Garmin 18 Pin Cable for Garmin GPSMAP Series

Contents

18 PIN Marine GPS Cable Instruction Manual

For Garmin GPSMAP 172/178, 188/188C/198C, 392/398/492/498, 2010/3006/3010/3206/3210

Model: 18 Pin Cable for Garmin GPSMAP Series

1. Introduction

This manual provides instructions for the 18-pin marine GPS cable, a 'cutting version' designed for use with various Garmin GPSMAP models. This cable is a used product, confirmed to be in working condition, with the 6-pin cables shortened to approximately 5-6cm for custom installations. It is intended for users who need to replace or custom-wire their Garmin marine GPS units.

2. Setup and Installation

Important: Installation of this 'cutting version' cable requires technical knowledge of marine electronics wiring. If you are unsure, please consult a qualified marine technician.

  1. Inspect the Cable: Before installation, carefully inspect the 18-pin cable for any visible damage. Ensure the 18-pin connector is intact and the shortened 6-pin cables are ready for connection.
  2. Identify Wires: The 'cutting version' implies that the individual wires are exposed. You will need to correctly identify each wire's function (e.g., power, ground, data in/out) by consulting the wiring diagram for your specific Garmin GPSMAP model. This information is crucial for proper functionality and to prevent damage to your device.
  3. Prepare Connections: Strip the ends of the exposed wires as needed. Prepare the corresponding wires on your GPSMAP unit or existing wiring harness for connection.
  4. Connect Wires: Carefully connect the wires from the 18-pin cable to your GPSMAP system according to the wiring diagram. Use appropriate marine-grade connectors (e.g., heat-shrink butt connectors, solder and heat shrink) to ensure secure, waterproof, and corrosion-resistant connections.
  5. Secure the Cable: Once all connections are made and verified, secure the cable to prevent strain on the connections and protect it from movement and environmental factors.
  6. Connect to GPSMAP Unit: Plug the 18-pin connector firmly into the corresponding port on your Garmin GPSMAP device.
Full view of the 18-pin marine GPS cable with its connector and cut wires.
Figure 1: Overview of the 18-pin marine GPS cable. This image shows the full length of the cable, the 18-pin connector, and the shortened 6-pin cables ready for custom wiring.
Close-up view of the 18-pin connector showing the pin configuration.
Figure 2: Close-up of the 18-pin connector. This image provides a detailed view of the pin layout, which is essential for ensuring correct alignment and connection to the GPSMAP unit.

3. Operating Instructions

This 18-pin cable serves as a connectivity component for your Garmin GPSMAP unit. Once properly installed, its operation is passive. The cable facilitates the power supply and data communication between your GPSMAP device and other marine electronics or power sources. Ensure your GPSMAP unit is powered on and configured according to its own user manual to utilize the connections provided by this cable.

4. Maintenance

To ensure the longevity and reliable performance of your 18-pin marine GPS cable:

  • Regular Inspection: Periodically check the cable and its connections for any signs of wear, corrosion, or damage, especially in marine environments.
  • Clean Connections: Keep the 18-pin connector clean and free of dirt, salt, and moisture. Use a soft, dry cloth for cleaning.
  • Secure Routing: Ensure the cable is routed in a way that minimizes bending, pinching, or abrasion. Use cable ties or clamps to secure it.
  • Avoid Strain: Do not pull on the cable to disconnect it from the GPSMAP unit. Always grasp the connector itself.

5. Troubleshooting

If you experience issues with your Garmin GPSMAP unit after installing this cable, consider the following:

  • No Power to GPSMAP:
    • Check all power connections for proper wiring and secure contact.
    • Verify the power source (e.g., boat battery) is supplying adequate voltage.
    • Inspect any inline fuses for your GPSMAP unit.
  • Intermittent Connectivity/Data Issues:
    • Ensure the 18-pin connector is fully seated in the GPSMAP port.
    • Re-check all custom wire connections for looseness or corrosion.
    • Confirm that data wires are correctly identified and connected according to your GPSMAP model's wiring diagram.
  • Physical Damage: If the cable or connector shows signs of physical damage, it may need replacement.

6. Specifications

FeatureDetail
Model Number18 Pin
OriginTaiwan (China)
CompatibilityGarmin GPSMAP 172/178, 188/188C/198C, 392/398/492/498, 2010/3006/3010/3206/3210
Cable TypeMarine GPS Cable, 'Cutting Version'
ConditionUsed, working well, 6-pin cables cut short (approx. 5-6cm left)
Package Dimensions (approx.)Length: 16 cm, Width: 12 cm, Height: 6 cm
Package Weight (approx.)0.2 kg

7. User Tips

No specific user tips were available from reviews or Q&A for this product. Always refer to your Garmin GPSMAP unit's original manual for detailed wiring diagrams and operational procedures.

8. Warranty and Support

As this is a used product and a 'cutting version' cable, specific warranty information may vary. Please contact the seller directly for any questions regarding product support, returns, or warranty claims. Ensure you retain your purchase records for any inquiries.

© 2023 Garmin GPSMAP Cable Manual. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.