Allsome BG-5167

Contents

ALLSOME 6-Speed 800W Benchtop Drill Press Drilling Machine BG-5167 User Manual

Model: BG-5167 | Brand: Allsome

1. Introduction

Thank you for choosing the ALLSOME 6-Speed 800W Benchtop Drill Press, Model BG-5167. This precision drilling machine is designed for both industrial and home use, offering powerful motor performance and variable speed control. Please read this manual carefully before operation to ensure safe and efficient use of the machine.

2. Safety Instructions

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. SAVE THESE INSTRUCTIONS.

Work Area Safety

  • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Keep the floor around the machine clean and free of scrap material and grease.
  • Do not operate the drill press in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The machine creates sparks which may ignite dust or fumes.
  • Keep bystanders, children, and visitors away while operating the machine. Distractions can cause you to lose control.

Electrical Safety

  • Before plugging in the machine, be certain the voltage supplied is within the voltage marked on the nameplate. Do not use if the voltage is not correct. This machine is designed for AC power supply.
  • Use only with a properly grounded three-wire plug.
  • Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. Electrician's rubber gloves and footwear will further enhance your personal safety.
  • Do not expose the drill press to rain or wet conditions. Water entering a machine will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord to carry the machine or pull the plug from an outlet. Keep the cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

3. Product Overview

Familiarize yourself with the components of your ALLSOME Benchtop Drill Press:

Diagram of ALLSOME Benchtop Drill Press with labeled parts

Figure 1: Labeled Components of the Drill Press

  • Switch: Power ON/OFF control.
  • Operating Handle: Used to lower and raise the drill head.
  • External Carbon Brush: Accessible for maintenance.
  • Stroke Pointer: Indicates the drilling depth.
  • Stainless Steel Chuck: Holds the drill bits.
  • Bold Column: Main support pillar.
  • Chassis Fixing Screw Hole: For securing the column to the base.
  • Accessory Fixing Slot: For mounting accessories like vises.
  • Thickened Base: Provides stability.

4. Specifications

AttributeValue
Model NumberBG-5167
Voltage220V
Frequency50Hz
Rated Input Power800W
No-Load Speed0-2800 r/min
Chuck CapacityØ 1.5-13mm
Max. Travel60mm
Working Radius128mm
Tube SizeØ32 * 2.5 * 500mm
Weight12Kg
Max. Drilling Diameter (Iron)Ø8mm
Max. Drilling Diameter (Wood)Ø30mm
Power SourceAC
Drill TypeDrill Press
UseRenovation Team
Battery IncludedNo
High-concerned chemicalNone
Is CustomizedYes
CertificationNone

Product dimensions: Base approx. 19cm x 17cm, Column diameter approx. 32mm.

Product dimensions diagram

Figure 2: Product Size Diagram (Manual measurement, for reference only)

5. Assembly

Unpack the carton and verify that all parts listed below are included:

  • Head assy. (included chuck): 1 set
  • Base: 1 piece
  • Feed handle: 1 set
  • Elevator wheel (with screws): 1 set
  • Spare carbon brushes: 1 pair
  • Hex key (3mm, 5mm): 3 pieces
  • Chuck key (13mm): 1 piece
  • Wrench (14-17mm): 1 piece

Column Assembly

  1. Pass the head on a level floor.
  2. Place the base (2) on the head (1).
  3. Loosely attach the column to the base (2) as deeply as possible.
  4. Using attached S-hook, firmly tighten the two bolts that hold the column on the side of the base.

Assembly Feed Handle

Tighten the handle (4) into the feed shaft (4) and fix with screw (4).

Installing Drill Bit

  1. Insert the drill bit into the chuck jaws with 10mm depth. Make sure the drill bit is in the center of the chuck.
  2. Tighten the chuck with the chuck key. Make sure the drill bit is securely in position and tightened.
  3. Chuck can be released by using one hole only.

Video: Product demonstration including unboxing, assembly, and usage.

6. Operating Instructions

Power On/Off and Speed Control

  • The drill press features an On/Off switch for easy power control.
  • Adjust the output speed using the electronic speed controller (2k). Rotate the adjustment knob down or forward towards the '+' sign for higher speed, and up or towards the '-' sign for lower speed.

Adjusting the Guide Play

If the bench drill and guide have too much or too little play, it can be reset using the adjusting screw. First, release the nut, then set the play with the set screw, and finally re-tighten the nut. Avoid over-tightening the set screws to prevent damage.

Raising or Lowering the Head

  1. Loosen the key (3) by the other hand.
  2. Loosen two screws (4) of elevator (4).
  3. Lift or lower the head and elevator to the desired height.
  4. Tighten the head lever firmly again.

For small adjustments, loosen the lock knob (3) and rotate the elevator wheel to adjust the head height. It moves down or up by the depth stop point.

Adjusting the Depth Stop (6)

  1. Loosen the fixed screw (2) of depth point 2.
  2. Feed down the handle and let the drill bit touch the workpiece.
  3. Adjust the point 2(4) to the desired depth.
  4. Tighten the fixed screw again.
Hand operating the drill press handle to lower the drill bit

Figure 3: Operating the Feed Handle

Close-up of the depth stop mechanism on the drill press

Figure 4: Depth Stop Mechanism

7. Maintenance

General Maintenance

Preventative maintenance performed by unauthorized personnel may result in serious hazards. We recommend that all machine service be performed by a Factory Authorized Service Station.

Tool Lubrication

Your machine has been factory lubricated and is ready to use. It is recommended that machines with gears be regreased with a special gear lubricant at every brush change.

Carbon Brushes

The brushes and commutator in your power machine have been cleaned for many hours of dependable service. To maintain peak efficiency of the motor, we recommend that every 60 hours of operation the brushes be examined. Only genuine replacement brushes specially designed for your machine should be used.

Cleaning

Disconnect the machine from the power supply before cleaning or performing any maintenance. The machine may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air. Ventilating openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

CAUTION

Do not use cleaning agents and solvents damaging plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia, and household detergents that contain ammonia.

8. Troubleshooting

If you encounter any issues with your ALLSOME Benchtop Drill Press, please refer to the following common troubleshooting steps:

  • Machine not turning on: Ensure the power cord is securely plugged into a working outlet and the ON/OFF switch is in the 'ON' position. Check for tripped circuit breakers.
  • Reduced drilling performance: Verify that the drill bit is sharp and correctly installed in the chuck. Ensure the speed setting is appropriate for the material being drilled.
  • Excessive vibration or noise: Check for loose components, especially the column and base assembly. Ensure the workpiece is securely clamped.
  • Overheating: Allow the machine to cool down if it feels excessively hot. Ensure proper ventilation and avoid continuous heavy-duty use without breaks.

For persistent issues or complex repairs, it is recommended to contact a Factory Authorized Service Station or a qualified technician.

9. Warranty and Support

For any product support, warranty claims, or service inquiries, please contact the Allsome Official Store or your authorized dealer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.