flat-head)
- Appropriate fork oil (if servicing the fork damping system)
4. Installation
This cartridge is designed as a replacement or upgrade for compatible SR SUNTOUR XCR 26-27.5 inch front forks. Refer to your specific fork's manual for detailed disassembly and reassembly procedures. The following steps are general guidelines for cartridge installation:
- Fork Disassembly: Carefully disassemble your SR SUNTOUR XCR fork according to its specific service manual to access the existing damping rod/cartridge.
- Cartridge Insertion: Insert the new FUN006-26 cartridge into the designated stanchion tube. Ensure it seats correctly.
- Tightening: Secure the cartridge in place. If applicable, tighten any retaining bolts to the manufacturer's specified torque (typically 4-12 Nm). Use a torque wrench to prevent over-tightening or under-tightening.
- End Cap: The cartridge features a removable top end cap with an outer diameter of approximately 30mm. Ensure it is securely fastened.

Figure 2: Outer diameter of end cap thread (approx. 29.5mm)
- Fork Reassembly: Reassemble the fork components, ensuring all seals, bushings, and other parts are correctly positioned and lubricated as per your fork's service manual.
- Final Checks: Before riding, ensure the fork operates smoothly, and the lockout function engages and disengages properly. Check for any unusual noises or play.
Important Note:
- Avoid disassembling the internal damping system of the cartridge without professional tools and knowledge.
- Ensure stanchions are clean and dry before reassembly.
5. Operation (Lockout Function)
The FUN006-26 cartridge provides a traditional shoulder lockout mechanism. This allows you to stiffen the fork's suspension, typically for climbing or riding on smooth terrain, by turning a lever or dial located on the top of the fork crown.
- Engaging Lockout: Turn the lockout lever/dial to the 'locked' position. This will restrict the fork's travel, making it more rigid.
- Disengaging Lockout: Turn the lockout lever/dial back to the 'unlocked' or 'open' position to allow the fork to absorb impacts and provide suspension travel.
Always operate the lockout mechanism smoothly. Avoid forcing the lever. It is generally recommended to disengage the lockout when riding on rough terrain to prevent damage to the fork and improve rider comfort and control.

Figure 3: Top cap and lockout mechanism
6. Maintenance
Proper maintenance ensures the longevity and performance of your XCR LO Cartridge and fork:
- Clean Stanchions: After each ride, especially in dirty or wet conditions, clean the fork stanchions with a microfiber cloth. Avoid abrasive materials that could scratch the stanchion surface.
- Check for Leakage: Regularly inspect the fork for any signs of oil leakage around the seals. If leakage is detected, consult a professional mechanic.
- General Fork Inspection: Periodically check for loose headset bearings (no play when wiggling the handlebar) and ensure all fork bolts are tightened to specification.
- Cartridge Integrity: The cartridge is nitrogen-sealed. Do not attempt to open or modify the cartridge itself.
7. Troubleshooting
If you encounter issues with your XCR LO Cartridge, consider the following:
- Lockout Not Engaging/Disengaging:
- Check if the lockout lever/dial is fully rotated to the desired position.
- Inspect the lockout cable (if applicable) for proper tension and routing.
- Ensure the fork is clean and free of debris that might impede the mechanism.
- If the issue persists, the internal mechanism may require professional inspection.
- Unusual Noises or Play:
- Verify all fork bolts, including those securing the cartridge, are tightened to the correct torque.
- Check headset bearings for play and adjust if necessary.
- If noises persist, consult a qualified bicycle mechanic.
- Oil Leakage:
- Small amounts of oil residue on stanchions after a ride can be normal. However, significant or continuous leakage indicates a seal issue. Seek professional service immediately.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | SR SUNTOUR |
| Model Number | FUN006-26 |
| Compatibility | SR SUNTOUR XCR 26-27.5 Inch Front Forks |
| Type | Traditional Shoulder Lockout Damping Rod (Oil Spring Fork) |
| Material | Steel (Lightweight design) |
| Damping System | Oil Damping / Spring Resilience |
| End Cap Thread Outer Diameter | Approx. 30mm (Removable) |
| Suspension | Yes |
| Use | Mountain Bikes |
| Fit For | Disc Brake |

Figure 4: Model number 'FUN006-26' on cartridge body
9. User Tips
- This cartridge has been successfully installed in SR SUNTOUR XCR 32 R26 suspensions and is reported to work very well, with the lockout function performing as expected.
- If the top cap size differs from your original, it may be possible to unscrew and install your original top cap onto this cartridge. The plastic top cap is generally replaceable.
- While functional, this cartridge might be slightly heavier than some original components.
10. Frequently Asked Questions
- Q: What is the length of the cartridge?
- A: The cartridge is designed for SR SUNTOUR XCR 26-27.5 inch front forks. The outer diameter of the end cap thread is approximately 30mm. Specific overall length may vary slightly but is compatible with the stated fork sizes.
11. Warranty and Support
For warranty claims, technical support, or service inquiries, please contact the original seller or SR SUNTOUR authorized service centers. Keep your proof of purchase for any warranty-related issues.
For additional information and documents, you may refer to the official user manual PDF: User manual (PDF)